T-C2 Series Operation Manual
1T-C2 SERIES OPERATION MANUAL
1T-C2 SERIES OPERATION MANUAL Table of Contents 1 DISCLAIMER ................................ ................................................................ 1 1.1 Regulatory Agency Acceptance........................................................................... 1 1.2 FCC Statement ................................................................................................... 1 1.3 Manual Version Information.................................................................................
1T-C2 SERIES OPERATION MANUAL 8.6.2 DVI Source Menu Items .................................................................................... 37 8.6.3 RGB Source Menu Items................................................................................... 39 8.6.4 CV & YC Source Menu Items ............................................................................ 40 8.6.5 Still Image Store / Testcard Source Menu Items................................................ 41 8.
1T-C2 SERIES OPERATION MANUAL 12.14 No video present from the UTP output. ............................................................. 68 13 RETURN PROCEDURE ................................ ............................................. 69 13.1 Are you sure there's a fault?.............................................................................. 69 13.2 To return a unit for repair................................................................................... 69 14 WARRANTY POLICY ............
1T-C2 SERIES OPERATION MANUAL 1 DISCLAIMER This product is intended for professional and/or home use. This product is not intended for use in a medical environment and does not have the required certifications for such use. Similarly, use aboard any aircraft or spacecraft while in flight or as an adjunct to any surface, airborne or marine navigation system or any offshore marine activity, including control of any watercraft, or any use similar to those specifically herein mentioned is prohibited.
1T-C2 SERIES OPERATION MANUAL Caution: This equipment is intended for use in the manner prescribed in the Instruction Manual. Any user changes or modifications not expressly approved by TV One Multimedia Solutions could void the user’s authority to operate the equipment. Connecting this equipment to external devices requires no specially shielded cabling for FCC compliance. The Instruction Manual shows or describes the proper connection of this equipment for operation that insures FCC compliance.
1T-C2 SERIES OPERATION MANUAL 2 IMPORTANT SAFETY INSTRUCTION To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference. To reduce the risk of electric shock, do not remove the cover from the unit. No user serviceable parts inside. Refer servicing to qualified personnel. 2.1 Power and connections This unit must be connected to a mains socket outlet with a protective earth connection.
1T-C2 SERIES OPERATION MANUAL 2.5 Ventilation Slots and openings in the sides of the unit are provided for ventilation. To ensure reliable operation, avoid obstruction of these openings and ensure the unit is installed in a well-ventilated area. 2.6 Intellectual property Some IC chips in this product include confidential and/or trade secret property. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or decompile the contents thereof.
1T-C2 SERIES OPERATION MANUAL 2 IMPORTANT: CONSIGNES DE SECURITE Afin de tirer le meilleur de ce produit, merci de lire attentivement ce manuel. Gardez-le dans un endroit sûr pour pouvoir le consulter à nouveau. Afin de réduire le risque de choc électrique, ne retirez pas l’unité de sa protection. Aucune pièce réparable par l’utilisateur à l’intérieur. Référez-vous à des personnes qualifiées. 2.
1T-C2 SERIES OPERATION MANUAL L’installation de cette unité doit se faire dans un endroit frais et sec, éloigné de sources excessives de chaleur, de vibrations, de poussière, d’humidité et de froid. 2.5 Aération Les rainures et les ouvertures sur les cotés de l’unité servent à l’aérer. Pour permettre une utilisation sûre, évitez d’obstruer ces ouvertures et assurez-vous que l’unité est installée dans un endroit bien aéré. 2.
1T-C2 SERIES OPERATION MANUAL 2 INSTRUCCIONES IMPORTANTES DE SEGURIDAD Para sacar el mejor provecho de este producto, léase este manual con detenimiento. Guárdelo en un lugar seguro para poder hacerle referencia en el futuro. Para reducir el riesgo de calambre, no quite la cubierta del aparato. No hay piezas utilizables dentro. Remítase todo mantenimiento a personal cualificado. 2.
1T-C2 SERIES OPERATION MANUAL 2.4 Ubicación Este aparato se debe instalar en un lugar seco y fresco, lejos de fuentes de calor excesivas, la vibración, el polvo, la humedad y el frío. 2.5 Ventilación El aparato viene provisto de ranuras y agujeros en los lados para la ventilación. Para asegurar una operación eficaz, se debe evitar la obstrucción de estos agujeros y también asegurar que el aparato se instale en una zona con adecuada ventilación. 2.
1T-C2 SERIES OPERATION MANUAL 2 WICHTIGE SICHERHEITSVORSCHRIFTEN Lesen Sie diese Bedienungsanleitung bitte sorgfältig, um Ihr Produkt optimal nützen zu können, und bewahren Sie sie zum späteren Nachschlagen an einem sicheren Ort auf. Entfernen Sie bitte keinesfalls die Abdeckung, um der Gefahr eines Stromschlags vorzubeugen. Im Inneren des Geräts befinden sich keine Teile, die vom Benutzer gewartet werden können. Lassen Sie Wartungsarbeiten nur von Fachpersonal durchführen. 2.
1T-C2 SERIES OPERATION MANUAL 2.3 Aufstellung Das Gerät sollte an einem kühlen, trockenen Ort aufgestellt werden, fern von übermäßiger Wärme, Vibrationen, Staub, Feuchtigkeit und Kälte. 2.5 Belüftung Seitliche Schlitze und Öffnungen sorgen für die Belüftung des Geräts. Um die ordnungsgemäße Belüftung zu gewährleisten, dürfen diese Öffnungen nicht verdeckt werden. Sorgen Sie außerdem dafür, dass das Gerät an einem gut belüfteten Ort aufgestellt wird. 2.
1T-C2 SERIES OPERATION MANUAL 2 BELANGRIJKE VEILIGHEIDSINSTRUCTIES Lees deze handleiding zorgvuldig door om het beste uit uw product te halen. Bewaar het op een veilige plek voor raadpleging in de toekomst. Haal nooit het omhulsel van de eenheid af, dit om de kans op een elektrische schok te verminderen. Maak het apparaat nooit open: er bevinden zich geen door de gebruiker in te stellen onderdelen in het apparaat. Laat service en onderhoud over aan een gekwalificeerde technicus. 2.
1T-C2 SERIES OPERATION MANUAL 2.4 Plaatsing Deze eenheid moet geïnstalleerd worden op een koele droge plaats, uit de buurt van bronnen van extreme hitte, vibraties, stof, vocht en kou. 2.5 Ventilatie De sleuven en openingen aan de zijkant van de eenheid zijn voor ventilatie. Zorg er voor dat de eenheid op een goed geventileerde plek geïnstalleerd wordt zodat deze betrouwbaar werkt. 2.6 Intellectueel eigendom Sommige IC chips in dit product bevatten vertrouwelijke informatie en/of fabrieksgeheimen.
1T-C2 SERIES OPERATION MANUAL 3 DEVICE SUMMARY 3.1 Device Capabilities The 1T-C2 series uses the proprietary CORIO®2 Engine to perform its functions, being the second generation of the successful CORIO® products. The CORIO ®2 technology is a powerful toolset for any application requiring high quality video signal conversion or image manipulation. All units feature a single video processing and scaling engine, with some unit’s also featuring video mixing, keying and fader capabilities.
1T-C2 SERIES OPERATION MANUAL PC/HD Scaler This unit allows computer / high-definition video scaling from one resolution to another – for example, 720p to 1080i, or VGA to XGA, etc. This unit does not have any overlay abilities. 3.2 Device Features General Topography 4:4:4 RGB / YUV sampling provides full bandwidth color which allows precise keying where included in the units capabilities. This can be achieved through the keys on the front of the unit.
1T-C2 SERIES OPERATION MANUAL 4 PRODUCT IMAGES Your 1T-C2 product should look like one of the units below. Each unit has a different main function (Down Converter or Video Scaler) and a subsequently different ability to process video signals.
1T-C2 SERIES OPERATION MANUAL 5 FRONT PANEL CONTROLS The range of buttons on the front of the unit provides the user with quick access for selecting a variety of inputs and features. Since all the units in the 1T-C2 series are different, not all of the descriptions below will be applicable to the unit in question. The mostly notable are the MIX/KEY/FADE buttons that are on certain units only.
1T-C2 SERIES OPERATION MANUAL 5.2 MENU and buttons The on-screen display (OSD) is controlled from the front panel by using these buttons. MENU will activate the OSD, whilst the and arrowed keys will allow different menu items to be selected and adjusted – this is detailed in a later section. 5.3 Advanced menus System Advanced menus [Off] The above menu item must be ‘On’ to activate certain menu items. These typically control the more advanced items in the menus. 5.
1T-C2 SERIES OPERATION MANUAL All stored settings except resolutions are lost when the unit is reset. A Firmware update is the only way to perform a complete factory reset (including resolution data). 5.4.4 Switching units between different resolutions using the front panel Down converters will default to outputting NTSC after a Factory Reset, whilst Video and PC/HD Scalers will default to outputting XGA (1024x768 @ 60Hz).
1T-C2 SERIES OPERATION MANUAL 6 VIDEO INPUTS AND OUTPUTS The units have different video inputs and outputs depending on your model, and with the PC/HD output being either scaled, or just as a loop-through from the PC/HD input. 6.1 Computer & Video inputs The PC/HD input can accept: Analog RGBHV RGsB (sync on green) RGBS (composite sync at TTL levels) YUV/YPbPr (including tri-level) In most cases, the particular input being used will be auto-detected.
1T-C2 SERIES OPERATION MANUAL RGBS (separate sync at TTL levels) YUV/YPbPr (including tri-level). However, please note that on some units such as Down Converters, the PC/HD output is there just to loop the PC image through to the PC monitor. On Video and PC/HD Scalers, bypass mode (with the unit in Standby) will feed PC/HD input to the PC/HD output directly.
1T-C2 SERIES OPERATION MANUAL 7 INFRA-RED REMOTE CONTROL Your unit is compatible with an optional infra-red remote control as shown below: Resets back to power-on defaults Stores current settings Selects input: 1/2/3=RGB/CV/YC Enables Keyer Enables Lock & Mix mode Fades in/out Starts AutoSet Locks the IR & panel buttons (Not used.) Selects flicker reduction level Sets Shrink/PIP size & position Navigates through the menu structure & changes values. Adjusts current menu values.
1T-C2 SERIES OPERATION MANUAL 8 MENU LAYOUT AND SETTINGS ADJUSTMENT From here on, we’ll be looking at the menu structure employed in the series and, more importantly, the individual menu items that allow you to take advantage of the power of the unit. You’ll be using the MENU and buttons and the on-screen display (OSD) to view the options and settings available to you. The OSD can be activated by pressing the MENU button once. Holding the MENU button in for a short while will then close the OSD.
1T-C2 SERIES OPERATION MANUAL CORIO2 TV One The first is the ‘welcome’ display shown above indicating the model of the unit. www.tvone.com SW: 65. PT: 12, BT: 13 Moving to the next menu item displays the firmware information screen (the numbers on your unit will be different to those shown). The SW number refers to the version of firmware loaded into the unit, this can be upgraded from the support website.
1T-C2 SERIES OPERATION MANUAL This menu item allows the lock mode to be selected and the lock source to be defined. The top line of the display shows the current detected resolution of the selected lock source (RGB1 in this example). The lock mode can be either Off, Genlock or Lock & Mix, with the operation of these shown in the following table: Lock mode Off Genlock Lock & Mix Frm.
1T-C2 SERIES OPERATION MANUAL 1024 x 768 60Hz Output res. [28] Your unit can handle a very wide array of inputs and convert them all to a single output signal with defined characteristics. This output resolution will remain in place until changed or it may be overridden by the lock mode and source. The top line of the display will show the current output resolution selected. Some units will have a limited number of output resolutions depending on their function (e.g.
1T-C2 SERIES OPERATION MANUAL Rep. active but the output is not currently encrypted. The repeater unit (e.g. scaler) attached is capable of HDCP, and the output from the unit is encrypted. Adjust outputs Output type scaling. As the DVI output is HDCP encrypted, then a HDCP-encrypted source can be selected for scaling. Note that no other output connector (SDI, CV, YC, YUV or RGBHV) will function – since they are not encrypted.
1T-C2 SERIES OPERATION MANUAL This menu item is only available on certain units when the Output resolution is set to PAL or NTSC. With this you can change the output filtering system to increase or decrease the image sharpness. In general, high sharpness can result in increased colour disturbance. Adjust outputs Back Y/U/V [ 16] [128] [128] Sets the value of the fixed background color, which is present when PIP is used with no Lock source background displayed.
1T-C2 SERIES OPERATION MANUAL Adjust windows Zoom level % [ 100] Changing this option, sets the amount of picture magnification you wish to use for the window Source. You are provided with the options to zoom the image from 100% to 1000% (10x zoom). Adjust windows H/V zoom pan % [ 50] [ 50] Once an image has been ‘zoomed’, this control allows the image to be positioned within the window so that any portion can be seen, not just the middle.
1T-C2 SERIES OPERATION MANUAL Note that some units do not have the [On] entry – this is only for units with a PIP button on the front, with turns this entry On and Off. On these units, this feature is ‘Off’ by default, so that the full image size of 100% is used. Shrink level will need to be turned On before any change to this value has an effect. Adjust windows H/V position % [100] [ 50] This menu option determines the position of the shrunken image on the monitor screen.
1T-C2 SERIES OPERATION MANUAL Off Low Med. High Adjust windows Image smoothing Disables flicker reduction (sharpest mode). Suitable for most input sources. Enough for most situations such as thin line drawings Highest amount of flicker reduction. Will cause loss of vertical detail in some images. [Auto] Image smoothing reduces the jagged-edges sometimes seen within an output image by softening it. It typically improves the quality of a scaled image greatly.
1T-C2 SERIES OPERATION MANUAL In ‘Pixel’ mode, the user has direct access to pixel and line-accurate scaling functions. This lets the user specify the exact co-ordinates and size of the source image (within the video source), and the position and size of where this is placed in the output video signal.
1T-C2 SERIES OPERATION MANUAL 8.4.3 ‘Aspect adjust’ = ‘Pixel’ Adjust windows In [ 300] , 150 750, 400 Adjust windows Out [ 50] , 50 250, 300 These menu items work together to specify the exact co-ordinates and size of the source image (within the video source) and the position and size of where this is placed in the output video signal – in other words the ‘In’ and ‘Out’ positions and sizes.
1T-C2 SERIES OPERATION MANUAL Adjust keyers Swap fore/backgrnd [Off] This menu item is only present on single-channel scalers – dual-channel scalers have the layer priority set within the ‘Adjust Windows’ menu. This menu item allows you to swap the foreground and background images when Lock mode is set to Lock & Mix. It will have no effect in any other mode (since no background is present). Normally, your foreground is the input (window) source and your background is the lock source.
1T-C2 SERIES OPERATION MANUAL sometimes 51%. Increasing the softness value will broaden the range of keyed colors so that the keying of images varies depending on how close a color is to the keyed-out range. Adjust keyers Y Key invert [Off] The Y Key invert changes the keying characteristics with respect to what colors of the foreground image you wish to ‘key out’. Setting it to Off will cause the colour range that’s defined to be removed - remove the desired colors.
1T-C2 SERIES OPERATION MANUAL 8.6.1 Menu items common to all inputs Source: RGB1 Aspect correct [ Fill] This menu item will be used to correct the aspect ratio of the video source when converted into the final output resolution. The following table details what happens in the available modes: Setting Fill (default) Aspect H-fit V-fit 1:1 Result The source is stretched to fill the output. The source’s aspect ratio is maintained on the output.
1T-C2 SERIES OPERATION MANUAL Source: RGB1 OPTION audio source [ 1] If an external audio switcher is connected via the OPTION bus, then this menu item selects the desired Audio input for use with the active video source, allowing an audio-follow-video function. In most situations, the Audio input values would be different for each video source – so that when the first video source is selected, so is the first audio source (this is called ‘audio follow video’).
1T-C2 SERIES OPERATION MANUAL maximum movement within an image. Your unit provides some tools to minimize the effects of de-interlacing of an image. The following options are available for this menu item: Mode Normal/weave Auto Film 3:2 M. Comp Low M. Comp Med. M. Comp High Frame/bob Function The two interlaced fields are simply combined/weaved together. This will often show artifacts on moving images, but can be used when the input is known to be still.
1T-C2 SERIES OPERATION MANUAL If turned ‘On’, and a HDCP-compliant display or device is attached to your unit’s DVI output, then HDCP encrypted sources can be used. The following table summarizes the message given in brackets: Status message Inactive Active Description Effect HDCP is not active at the DVI connector. HDCP is active at the DVI connector. HDCP-encrypted material cannot be received by the unit.
1T-C2 SERIES OPERATION MANUAL If you change this value, you’ll need to store your settings and then re-boot the CORIO2 unit at least once to ensure that the DVI source sees that the EDID data has changed. It should also be noted that some graphic cards will require your PC to be rebooted before they see that a change has occurred.
1T-C2 SERIES OPERATION MANUAL pixel phase adjustment allows you to change the position (from 0 to 31) where the pixels are sampled, relative to the horizontal sync signal. To make this adjustment, select an RGB source and then provide an image from that source with fine detail, preferably with very sharp vertical lines. Adjust this value until you see the sharpest image. Alternately, adjust this value to give the worst (noisiest/softest) image, and then add or subtract 16 to get the optimum value.
1T-C2 SERIES OPERATION MANUAL Saturation is the amount of color present in the image. Hue is the color “tint” parameter and the adjustment range is +90 degrees through to -90 degrees with 0 being the default. Source: YC1 Sharpness [0] Within limits, you can enhance or soften the appearance of detail within an image. The Sharpness values go both negative and positive, with 0 being the default.
1T-C2 SERIES OPERATION MANUAL Important Cautionary Information DO NOT ADJUST THESE ITEMS UNLESS YOU’RE CERTAIN YOU KNOW WHAT YOU’RE DOING! THE ONLY METHOD TO UNDO CERTAIN CHANGES IS TO UPDATE THE FIRMWARE. TRY USING THE AUTOSET, SHRINK, SHRINK POS, TL & BR ADJUSTMENTS FIRST. Making adjustments here risks creating a non-standard resolution that is not displayable on a monitor. The resolutions and values within the database are industry standards and should not normally be altered by the user.
1T-C2 SERIES OPERATION MANUAL The H.freq.fine (Horizontal Sync Frequency) adjustment provides the option for changing the Horizontal Sync timing Frequency in 1 Hz steps. Use this option to fine tune after using the course adjust. Please note that the internal sync generator may be unable to generate the exact frequency you want. 800 x 600 60 Hz Clks/l [1056] = 40.000MHz This option changes the total number of image pixels on one line of monitor video including the Horizontal sync pulse and blanking time.
1T-C2 SERIES OPERATION MANUAL respect to the Horizontal Sync pulse and the width of the Back Porch have a direct bearing on where the active (visible) portion of the image begins. Do not attempt this adjustment without monitoring the results with an oscilloscope. 800 x 600 60 Hz H/V Sync [ 128] x 4 There are standards for all current computer and broadcast resolutions that specify the correct width of both Vertical and Horizontal synchronizing pulses.
1T-C2 SERIES OPERATION MANUAL The first section, “SW”, is the version of the software that is installed on your unit. You can update software via the User Support web site (procedure to be described later in this manual) and the updates are currently free of charge. “PT” refers to Product Type and “BT” means Board Type. Both of these are hardware designators and cannot be changed by the user however both designators are important to support personnel.
1T-C2 SERIES OPERATION MANUAL of the screen edge between Low, Medium, High and V.high. Medium is the default level, which is recommended for normal use (Windows-type images, etc.) System OSD on power up [On] This parameter controls whether the ‘welcome’ screen is displayed or not on power up for units with an on-screen display – it can be disabled as required. This is useful when a unit is installed as part of an overall system.
1T-C2 SERIES OPERATION MANUAL System Logos / T-cards 1 / 4 If your units supports Logos or Still Images / Testcards then this screen will display how many are present in the memory of the units. System Power cycles 41 Power Cycles refers to how many times the unit has been powered since it left the factory. This is an informational screen.
1T-C2 SERIES OPERATION MANUAL 48
1T-C2 SERIES OPERATION MANUAL 9 RS232 PORT 9.1 Connection Your unit is fitted with a standard ‘D9’ plug or socket allowing it to be controlled from a computer or other type of terminal or console with a similar interface. Most computers fitted with an RS232 port, known as a ‘COM’ port, will have a ‘D9’ plug on them.
1T-C2 SERIES OPERATION MANUAL 10 RS232 / IP CONTROL SPECIFICATION PLEASE NOTE: Not all units support RS232 and/or IP (Ethernet) communications – check to see if this feature is present on your unit. This section outlines how to control a unit via an RS232 or Ethernet link (if fitted to your unit), using ASCII-based commands. It details how to send and receive serial data to perform many of the functions that a user has access to on the unit.
1T-C2 SERIES OPERATION MANUAL The ACK flag will be returned as 0 if the command is invalid for some reason – for example a bad FUNCTION, WINDOW, OUTPUT or PAYLOAD value. An ACK=0 message will be otherwise identical to the one you sent, so you know exactly which message has the error. Any changes made to the unit using the front panel controls will also cause the full 20 byte message to be sent indicating the change that has occurred, thus enabling a program to stay ‘in-sync’ with the unit.
1T-C2 SERIES OPERATION MANUAL CHA (Channel) SOURCE returned means message was okay. ACK=0 returned means an error was present in the message. Bit 5 = 0 Reserved for future use. Bit 4 = 0 Reserved for future use. Bit 3 = 0 Reserved for future use. Bit 2 = 1 This bit *must* be set. Bit 1 = 0 Reserved for future use. Bit 0 = 0 Reserved for future use. This byte has multiple uses, and defaults to 0 unless used for: CHA When a channel number is used in the Adjust Sources section (see later).
1T-C2 SERIES OPERATION MANUAL CS ASCII-hex byte that is the (check) sum of all previous bytes (excluding the SOP 'F' character). E.g. The command F0400410082000001C8 has the checksum of 04+00+41+00+82+00+00+01=C8, so the complete command to send is F0400410082000001C8. A short-cut for debugging allows the checksum to be replaced by 2 question marks, so in the previous example you could send F0400410082000001?? Instead.
1T-C2 SERIES OPERATION MANUAL Adjust outputs Output enable Lock source (connector) 170 149 Lock method 10A Lock H Shift Lock V Shift Output resolution Output image type analogue 14A 14B 083 0E2 Output image type digital 16C HDCP required HDCP status 233 234 Background Y Background U Background V SDI optimization Output Standard 13B 13C 13D 197 101 Output CV/YC IRE Output CV/YC Hue (degrees) Output SC/H Phase Output Luma Bandwidth Output Chroma Bandwidth Output Chroma delay PAL WSS 133 139 0=B
1T-C2 SERIES OPERATION MANUAL Take 11E Audio amp. Volume AES/SDI Chan. 1 source AES/SDI Chan. 2 source AES/SDI Chan. 3 source AES/SDI Chan. 4 source AES/SDI Chan. 5 source AES/SDI Chan. 6 source AES/SDI Chan. 7 source AES/SDI Chan.
1T-C2 SERIES OPERATION MANUAL In (top-left H) In (top-left V) In (H size) In (V size) Out (top-left H) Out (top-left V) Out (H size) Out (V size) Aspect change Aspect adjust Flicker reduction Image smoothing Image flip Temporal interpolation Max fade level Fade out / in 21B 21D 21C 21E 21F 221 220 222 190 102 092 0A1 095 229 10F 193 Layer priority Headphone volume Audio vol. (volume) Audio vol. (on/off) 144 0FD 206 207 0..2 = Normal, Letterbox, Pillarbox 0..1 = Simple, Advanced 0..
1T-C2 SERIES OPERATION MANUAL E.blnd gamma H E.blnd gamma V E.blnd comp cent E.blnd comp side 188 18D 198 19D 1..150 1=0.01, 150=1.50 1..150 1=0.01, 150=1.50 0..99 0..99 Logos (on certain models only) Logo enable Logo number H/V out shift (H) H/V out shift (V) Max fade level Layer priority 12B 143 0AD 0AE 10F 144 0..1 = Off, On 0..9 Logo selection 0..100 % 0..100 % 0..100% 0..
1T-C2 SERIES OPERATION MANUAL Audio vol Bal On source loss (was Deglitch) Source stable (read only) Input pixel phase RGB input type 10..FF 0CF 10..FF 0D1 10..5F 0A3 RGB contr. (red) RGB contr. (green) RGB contr. (blue) YUV setup level De-int. 10..1F 10..1F 10..1F 10..1F 10..FF 22A 10..5F 091 10..1F 0C1 0C5 0C6 0C7 23E 0B8 (Film mode detected) 10..FF 0E3 Diagonal interpolation 10..FF 22B Noise reduction 10..5F 23F Bright 30..5F 0BB Contrast 30..5F 0BC Saturation 30..5F 0B9 Hue 30..5F 0BA Sharpness 30.
1T-C2 SERIES OPERATION MANUAL Switching fade time Wipe type 0F5 145 Wipe Size 146 Audio Control (S2-106AD Only) Sample frequency 191 Audio delay 192 0 (off) to 50 (5.0 seconds) 0 = Left -> Right 1 = Right -> Left 2 = Up -> Down 3 = Down -> Up 4 = Diagonal 5 = Diamond 10..2000 0..4 = Bypass, 32, 44.1, 48, 96kHz 0..
1T-C2 SERIES OPERATION MANUAL Resolutions Number of Still Images / Testcards Number of logos Board temp. (deg.C) Air temp. (deg.C) Regulators temp.(deg.C) PLD temp. (deg.C) Fan speed (rpm) Led brightness LCD backlight RS232 Baud rate 0D8 0D9 Read only Read only 14F 0CD 148 147 111 0CE 12C 200 0AB TAC number 0 TAC number 1 TAC number 2 TAC number 3 TAC number 4 TAC number 5 MAC number (IP port) 15D 15E 15F 160 161 162 208 Read only Read only Read only Read only Read only Read only 0..100 0..
1T-C2 SERIES OPERATION MANUAL F 42 00 86 - 00 86 000064 70 CR Set baud to 9600 F 04 00 42 00 AB 000000 F0 CR Reply is at 9600 baud F 44 00 42 00 AB 000000 30 CR Set 1A Zoom = 300 F 04 00 42 00 86 00012C F7 CR F 44 00 42 00 86 00012C 37 CR Set 1A Shrink to 50 F 04 00 42 00 87 000032 FE CR F 44 00 42 00 87 000032 3E CR Set 1A Shrink H Posn to 0 F 04 00 42 00 DA 000000 1F CR F 44 00 42 00 DA 000000 5F CR Set 1A Shrink V Posn to 100 F 04 00 42 00 DB 000064 84 CR
1T-C2 SERIES OPERATION MANUAL Read number of items currently stored in Preset 2 read F 84 01 42 00 F4 BB CR Returned packet indicates 4 items available to F 44 01 42 00 F4 00002 FC CR Read the Function for the first item in the preset / macro F 84 01 42 00 F3 BA CR Payload is the Function stored – 86 = Zoom Read the Data for the first item in the preset / macro F 84 01 42 00 F2 B9 CR Payload is the data for the function – 100% F 44 01 42 00 F2 000064 5D CR Read the Function for the second item
1T-C2 SERIES OPERATION MANUAL SOP CMD CHA WIN OUT FUN PAY Restore F 04 CS EOP SOP CMD CHA WIN OUT FUN PAY CS EOP 05 42 00 F1 000000 3C CR F 44 05 42 00 F1 0000 00 7C CR Run macro 1 F 04 00 42 00 F1 000000 37 CR F 44 00 42 00 F1 0000 00 77 CR Run macro 2 F 04 01 42 00 F1 000000 38 CR F 44 01 42 00 F1 0000 00 78 CR Run macro 3 F 04 02 42 00 F1 000000 39 CR F 44 02 42 00 F1 0000 00 79 CR Run macro 7 F 04 07 42 00 F1 000000 39 3E F 44 02 42 00 F1 0
1T-C2 SERIES OPERATION MANUAL 11 COMMON OPERATIONS This section provides step by step instructions for some common operations. 11.1 Operation of the Keyer Some units come equipped with a very powerful Luminance and Chrominance Keyer.
1T-C2 SERIES OPERATION MANUAL to decrease the ‘min’ values and increase the ‘max’ values to broaden the range of colors keyed out. At this point, only the key color should remain transparent.
1T-C2 SERIES OPERATION MANUAL 12 TROUBLESHOOTING AND TECHNICAL SUPPORT If problems are experienced, please read through the symptom topics below in order to resolve the problem. After doing so, if you still need to, contact Technical Support at http://www.tvone.com/support. Please have the following details of the problem handy: Whether the problem happens only at specific times or has only just started occurring (and what other things have changed at the same time).
1T-C2 SERIES OPERATION MANUAL 12.4 There is excessive flicker on the Output. Try using a different Flicker reduction mode. Turning the contrast down and the brightness up on the output device can have a large effect on flicker. Or try adjusting the brightness and contrast of the source input by selecting the Input adjust menu. 12.5 The Output image is distorted. This may occur where some of the areas of the image are very dark and others are very bright.
1T-C2 SERIES OPERATION MANUAL 12.11 The RGB input is selected but the image is rolling or pink. Check the Adjust sources menu and confirm that the input type and sync method is set correctly. (Having YUV input selected, instead of RGBHV often causes this problem). 12.12 The video signal from my DVD player does not appear to work. Some DVD players have a switch at the back that selects between ‘Component’ and ‘S-Video’ output, because most will not let you output both at the same time.
1T-C2 SERIES OPERATION MANUAL 13 RETURN PROCEDURE Before returning your unit for repair, there are several checks you can make yourself to make sure the problem is actually caused by a failure. 13.1 Are you sure there's a fault? Many 'faults' are due to incorrect set-up or use so a simple checklist is provided below to help you identify potential problems. Set the unit up with your equipment as described in this manual and run through the checklist.
1T-C2 SERIES OPERATION MANUAL Please clearly state the return number on the outside packaging and on any accompanying documentation. This will greatly speed up processing. IMPORTANT: DO NOT return a unit for warranty repair without first obtaining a Return Authorization Number. No action will be taken on a unit returned in warranty for repair without a Return Authorization Number.
1T-C2 SERIES OPERATION MANUAL 14 WARRANTY POLICY LIMITED WARRANTY – With the exceptions noted in the next paragraph, TV One warrants the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should this product, in TV One’s opinion, prove defective within this warranty period, TV One, at its option, will repair or replace this product without charge.
1T-C2 SERIES OPERATION MANUAL 15 CONNECTOR PINOUTS 15.1 HD15 connector 5 10 15 1 6 11 1. Red / Pr / R-Y 2. Green / Y 3. Blue / Pb / B-Y 4. ID2 (input & output linked) 5. GND 6. GND 7. GND 8. GND 9. No connection 10. GND 11. GND on input, pulled high on output (used for auto-termination) 12. SDA (input & output linked) 13. H sync (or composite sync for RGBS) 14. V sync 15. SCL (input & output linked) 15.2 RS232 / D9 socket 16. N/C 17. TX (Transmit data) 18. RX (Receive data) 19. N/C 20.
1T-C2 SERIES OPERATION MANUAL 16 SPECIFICATIONS See product front and rear diagrams for details of product I/O. Not all units in the series have all the inputs and outputs listed here. 16.
1T-C2 SERIES OPERATION MANUAL PC Resolutions: any up to 2048x2048 (user adjustable) HDTV Resolutions: any up to 1080p Vertical Refresh Rate: any to 250Hz 16.
1T-C2 SERIES OPERATION MANUAL 16.10 Power Requirement External power supply: 12V DC @1A maximum. Actual current consumption varies between units. Internal over-voltage & over-current protection. Full PSU specification: 12v DC regulated 1Amp PSU with a 2.5mm locking centerpin positive DC power connector. A non-locking 2.5mm DC power connector will also fit. 16.
1T-C2 SERIES OPERATION MANUAL 17 CONTACT INFORMATION Should you have and questions or require assistance with this product in areas not covered by this manual, please contact TV One at the appropriate location shown below: TV One USA 2791 Circleport Drive Erlanger, KY 41018 USA Tel 859-282-7303 Fax 859-282-8225 sales@tvone.com www.tvone.com TV One Europe Continental Approach Westwood Industrial Estate Margate, Kent CT9 4JG, UK Tel +44 (0)1843 873311 Fax +44 (0)1843 873312 sales.europe@tvone.com www.