BATH VANITY WITH HEATER INSTRUCTION MANUAL MODEL # 15II500ARA IMPORTANT: RETAIN FOR FUTURE REFERENCE READ CAREFULLY For Customer Service: Questions, problems, missing parts? Twin-Star International, Inc. Delray Beach, FL 33445 Made in China Printed in China ©2012, Twin-Star International, Inc. www.twinstarhome.com 866-661-1218 8:30 a.m. - 5:30 p.m.
IMPORTANT INSTRUCTIONS Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product or assembly, please call customer service at 1-866-661-1218, 8:30 a.m.-5:30 p.m., EST, Monday-Friday. When using electrical appliances always follow basic precautions to reduce the risk of shock, and injury to persons including the following: 1. Read all instructions before using this appliance. 2.
IMPORTANT INSTRUCTIONS 21. Always plug heater directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 22. Reference Fig. 1 for grounding instructions. This heater is for use on 120 volts. The cord has a plug as shown in Fig. 1A. An adapter as shown in Fig.1C is available for connecting three-blade grounding type plugs to two-slot receptacles.
PACKAGE CONTENTS Fig. 2 B Remote Control A C Touch-up Pen Bath Vanity with Heater D E Wall Mounted Remote Holder Counter-top Remote Stand Part A B C D E Description Bath Vanity with Heater Remote Control Touch-up Pen Counter-top Remote Stand Wall Mounted Remote Holder Quantity 1 1 1 1 1 HARDWARE CONTENTS AA Screw 0.2 in. x 1.5 in.
HEATER LOCATION HEATER PLUG & MAIN POWER SWITCH When choosing a location for your new heater be sure that the general instructions are followed. Also, for best effect, install the heater out of direct sunlight. The heater is equipped with a ground fault circuit indicator plug. Plug the heater directly into a standard 120V outlet; the light will indicate correct function. 1. Press the TEST button,if the indicator light goes out function is correct. 2.
Remote Control Installation 5.2 5.1 D 5.3 Fig. 5 6.2 6.1 E 6.3 Fig.
Heater Functions: To Turn On or Off the Heater: Press the HEATER button which will turn on or off the heater regardless of the programed settings. To Adjust the Thermostat: Press the the THERMOSTAT button; the temperature display will start * ) \] ' theremostat adjustable range is 50°F to 97°F (10°C - 36°C.) To Change Between °F and °C: Press and hold the HEATER button for 4 seconds.
REPLACING THE REMOTE CONTROL BATTERIES When the remote control stops operating, or it’s range seems reduced, it is time to replace the batteries. To extend the life of the batteries remove the batteries if the remote control won’t be used for a long period of time. 1. The battery compartment is located on the back end of the remote. 2. Press the small tab inward as you slide the battery door open and remove the old batteries. 3.
TROUBLESHOOTING GUIDE PROBLEM SOLUTION 1. Heater does not blow warm air. @ " * " 3. The heater does not run in the program. 4. The heater is not responding to signals from the remote control. 5. The heater does not work. 1a. The ambient temperature is higher than the thermostat setting. 1b. Unplug the unit from the wall outlet for 2 hours. After 2 hours plug the unit back into wall outlet, and operate as normal. 1c. Check if the air inlet is blocked. 2a.
1-YEAR LIMITED WARRANTY The manufacturer warrants that your new vanity heater is free from manufacturing and material defects for a period of one year from date of purchase, subject to the following conditions and limitations. 1. Install and operate this electric heater in accordance with the installation and operating ! " = " ! accident, or misuse of the product shall nullify this warranty. 2.