INNOVATION AND INSPIRATION ON FIRE™ INSTALLATION, USE AND CARE MANUAL MODELS: TE1BQ36RS TE1BQ42RS TE1BQ54RS
A SPECIAL MESSAGE TO OUR CUSTOMERS... Congratulations on the purchase of your Twin Eagles grill! Our products are engineered for precision and designed for style. Each Twin Eagles grill is manufactured in the USA at our own state of the art facility in California. This manual will give you easy to follow instructions for installing, operating and maintaining your grill. We recommend reading this manual before your first use to ensure safety, proper care and operation.
TABLE OF CONTENTS CUSTOMER CARE GETTING STARTED ASSEMBLY INSTRUCTIONS BURNER INSTALLATION AIR SHUTTER ADJUSTMENT FEATURES GAS SAFETY REQUIREMENTS LP GAS HOOK-UP PORTABLE LP CONNECTION NATURAL GAS INSTALLATION CHECKING / CONVERTING THE REGULATOR LEAK TEST ELECTRICAL REQUIREMENTS LOCATING THE GRILL WINDY CONDITIONS INSULATION JACKET CUT-OUT DIMENSIONS INSULATING JACKET GRILL CUT-OUT DIMENSIONS OPERATING INSTRUCTIONS CLEANING & MAINTENANCE EAGLE ONE EXPLODED VIEW REPLACEMENT PARTS LIST WIRING DIAGRAM TROUBLE
IMPORTANT SAFETY INSTRUCTIONS WARNING! Read this manual carefully and completely before using your grill to ensure proper operation, proper installation, proper servicing and to reduce the risk of fire, burn hazard and/ or other injury. AVERTISSEMENT! Lire ce manuel avec soin et en entier avant l’utilisation de votre barbecue afin d’en assurer un fonctionnement, une installation et un entretien adéquats et réduire le risque d’incendie, de brûlures et d’autres blessures. FOR YOUR SAFETY If you smell gas: 1.
GENERAL SAFETY REQUIREMENTS • • • • • The installation of this appliance must conform with local codes or, in the absence of local codes, either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1 or Propane Storage and Handling Code, B149.
TWIN EAGLES | EAGLE ONE FEATURES: 1. 2. 3. 4. 5. 6. 7. 8. PRODUCT RATING PLATE KNOB AND BEZEL HOOD INFRARED GLASS ASSEMBLY BURNER GRATES WARMING RACK ROTISSERIE ROD INTERIOR LIGHT AND AMBIENT ILLUMINATION SWITCH 9. ROTISSERIE SWITCH 10. DRIP TRAY 11.
GETTING STARTED 1. Remove all packaging materials, labels and protective plastic film. DO NOT LEAVE UNIT IN THE SUN WITH PROTECTIVE PLASTIC FILM ON FOR AN EXTENDED PERIOD OF TIME AS IT WILL BECOME DIFFICULT TO REMOVE. 2. Check to ensure all grill accessories listed below are included.
ASSEMBLY INSTRUCTIONS Your Eagle One grill is fully assembled and tested in the factory and requires no major assembly in the field. For the purpose of safe shipping and transit, some parts such as the briquette trays and rotisserie components are wrapped inside the grill and require minor assembly. TO INSTALL BRIQUETTE TRAYS 1. Put briquette trays into the grill above the burner, as shown by placing the flash-tube-hole on the front. 2.
BURNER INSTALLATION CORRECT BURNER INSTALLATION The orifice is completely inserted into the venturi. U-burner bracket in proper position on the threaded stud. INCORRECT BURNER INSTALLATION The venturi is out of position and the orifice is not inserted into the venturi. 3 | www.twineaglesgrills.com Burner is out of position. The threaded stud must be inserted into the bracket of the burner and secured with a 1/4-20 keps nut.
AIR SHUTTER ADJUSTMENT Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply may make it necessary to adjust the burners. The flames of the U-burners should be visually checked. Flames should be blue and stable with little to no yellow tips, no excessive noise or lifting. If any of these conditions exist, remove the burner and check to see if any air shutter or burner ports are blocked by dirt, debris, spider webs, etc.
FEATURES Your Twin Eagles Eagle One Grill is equipped with many new and advanced features that put it at the forefront of at home grilling technology. Understanding these features and how they function is critical to maintaining the functionality of these features. Below are descriptions of these new grill features and how they integrate into your grilling experience.
FEATURES - cont. EXACT CONTROL ILLUMINATION The bezels of the Eagle One Grill have LEDs in them to give a visual representation of the heat setting of the burner. The grill is in stand-by when not in use; to wake the system, simply press in a knob. A blue light will appear above the knob and the back lights will come on. The back lights have a fade out feature, after remaining lit for 20 seconds they fade to black over five seconds.
GAS SAFETY REQUIREMENTS Each appliance is set and tested at the factory for the type of gas supply to be used. Identify the type of gas, either natural gas (NG) or Liquid Propane (LP) gas and make sure that the marking on the data plate (rating plate) matches the gas being supplied to the grill. This information is found on the data nameplate, located on the bottom right hand side of the firebox near the regulator.
LP GAS HOOK-UP BRASS COUPLING 3/8 FLARE BOTH ENDS OF THE REGULATOR INSULATING JACKET HI-PRESSURE LP HOSE ASSEMBLY LP REGULATOR TYPE 1 4.50” MIN CLEARANCE TO ALLOW LID TO FULLY OPEN 20LB (5 GALLON) LP CYLINDER DO NOT PLACE MORE THAN ONE CYLINDER IN THE ENCLOSURE AT ANY TIME. VENTS REQUIRED ON ENCLOSURES FOR LP CYLINDERS (MUST BE IN ACCORDANCE WITH ANSI Z21.58 STANDARDS) CAUTION: PROVIDE ADEQUATE VENTILATION HOLES IN THE ENCLOSURE FOR SAFETY PURPOSES IN THE EVENT OF A GAS LEAK.
PORTABLE LP CONNECTION One of the many features of the Twin Eagles grill base is the pullout slide pan for easy access to the LP gas tank. 1. To install the gas cylinder, pull out the slide pan and place the cylinder onto the pan. 2. Tighten the tank holding screw to secure the gas cylinder in place. 3. Check to ensure that the tank’s gas valve on top of the cylinder is closed. 4. Connect the LP regulator (included) to the cylinder and hand-tighten only.
NATURAL GAS INSTALLATION A typical natural gas installation is shown below. Make sure that the factory-supplied regulator is used and installed with the arrow mark on the regulator pointing towards the gas grill. Use only pipe sealants that are approved for use with natural and LP gases. An installer-supplied gas shutoff valve must be installed in an accessible location.
LEAK TEST CAUTION BEFORE TESTING: • NEVER USE THE GRILL WITHOUT FIRST LEAK TESTING THE GAS CONNECTIONS. • WARNING: DO NOT USE OPEN FLAME TO CHECK FOR LEAKS. USE OF AN OPEN FLAME COULD RESULT IN A FIRE, EXPLOSION AND BODILY HARM. • DO NOT SMOKE WHILE PERFORMING THE LEAK TEST! • To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area while performing a leak test. Perform leak test outdoors only.
ELECTRICAL REQUIREMENTS The appliance should only be taken apart by a qualified technician, or electrical shock may occur. It is rated at 120V, 4.4 Amps, 60Hz. REMINDER: Keep any electrical supply cord and the fuel supply hose away from any heated features. ! WARNING Electrical Grounding Instructions: This outdoor gas cooking appliance is equipped with a three prong (grounding) plug for your protection against shock hazard and should be plugged directly into properly grounded three prong outlets.
LOCATING THE GRILL This gas appliance is designed and certified for outdoor use only. Do not locate this grill under overhead combustible surfaces. When installed under overhead combustible surfaces, we recommend a ventilating hood wider than the appliance be installed with a minimum distance of 36 inches above the cooking surface. CAUTION should be taken when grills are used near glass, vinyl siding or other temperature sensitive construction materials.
WINDY CONDITIONS Your Eagle One grill has been designed and engineered to produce intense heat that sears food quickly, locking in the foods natural moisture and flavor. The grills burners require air for efficient burner combustion. This fresh air is pulled through a vent in the front of your grill and the intense hot air produced by the burners is expelled through a vent in the rear. If you are using your grill in windy conditions, the wind can disrupt this important airflow.
INSULATION JACKET CUT-OUT DIMENSIONS TE1BQ36RS Apply Weather Proof Sealant 28 1A "�" TEIJ36 1314 * "�" 26 * - ADD 3.5" TO ALLOW FOR HOOD OPENING SEE NOTE BELOW * 26 12A5 MODEL A B TEIJ36 40 3/4 39 1/2 TEIJ42 46 3/4 45 1/2 TEIJ54 58 3/4 57 1/2 COUNTER TOP OVERHANG WIDTH OF INSULATING JACKET INSULATING JACKET WARNING: Do not build the grill under overhead combustible construction.
GRILL CUT-OUT DIMENSIONS This is for non-combustible construction. For combustible construction refer back to previous page. TE1BQ54RS 54 TE1BQ42RS 42 52.25 TE1BQ36RS 24.25 36 11.P5 40.25 24.25 25 Y�T. 11.P5 34.25 * - ADD 5.00” TO ALLOW FOR HOOD OPENING 24.25 11.P5 * DETAIL 24.
OPERATING INSTRUCTIONS • • • • BEFORE LIGHTING THE GRILL WARNING DO NOT ATTEMPT TO LIGHT THE GRILL IF YOU SMELL GAS. WARNING: IT IS CRITICAL THAT THE GAS BURNERS ARE PROPERLY INSTALLED WITH THEIR ORIFICES INSIDE THE BURNERS AIR SHUTTERS. If not properly installed, gas may leak outside of the burner that could lead to fire, potential damage to your grill and bodily injury. (Please refer to Page 3 for correct burner installation).
OPERATING INSTRUCTIONS - cont. 3. Turn the control knobs to HI and allow the grill to preheat for 15 minutes or until desired temperature is displayed on the Temp Track. The hood is to be closed during this preheat period. 4. Place the food on the grill and cook to the desired temperature doneness. Adjust heat setting, if necessary. The control knob may be set to any position between HI and LO. 5. Allow grill to cool and clean the drip pan after each use. TO LIGHT THE ROTIS BURNERS 1.
OPERATING INSTRUCTIONS - cont. MATCH/BBQ LIGHTER LIGHTING INSTRUCTIONS If there is no electrical power supply available or if hot surface igniter will not light the U-Burner(s) or I.R. burner(s), the grill may be lit manually using a lighted long match, taper or BBQ lighter. 1. For the Rotisserie: insert a BBQ lighter through the match lite hole above the I.R. Glass assembly. For the U-burner: insert BBQ lighter through the match lite opening at the front of the grate, angled towards the burner. 2.
CLEANING & MAINTENANCE IMPORTANT Stainless Steel & General Product Care To keep your Twin Eagles products free of surface corrosion and in good working order, it is important to take additional precautions under certain conditions. If your Twin Eagles products are located in corrosive conditions, such as: • A coastal environment where corrosive salty air is present. • Near a swimming pool, hot tub or water feature with exposure to corrosive pool chemicals and/or chlorinated water.
CLEANING & MAINTENANCE - cont. GRATES The easiest way to clean the grates is to scrub them with a barbecue brush immediately after cooking is completed and the flame is turned off. Wear a barbecue mitt to protect your hands from the heat and steam. Dip a barbecue brush in tap water and scrub the hot grill. Dip the brush frequently in tap water. Steam, created as water comes in contact with the hot grill, helps loosen food particles stuck in the grill.
CLEANING & MAINTENANCE - cont. INFRARED SEAR BURNER The infrared burner has stainless housing and a protective screen. The protective screen helps reflect heat up to the cooking surface and also catches any food particles from landing on the ceramic burner. At the searing temperatures that the burner reaches all food particles will be burned off so the only maintenance required is cleaning the protective screen and checking for any objects that may be trapped.
23 | www.twineaglesgrills.
REPLACEMENT PARTS LIST ITEM NO. TE PART NUMBER DESCRIPTION TE1BQ TE1BQ TE1BQ TE1BQ TE1BQ TE1BQ 36RSN 36RSL 42RSN 42RSL 54RSN 54RSL 1 S27211-36WY 36 FRONT HOOD WELDED ASSEMBLY 1 1 - - - - 2 S27211-42WY 42 FRONT HOOD WELDED ASSEMBLY - - 1 1 - - 3 S27211-54WY 54 FRONT HOOD WELDED ASSEMBLY - - - - 1 1 4 S12368-36 HOOD HANDLE (Ø1.25" X 27.85") 1 1 - - - - 5 S12368-42 HOOD HANDLE (Ø1.25" X 33.85") - - 1 1 - - 6 S12368-54 HOOD HANDLE (Ø1.25" X 45.
REPLACEMENT PARTS LIST - cont. ITEM NO.
REPLACEMENT PARTS LIST - cont. ITEM NO.
REPLACEMENT PARTS LIST - cont. ITEM NO.
C K FEED NC + NO K LINE 1 - W NEUT 2 MOOD LIGHT SW CONN RED H.S.
TROUBLESHOOTING GUIDE BEFORE CALLING FOR SERVICE: If your Eagle One grill does not function properly, use the following troubleshooting guide before contacting your dealer for service. The troubleshooting guide may save the cost of a service call and the inconvenience of being without your grill. PROBLEM WHAT TO DO 1. Push in the knob and verify that the igniter glows. 2. If the igniter does not glow, verify proper power supply: GFCI 120V, 4.4A, 60Hz • Purge the line of any trapped air.
WARRANTY • LIMITED LIFETIME WARRANTY: Twin Eagles warrants the stainless steel main burners, hexagonal grates and all fabricated stainless-steel components, to be free from defects in materials and workmanship under normal residential use for the lifetime of the product. This warranty excludes discoloration, surface scratches, weather and atmospheric related staining, and minor surface rust and oxidation which are normal conditions and are to be expected with any outdoor product.
HOW TO OBTAIN SERVICE For service, please contact your Twin Eagles dealer or call Twin Eagles direct at (562) 263-3600 or fax (562) 802-3391 Mailing address: Twin Eagles, Inc. 13259 East 166th Street Cerritos, CA 90703 Visit us at www.twineaglesgrills.
CUT HERE P/N: 17582G 05/21 Place Postage Here INNOVATION AND INSPIRATION ON FIRE™ Customer Service ATTN: Warranty Department 13259 East 166th Street Cerritos, CA 90703 Fax no.