2 Megapixel Face Recognition Access Control Terminal TD-E2123 User Manual Please read this instruction carefully before operating the unit and keep it for further reference
Face Recognition &Access Control Terminal User Manual Notes on Safety This product is intended to be supplied by a Listed Power Unit, marked with 'Limited Power Source', 'LPS' on unit, output rated minimum 12V/1 A, no more than 2000m altitude of operation and Tma=60 Deg.C. Do not attempt to disassemble the camera; in order to prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside.
Face Recognition &Access Control Terminal User Manual Disclaimer With regard to the product with internet access, the use of product shall be wholly at your own risks. Our company shall be irresponsible for abnormal operation, privacy leakage or other damages resulting from cyber attack, hacker attack, virus inspection, or other internet security risks; however, our company will provide timely technical support if necessary. Surveillance laws vary from country to country.
Face Recognition &Access Control Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 1. FCC compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Face Recognition &Access Control Terminal User Manual 2012/19/EU (WEEE directive): The Directive on waste electrical and electronic equipment (WEEE Directive). To improve the environmental management of WEEE, the improvement of collection, treatment and recycling of electronics at the end of their life is essential. Therefore, the product marked with this symbol must be disposed of in a responsible manner.
Face Recognition &Access Control Terminal User Manual Table of Contents 1 2 Introduction ..................................................................................................................... 1 Login & Network Connection ........................................................................................ 2 2.1 Wired Network Connection ...............................................................................2 2.1.1 Access through IP-Tool ..........................................
Face Recognition &Access Control Terminal User Manual 6.4.6 RTSP .........................................................................................................34 6.4.7 UPnP .........................................................................................................35 6.4.8 Email .........................................................................................................36 6.4.9 FTP .........................................................................................
Face Recognition &Access Control Terminal User Manual 1 Introduction This series of product is specially designed and developed for face recognition and access control applications, featuring high performance and reliability, faster recognition and higher accuracy rate. Based on deep-learning algorithm, it combines identity authorization and access control.
Face Recognition &Access Control Terminal User Manual 2 Login & Network Connection 2.1 Wired Network Connection In LAN, there are two ways to access IP-Cam: 1. access through IP-Tool; 2. directly access through IE browser. 2.1.1 Access through IP-Tool Network connection: ① Make sure the PC and IP-Cam are connected to the local network and the IP-Tool is installed in the PC from the supplier. ② Double click the IP-Tool icon on the desktop to run this software as shown below: ③ Modify the IP address.
Face Recognition &Access Control Terminal User Manual For example, the IP address of your computer is 192.168.1.4. So the IP address of the camera shall be changed to 192.168.1.X. After modification, please enter the password of the administrator and click the “Modify” button to modify the setting. The default password of the administrator is “123456”. ④ Double click the IP address and then the system will pop up the IE browser to connect IP-CAM.
Face Recognition &Access Control Terminal User Manual The system will pop up the above-mentioned textbox to ask you to change the default password. It is strongly recommended to change the default password for account security. If “Do not show again” is checked, the textbox will not appear next time. 2.1.2 Directly Access through IE The default network settings are as shown below: IP address: 192.168.226.201 Subnet Mask: 255.255.255.0 Gateway: 192.168.226.
Face Recognition &Access Control Terminal User Manual Select “Properties” and then select internet protocol according to the actual situation (for example: IPv4). Next, click the “Properties” button to set the network of the PC. ② Open the IE browser and enter the default address of IP-CAM and confirm. ③ Follow directions to download and install the Active X control. ④ Enter the default username and password in the login window and then enter to view. 2.1.
Face Recognition &Access Control Terminal User Manual ① Make sure the camera is well connected via LAN and then log in the camera via LAN and go to ConfigNetworkPort menu to set the port number. Port Setup ② Go to Config NetworkTCP/IP menu to modify the IP address. IP Setup ③ Go to the router’s management interface through IE browser to forward the IP address and port of the camera in the “Virtual Server”.
Face Recognition &Access Control Terminal User Manual Router Setup ④ Open the IE browser and enter its WAN IP and http port to access. (for example, if the http port is changed to 81, please enter “192.198.1.201:81” in the address bar of web browser to access). Access through PPPoE dial-up Network connection Access the camera through PPPoE auto dial-up. The setting steps are as follow: ① Go to ConfigNetworkPort menu to set the port number. ② Go to Config NetworkTCP/IPPPPoE Config menu.
Face Recognition &Access Control Terminal User Manual Access through static IP Network connection The setting steps are as follow: ① Go to ConfigNetworkPort menu to set the port number. ② Go to Config NetworkTCP/IP menu to set the IP address. Check “Use the following IP address” and then enter the static IP address and other parameters. ③ Open the IE browser and enter its WAN IP and http port to access. 2.2 Wi-Fi Connection ① Use the network cable to connect the camera and wireless router or AP.
Face Recognition &Access Control Terminal User Manual After that, select “Obtain an IP address automatically” or manually enter the IP address by clicking “Use the following IP address”. Then click “Save” to save the settings. ④ Pull the network cable out of the camera. ⑤ Run the IP-Tool and find the camera through IP address or MAC address. Then double click it listed in the IP-Tool or enter the IP address of the camera in the address bar of the web browser to access the camera. 2.
Face Recognition &Access Control Terminal User Manual ④ Run this APP in your phone and then add the camera to the APP by entering IP address or domain name. After that, enter the username and password of the IPC. Username: the default username is “admin”. Password: the default password is “123456”. ④ View the image through the APP. Please refer to the Mobile Surveillance User Manual for more details. In WAN ① Make sure your camera is connected to the Ethernet. ② Enable 2G/3G/4G/5G network of your phone.
Face Recognition &Access Control Terminal User Manual 3 Face Recognition Configuration 3.1 Face Match Settings Go to the face match configuration interface via Web Client to set the face match parameters. 1. Go to ConfigFaceFace Match Config interface. 2. Enable liveness detection. If enabled, the system can distinguish real faces from non-real face spoof attacks.
Face Recognition &Access Control Terminal User Manual Deduplication Period: In the set period, delete the repeated comparison results. Similarity threshold: When the similarity of the captured face picture and the face picture added into the face database exceeds the similarity threshold, alarms will be triggered. Send the face comparison data: if it is disabled, the face comparison result will be displayed neither on the screen of the terminal nor on the live interface of the web client.
Face Recognition &Access Control Terminal User Manual Click “Draw Area” and drag the border lines of the rectangle to modify its size. Move the rectangle to change its position. Click “Stop Draw” to stop drawing the area. Click “Clear” to clear the area. Then set the detectable face size by defining the maximum value and the minimum value (The default size range of a single face image occupies from 3% to 50% of the entire image). 3.
Face Recognition &Access Control Terminal User Manual ① Adding face pictures one by one Click to pop up an adding user box. Then click to select a face picture saved on the local PC. Please select the picture according to the specified format and size limit. After that, fill out the relevant information of the face picture and click “Entry” to add. List type: it includes allow list, visitor, block list.
Face Recognition &Access Control Terminal User Manual Click “Modify” to change people information and click “Delete” to delete this face picture.
Face Recognition &Access Control Terminal User Manual 4 Live View 4.1 Face Recognition View After configuring face database and face match, the face match result will be viewed on the screen. When detecting a face, the device will display the following interface. When the captured face is successfully matched, it will display “Match Success”.
Face Recognition &Access Control Terminal User Manual The following table is the instructions of the icons on the live view interface.
Face Recognition &Access Control Terminal User Manual Add captured face pictures to the face database Click a captured picture in area ①. This will bring a face picture adding box. Fill out the relevant information and click “Entry” to add this face picture.
Face Recognition &Access Control Terminal User Manual 5 Access Control Settings Here we take the access control settings of Web client for example. 5.1 Access Control System Settings Click ConfigAccess ControlAccess Control System Settings to go to the following interface. Select Language: Select the screen display language on the panel/tablet. Select Voice: Select the language of the voice prompt or the custom voice prompt.
Face Recognition &Access Control Terminal User Manual Select the voice you want to replace and then click “browse” to select the desired audio file. After that, click “Upload” to upload the audio file. Rename the audio as needed. After your own voice prompt is uploaded, you can select it from the audio list and click “Listen” to listen to your voice prompt. 5.2 Door Lock Settings Click ConfigAccess ControlDoor Lock to go to the following interface.
Face Recognition &Access Control Terminal User Manual For example, supposed that the unlocking mode of someone is set to “Face Comparison and Swiping Card”, this person shall be matched successfully and swipe the card on the device, and then he/she can pass. For a stranger, if you want to allow his/her access, the list type shall be set as “Stranger (including visitor and allow list), or the door cannot be linked to open. 5.
Face Recognition &Access Control Terminal User Manual are similar to the face match settings. Please refer to face match settings chapter for details. 5.4 Wiegand Settings Click ConfigAccess ControlWiegand Config to go to the following interface. Wiegand Config: Wiegand Input, Wiegand Output or Off can be selected. If the card reader is connected to the Wiegand interface, please select “Wiegand Input”. If the access controller is connected to the Wiegand interface, please select “Wiegand Output”.
Face Recognition &Access Control Terminal User Manual 6 Other Configurations You can set other configurations via the terminal or Web Client. Their setting steps are similar. Here we take the configurations of Web Client for example to introduce. In the Webcam client, choose “Config” to go to the configuration interface. Note: Wherever applicable, click the “Save” button to save the settings. 6.1 System Settings 6.1.
Face Recognition &Access Control Terminal User Manual Select the time zone and DST as required. Click the “Date and Time” tab to set the time mode. 6.1.3 Local Config Go to ConfigSystemLocal Config to set up the storage path of captured pictures and recorded videos on the local PC. There is also an option to enable or disable the bitrate display in the recorded files. Additionally, the local smart snapshot (face snapshot) storage can be enabled/disable here. 6.2 Image Configuration 6.2.
Face Recognition &Access Control Terminal User Manual Brightness: Set the brightness level of the camera’s image. Contrast: Set the color difference between the brightest and darkest parts. Hue: Set the total color degree of the image. Saturation: Set the degree of color purity. The purer the color, the brighter the image is.
Face Recognition &Access Control Terminal User Manual 60Hz: reduces flicker in 60Hz lighting conditions. White Balance: Adjust the color temperature according to the environment automatically. Frequency: 50Hz and 60Hz can be optional. Exposure Mode: Choose “Auto” or “Manual”. If manual is chosen, the digital shutter speed can be adjusted. Gain Mode: Choose “Auto” or “Manual”. If “Auto” is selected, the gain value will be automatically adjusted according to the actual situation.
Face Recognition &Access Control Terminal User Manual Three video streams can be adjustable. Resolution: The size of image. Frame rate: The higher the frame rate, the video is smoother. Bitrate type: CBR and VBR are optional. Bitrate is related to image quality. CBR means that no matter how much change is seen in the video scene, the compression bitrate will be kept constant. VBR means that the compression bitrate will be adjusted according to scene changes.
Face Recognition &Access Control Terminal User Manual Audio Encoding: G711A and G711U are selectable. Audio Type: MIC. 6.2.3 OSD Configuration Go to ImageOSD interface as shown below. Set time stamp, device name, OSD content and picture overlap here. After enabling the corresponding display and entering the content, drag them to change their position. Then click the “Save” button to save the settings.
Face Recognition &Access Control Terminal User Manual White Light Mode: “OFF”, “Manual” or “Auto” is optional. In low illumination condition, this mode can be enabled. Auto: The white light will be automatically enabled when collecting a face in low illumination condition. If the auto mode is selected, the duration time should be set for saving energy.
Face Recognition &Access Control Terminal User Manual Video Blur Detection: Alarms will be triggered if the video becomes blurry. Video Cast Detection: Alarms will be triggered if the video becomes obscured. 2. Set the alarm holding time. 3. Set the sensitivity of the exception detection. Drag the slider to set the sensitivity value or directly enter the sensitivity value in the textbox. Click “Save” button to save the settings.
Face Recognition &Access Control Terminal User Manual PPPoE and then enter the user name and password from your ISP. Either method of network connection can be used. If PPPoE is used to connect internet, the camera will get a dynamic WAN IP address. This IP address will change frequently. To be notified, the IP change notification function can be used. Click “IP Change Notification Config” to go to the interface as shown below.
Face Recognition &Access Control Terminal User Manual 2. Choose a wireless device on the list. The SSID and security mode of the wireless device will be shown automatically. Please don’t change it manually. 3. Enter the key to connect the wireless device. This key should be set on the wireless device in advance for wireless network connection. After the above-mentioned wireless network is configured, you can choose “Obtain an IP address automatically” or “Use the following IP address”.
Face Recognition &Access Control Terminal User Manual HTTPS Port: The default HTTPs port is 443. It can be changed to any port which is not occupied. Data Port: The default data port is 9008. Please change it as necessary. RTSP Port: The default port is 554. Please change it as necessary. Long Polling Port: The port is used for a persistent connection of the third-party platform to push smart data, like face pictures. 6.4.
Face Recognition &Access Control Terminal User Manual Create domain name. After the domain name is successfully applied for, the domain name will be listed as below. 3. Enter the username, password, domain you apply for in the DDNS configuration interface. 4. Click the “Save” button to save the settings. 6.4.6 RTSP Go to ConfigNetworkRTSP.
Face Recognition &Access Control Terminal User Manual Select “Enable” to enable the RTSP function. Port: Access port of the streaming media. The default number is 554. RTSP Address: The RTSP address (unicast) format that can be used to play the stream in a media player. Multicast Address Main stream: The address format is “rtsp://IP address: rtsp port/profile1?transportmode=mcast”. Sub stream: The address format is “rtsp://IP address: rtsp port/profile2?transportmode=mcast”.
Face Recognition &Access Control Terminal User Manual 6.4.8 Email If you need to trigger Email when an alarm happens or IP address is changed, please set the Email here first. Go to ConfigNetwork Email. Sender Address: sender’s e-mail address. User name and password: sender’s user name and password. If “Anonymous login” is selected, an anonymous Email will be sent when an alarm is triggered. Server Address: The SMTP IP address or host name.
Face Recognition &Access Control Terminal User Manual Click the “Test” button to test the connection of the account. Recipient Address: receiver’s e-mail address. 6.4.9 FTP After an FTP server is set up, captured pictures from events will be uploaded to the FTP server. Go to ConfigNetwork FTP. Server Name: The name of the FTP server. Server Address: The IP address or domain name of the FTP. Upload Path: The directory where files will be uploaded to. Port: The port of the FTP server.
Face Recognition &Access Control Terminal User Manual There is a certificate installed by default as shown above. Enable this function and save it. Then the camera can be accessed by entering https://IP: https port via the web browser (eg. https://192.168.226.201:443). A private certificate can be created if users don’t want to use the default one. Click “Delete” to cancel the default certificate. Then the following interface will be displayed.
Face Recognition &Access Control Terminal User Manual default. 6.5 Security Configuration 6.5.1 User Configuration Go to ConfigSecurityUser interface as shown below. Add user: 1. Click the “Add” button to pop up the following textbox. 2. Enter user name in “User Name” textbox. 3. Enter the password in the “Password” and “Confirm Password” textbox. It is recommended to set a high level password that shall be composed of numbers, special characters, upper or lower case letters for your account security.
Face Recognition &Access Control Terminal User Manual If this option is enabled, only the PC with the specified MAC address can access the camera for that user. 6. Click the “OK” button and then the newly added user will be displayed in the user list. Modify user: 1. Select a user to modify password and MAC address if necessary in the user configuration list box. 2. The “Edit user” dialog box pops up by clicking the “Modify” button. 3. Enter the old password of the user in the “Old Password” text box. 4.
Face Recognition &Access Control Terminal User Manual 6.5.3 Block and Allow Lists Go to ConfigSecurityBlock and Allow Lists as shown below. The setup steps are as follows: Check the “Enable address filtering” check box. Select “Block/Allow the following address”, IPv4/IPv6/MAC and then enter IP address or MAC address in the address box and click the “Add” button. 6.5.4 Security Management Go to ConfigSecuritySecurity Management as shown below.
Face Recognition &Access Control Terminal User Manual Import & Export Settings Configuration settings of the camera can be exported form a camera into another camera. 1. Click “Browse” to select the save path for import or export information on the PC. 2. Click the “Import Setting” or “Export Setting” button. Default Settings Click the “Load Default” button to restore all system settings to the default factory settings except those you want to keep. 6.6.2 Reboot Go to ConfigMaintenanceReboot.
Face Recognition &Access Control Terminal User Manual 1. Click the “Browse” button to select the save path of the upgrade file 2. Click the “Upgrade” button to start upgrading the firmware. 3. The device will restart automatically Caution! Do not close the browser or disconnect the camera from the network during the upgrade. 6.6.4 Operation Log To query and export log: 1. Go to ConfigMaintenanceOperation Log. 2. Select the main type, sub type, start and end time. 3.
Face Recognition &Access Control Terminal User Manual 7 Search 7.1 Image Search Click Search to go to the interface as shown below. Local Image Search 1. Choose “Picture”—“Local”. 2. Set time: Select date and choose the start and end time. 3. Click to search the images.
Face Recognition &Access Control Terminal User Manual 4. Double click a file name in the list to view the captured photos as shown above. Click to return to the previous interface. The descriptions of the buttons are shown as follows. Icon Description Icon Description Close: Select an image and click this Close all: Click this button to button to close the image. close all images. Fit size: Click to fit the image on the screen.
Face Recognition &Access Control Terminal User Manual 4. Double click on a file name in the list to start playback. Icon Description Icon Description Play button. After pausing the video, click this button Pause button to continue playing. Stop button Speed down Speed up Watermark display Enable / disable audio; drag the slider to adjust the volume after enabling audio.
Face Recognition &Access Control Terminal User Manual 8 Face Match Result Search Click “Data Record” tab to go to the face recognition result search interface. Set the start time and end time and click “Search” to view the face recognition result. Red time tag means no comparison result. Green time tag means there is a comparison result. Click the picture with green time tag and then the face comparison information can be viewed as shown below. Click the picture with red time tag.
Face Recognition &Access Control Terminal User Manual Appendix Appendix 1 Troubleshooting How to find the password? A：Reset the device to the default factory settings. Default IP: 192.168.226.201; User name: admin; Password: 123456 Fail to connect devices through IE browser. A: Network is not well connected. Check the connection and make sure it is connected well. B: IP address is not available. Reset the IP address. C: Web port number has been changed: contact administrator to get the correct port number.
Face Recognition &Access Control Terminal User Manual No sound can be heard. A：Audio input device is not connected. Please connect and try again. B: Audio function is not enabled at the corresponding channel. Please enable this function.
Face Recognition &Access Control Terminal User Manual Appendix 2 Specifications Camera Image Sensor 1/2.8" Progressive Scan CMOS Image Size 1920×1080 Electronic Shutter 1/2s ~ 1/100000s IRIS Type Fixed IRIS MIN. Illumination Lens 0 lux 2MP dual lens; f=3.6mm @F2.4; Vertical horizontal field of view: approx. 65°; horizontal field of view: approx. 50° Lens Mount M12 WDR 74dB BLC Yes HLC Yes Defog Yes DNR 2D/3D NR Image Video Compression H.265+/H.265/ H.264+/H.264/MJPEG H.
Face Recognition &Access Control Terminal User Manual Anti-Tamper Interface 1 CH Reset Button 1 Wiegand Interface Yes (Wiegand input or output configurable) WiFi Supports 2.
