Safety Instructions

ManualsBrandsTurnils North America ManualsElectronicsAMP Remote

AMP25B

Instruction

Attention

-1-

The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.

Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.

Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Declarations

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

-2-

Safety

1. Do not expose motor to humid, damp or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna and keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If power cable or connector is damaged, do not use.

6. Ensure correct crown and drive adaptor are used.

7. Ensure power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls shall be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered

operation.

11. Installation and programming to be performed by a qualified professional, use or modification outside

the scope of this instruction may void warranty.

Features

Fields of Application

Specifications

Following data for reference

Working temperature: -10℃ ~ +50℃

Input Voltage: USB 5V 1A / USB 5V 2A

Radio Frequency: 433.925MHz

Maximum Running Time: 6 minutes

Model

Rated Torque

(N.m)

Rated Speed

(rpm)

Rated Power

(W)

AMP25B - 0.7/34 0.7 34 8

AMP25B -1.1/28 1.1 28 8

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management.

Max power input for recharging: 5V 2A.

Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .

During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and

needs to be charged.

During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped

running and needed to be recharged.

Rechargeable Battery

Blinking red:

Low battery alert

Blinking green:

Charging is processing

Solid green:

Battery has

finished charging.

FCC Text - text 01

Add A zoom in on the

charging port

P1 Button Instructions

P1 button

Lithium Battery Switch

LED light

Micro-USB Port

Add visual explanation of P1 - file 02

Sheer

Roller

Revolve

Roman shades

Issues Possible Causes Solution

Battery in motor is depleted

Recharge with compatible AC adaptor and check

connection and positioning of solar PV panel

Insufﬁcient charging from Solar

PV Panel

Check connection and orientation of solar PV panel

Remote control battery is discharged Replace battery

Battery is inserted incorrectly into

remote control

Check battery polarity

The motor has no response Radio interference / shielding

Ensure remote control and the antenna on the motor are

positioned away from metal objects

Receiver distance is too far from

Remote Control

Move remote control to a closer position

Power failure Check power supply to motor is connected and active

Incorrect wiring

Check that wiring is connected correctly (refer to motor

installation instructions)

Motor beeps 10 times when in use

Battery voltage is low / PV (solar

panel issue)

Recharge with AC adapter or check connection and

positioning of solar PV panel

Always reserve an individual channel for programming

functions

SYSTEM BEST PRACTICE - Provide an extra 15 channel

remote in your multi-motor projects that provides

individual control for each motor for programming

purposes

Place all other motors into sleep mode (Press “P1”

button (about 6 sec) on the motor head until motor jog

x2 and beep x2).

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

Cannot program a single motor

(multiple motors respond)

Multiple motors are paired to the

same channel.

Settings Steps

1 Pairing P1 (hold down for 2s) > Stop (hold down for 2s)

2 Switch Rotating Direction Up + Down (hold down for 2s)

3 Setting Upper & Lower Limits

4 Add / Remove Favorite Position P2 > Stop > Stop

5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) > Stop

6 Adjust Limits

7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new)

8 Speed Regulation

Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s)

Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s)

Acceleration: P2 > Up > Up

Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s)

Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s)

Deceleration: P2 > Down > Down

AMP

™

Remote

Declarations

Fields of Application

Quick Index

Safety Instructions

Troubleshooting

Button Instructions

Replace/Install CR2450 Battery

Advanced Setting - Disable Limit Setting

1. Do not expose motor to humid, damp, or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna. Keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If the power cable or connector is damaged, do not use.

6. Ensure the correct crown and drive adaptor are used.

7. Ensure the power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls should be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.

11. Installation and programming should be performed by a qualiﬁed professional. Use or modiﬁcation outside the

scope of these instructions may void warranty.

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the

device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Switch

AMPTILT

AMP25B / AMP28B /

AMP35B / AMP25BDC

AMPCEL

P1 Button

LED light

P1 button

Lithium Battery Switch

Power line

Signal line

P1 Button

Voltage

3V (CR2450)

Radio Frequency

433.92 MHz Bi-directional

Transmitting Power

10 milliwatt

Operating Temperature

14°F to 122°F (-10°C to 50°C)

RF Modulation

FSK

Lock Function

Yes

IP Rating

IP20

Transmission Distance

up to 200m (outdoor)

Specications

a. Remove the cover from the backside of remote,

the lock switch is in the right corner.

b. Move the switch to the “Lock” position to disable

the following commands, remote will show “L” (lock):

- Change Motor Direction

- Setting the Upper and Lower Limit

- Adjust Limit

- Roller Mode or Sheer Mode

c. Move the switch to “Unlock” position to assess all

remote functions, remote will show “U” (unlock).

Switch

Lock

Unlock

*This advanced feature is intended to be used after

all shade programming is completed. User Mode will

prevent accidental or unintended changing of limits.

Please scan QR code to see more

AMP

™

product information

click

Battery

(CR2450)

a. Gently insert the included ejector tool into the

small pinhole opening and apply a small amount

of pressure to the cover and slide the cover off.

b. Install battery (CR2450) with positive (+) side

facing up.

c. Gently slide the cover back on until a “click”

sound is heard.

One-Way

Left Stack

One-Way

Right Stack

Two-Way

Split Stack

Cellular/Honeycomb

Standard

Cellular/Honeycomb

Skylight

Tilt-Only

Horizontal

Narrow

Width

Roller Sheer Banded Roman

Summary of content (2 pages)

PAGE 1
AMP™ Remote Declarations U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
3.2 Set Lower Limit Channel Options Select A Channel a. Press “<” button on the remote to select a lower channel. b. Press “>” button on the remote to select a higher channel. Hide Unused Channels a. Press and Hold (about 3 sec) “<” and “>” buttons simultaneously until remote control displays “C” (channel). a. Action on Remote Control b. Lower Channel Higher Channel 1 15 Remote Response a. Action on Remote Control + Lower Channel b.