User's Manual

SmartCard Reader

Mullion Single Gang

Technical Specifications

Model KT-MUL-MT-KP / KT-MUL-MT KT-MUL-SC-KP / KT-MUL-SC KT-SG-MT-KP / KT-SG-MT KT-SG-SC-KP / KT-SG-SC

Typical Read Range 13.56 MHz MIFARE Plus X,

encrypted sector, ID-1 Credentials (Cards)

Up to 1.2" Up to 1.6"

Typical Read Range 125 kHz ioProx ID-1

Credentials (Cards)

Up to 1.8" - Up to 2.0" -

Input Voltage 5VDC to 15VDC

Power Consumption @ 12V 175mA 70mA 160mA 70mA 175mA 70mA 160mA 70mA

Operating Humidity 0 to 95% non-condensing

Operating Temperature -40C to +70C (-40F to +158F)

Environmental Rating IP57

Dimensions (H.W.D.) mm 115.8 x 44.6 x 24.7 115.8 x 71.5 x 24.7

Dimensions (H.W.D.) in 4.56 x 1.75 x 0.97 4.56 x 2.81 x 0.97

Weight 108g (0.24lb) 106g (0.23lb) 105g (0.23lb) 103g (0.23lb) 173g (0.38lb) 166g (0.37lb) 170g (0.37lb) 161g (0.35lb)

Housing Polycarbonate, Smoked Black

RF Technologies 13.56 MHz and 125 kHz 13.56 MHz 13.56 MHz and 125 kHz 13.56 MHz

Capacitive Touch Keypad with backlighting x x x x

LED Indicator Multi-Color Bar: Red, Green, Yellow, Blue, Configurable

Sounder Integrated

Tamper Optical

Inputs Wiegand or RS-485: LED and Buzzer RS-485: 2 to 4 (configurable, using double device)

Output RS-485: 1 supervised, open-drain, up to 750mA

Wiring Terminal 6 Screwless Poles

Mounting Mullion North American Single Gang

Communication RS-485 Bus AES-128 Encrypted or Wiegand

Wiegand Formats 26-bit / 34-bit / Kantech XSF / Kantech SSF

Supported Credentials

13.56MHz

125kHz

MIFARE Plus X and ISO/IEC 14443A

ioProx - ioProx -

Cabling 3 Twisted pairs AWG 22 unshielded, up to 250' (75m)

Security Supports AES-128 Encryption between the Credential and the Reader as well as between the Reader and the Access Controller

Firmware Fully upgradable via RS-485

Certifications FCC, CE, UL, NIST, FIPS 197, RoHS, WEEE

Flammability Rating UL94 V-0

Warranty Limited Lifetime

Compatible Access Control Units:

Wiegand XSF KT-300, KT-400 and KT-1

Wiegand SSF KT-300, KT-400 and KT-1

RS485 KT-400 and KT-1

PAGE 1
SmartCard Reader Mullion Single Gang Technical Specifications Model KT-MUL-MT-KP / KT-MUL-MT Typical Read Range 13.56 MHz MIFARE Plus X, encrypted sector, ID-1 Credentials (Cards) KT-MUL-SC-KP / KT-MUL-SC KT-SG-MT-KP / KT-SG-MT Up to 1.2" Typical Read Range 125 kHz ioProx ID-1 Credentials (Cards) KT-SG-SC-KP / KT-SG-SC Up to 1.6" Up to 1.8" - Up to 2.
PAGE 2
SmartCard Reader Mounting Instructions Follow these instructions to install the reader: 1. Pull the controller’s wires in the wall through the hole in the mounting bracket. 2. Affix the mounting plate to the wall using two screws (#6-32). 3. If a higher level of tamper detection is desired, cut the plastic tamper tab from the mounting bracket. 4. Secure the white reflector tab back into the mounting plate hole with a screw. (#6-32). 5.