Quick Start Guide

Package
Overview
Cable Connection
Installation
1
2
3
4
30° 30°
30° 30°
2m
3m
Height Requirement
H=1.45m
0.5m
1m
Face Recognition Terminal
Quick Start Guide
About This Manual
All pictures, images, icons and snapshots in this manual are for reference only. If there is
inconsistency between the manual and the actual product, the actual product shall prevail.
The manual will be updated according to the product improvement and are subject to
change without prior written notice.
Legal Disclaimer
To the maximum extent permitted by applicable law, the product described, with its
hardware, software, software and firmware, is provided “as is”, with all faults and
errors, and our company makes no warranties, express or implied, including particular
purpose, and non-infringement of third party. In no event will our company, offices, or
agents be liable to you for any special, consequential, incidental, or indirect damages,
including, among others, damages for loss of business profits, business interruption, or
loss of data or documentation, in connection with the use of this product, even if our
company has been advised of the possibility of such damages.
With regard to the product with internet access, the use of product shall be wholly at your
own risks. Our company shall be irresponsible for abnormal operation, privacy leakage
or other damages resulting from cyber attack, hacker attack, virus inspection, or other
internet security risks; however, our company will provide timely technical support if
necessary.
During the use of the device, pleas strictly abide by applicable law. In the event of any
conflicts between this manual and the applicable law, the later prevails.
Installation and Use
Please use our product according to the following safety instructions and warnings.
Do not place the camera in extremely hot, cold, dusty or damp location.
Do not expose it to high electromagnetic radiation.
If the product does not work properly, please contact your dealer or the nearest service
center.
Never attempt to disassemble the camera yourself. (We shall not be responsible for any
problems caused by unauthorized repair or maintenance.)
Do not drop the camera or subject it to physical shock.
Keep away from liquid while in use.
Do not touch the screen with sharp objects.
If cleaning is necessary, please use clean cloth to wipe it gently, avoiding water or alcohol.
Front
Left
Right
Back
Note:
* The wiegand terminal here is a wiegand input terminal. If you want to connect
to an access controller, you shall set the Wiegand direction to “Output”.
* A card reader can be connected to this device via RS 485 interface independently.
2CH alarm input
20-pin Interface
RS 485
2CH alarm output Lock interface Wiegand interface Exit button
connector
Make sure faces can be captured clearly.
Avoid direct sunlight and backlight .
The device should be at least 2 meters away from the light, and at
least 3 meters away from the window or door.
Ambient Illumination Requirement
The recommended installation height (H) is 1.45m which can cover
human height of 1.2m ~2.2m in the detection area. It can be adjusted
according to the actual scene. The ideal recognition distance ranges from
0.5m to 1m.
Drill
Template
Paste the drill template onto the wall and
then drill the holes according to it.
Installation
1 2 3 4
Bracket
Gang box
Wall
Install the gang box on the wall.
Secure the bracket onto the wall with 4 screws.
Route and connect the cables and then
install the cable cover.
Hang the device onto the bracket hook and
then tighten the screws.
Direct/indirect
sunlight through
window
Plastic Plug ×4
Device
Quick Start Guide
CD
Drill Template Bracket
Tapping Screw×4
Screw (KM3*7)×6
L-wrenchCable Cover
(KM3*7)
Screws
Cable Cover
Cable Entry
Screws
(KM3*7)
Ethernet
Connector
138.6 mm
30.5 mm
285.8 mm
Infrared
Light
Display
Screen
Speaker
White Fill
Light
Cameras
Micro SD
Card Slot
Reset
USB
Port
Microphone
Card Swiping Area
20-pin
Interface
Anti-
Tamper
Button
Power
Interface
1 2 3
4
5
6
7
8 9 10 11 12 13 14 15 16 17 1918 20
NO2 NO1 NO3COM2 COM1 COM3
NC3
D+ D-
GND GND
IN1
GND
IN2
GND
D0 D1
GND
BUT SEN
Door contact
interface
Sensor
GND
+12V
GND
Power Input
12V0
PE
GND
IN1
GND
D0
GND
D1
+
+
+
+
+
+
-
-
-
-
-
-
RS485+
RS485-
Anode/
Magnetic
Lock
Cathode
Lock
D0
D1
GND
NC3
COM3
NO3
IN2
GND
COM1
NO1
COM2
NO2
D+
D-
BUT
GND
Alarm Input1
Alarm
Output1
Alarm Input2
Alarm
Output2
RS 485
Wiegand
Interface
Lock
Exit Button
Earth
Alarm Input Device
Alarm Input Device
Alarm Output Device
Alarm Output Device
Power
Power
Power
P
ower
Card
Reader
Exit Button
Router
Switch
Or
Door
Contact
Door
Contact