T240 A C / D C 10A Touch Charger
TABLE OF CONTENTS INTRODUCTION 02 SPECIFICATION 03 CAUTION and NOTES 04 BATTERIES INFO and MAX CHARGE CURRENT 05 MAIN MENU INFO 06 PROGRAM OF LiPo/Lilo/LiFe/LiHV 07 PROGRAM OF NiMH/NiCd 10 PROGRAM of PB (lead-Acid) 12 PROGRAM OF SMART 14 PROGRAM OF SETTINGS 15 PROGRAM OF MONITOR/CALIBRATION 16 PROGRAM OF MEMORY 17 ERROR INFORMATION 18 SUPPORT AND SERVICES 19 1
INTRODUCTION Thank you for purchasing the Reaktor T240 charger. Designed for both rookies and professional, this system is extremely versatile for the safety and the best use of your system, please read this manual carefully. 3.2in TOUCH COLOR SCREEN Output port Power Switch AC 100-240V Temp.
SPECIFICATION Product Model: T240 Reaktor AC/DC 10A Touch Charger AC Input Voltage 100-240V DC Input Voltage 11-18V Charge Power AC INPUT (CH1+CH2=150W) DC INPUT (120W*2) Charge Current 0.1-10A*2 Discharge Current 0.1-2A*2 LiIon/LiPo/Lilo/LiFe/LiHV 1-6cells*2 NiCd/NiMH 1-15cells*2 PB 2-20V*2 Smart Battery I/II/III*2 Net Weight 0.
CAUTION and NOTES This charger is ONLY suitable for charge rechargeable LiPo, LiFe, LiHV, NiCd, NiMH, Smart and Pb batteries. Do not attempt to charge dry cells, charge other types of batteries may cause fire or explosion. Set up the Input Power Limit/Low Input VOLT Cutoff correctly in the USER SETTING of the DC power supply. Pay attention to the charger during use. Do not leave the charger unattended. Never charge the dead or damaged batteries.
BATTERIES INFO and MAX CHARGE CURRENT Battery Type LiHV LiPo LiIo LiFe NiMH / NiCd No. of Cells Rated Voltage (V) 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 7 8 3.8 7.6 11.4 15.2 19.0 22.8 3.7 7.4 11.1 14.8 18.5 22.2 3.6 7.2 10.8 14.4 18 21.6 3.3 6.6 9.9 13.2 16.5 19.8 1.2 2.4 3.6 4.8 6 7.2 8.4 9.6 5 Charging Current (A) 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.
Battery Type NiMH / NiCd Pb Charging Current (A) No. of Cells Rated Voltage (V) 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 10.8 12 13.2 14.4 15.6 16.8 18 2 4 6 8 10 12 14 16 18 20 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 0.1 - 10.0A 11 12 22.0 24.0 0.1 - 10.0A 0.1 - 10.0A LiPo Voltage Level : 4.2V/Cell Max Charge Voltage : 3.
MAIN MENU INFO CH1 CH2 T240 LiPo LiFe Lilo LiHV NiMH NiCD PB Smart SETTING MEMORY MONITOR CALIBRATION Main Menu Touch System Controller 3.2 Inch Touch Screen Security Settings Memory : Save Six operation data Battery Management, Checking Battery Capacity, Voltage, Balancer Calibrate Charger NOTE: Please read carefully before doing anything!! CH1 CH2 means CH-2 or CH-1 Swift image. Note: 1. Two Channel are independent, and you can use different mode to operate . 2.
PROGRAM OF LiPo/Lilo/LiFe/LiHV Please replace this instruction as below: Instruction for charging LiPo, Lilo, LiFe, LiHV, please follow the below steps: Step 1: Select Channel and Select Battery Type on the menu (Image 1) Step 2: Select and adjust you desire battery related parameters (image 2) Step 3: Select “ Start” operation will begin (image 3) CH1 CH2 T240 CHARGE STORAGE 1 LiFe Lilo LiHV NiCD PB Smart DISCHARGE End voltage Battery Cell LiPo BALANCE CHARGE Int.
WORKING INTERFACE CH1 LiPo(6S) BAL Charge 00:20:09 Ext.Temp: No Sensor Int.Temp: CH2 CH1 CH2 LiPo(6S) BAL Charge 25 CC Input Vol: 14.73V Voltage: 23.12V 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 80% 80% 80% 80% 80% 80% Current: 0.60A Capacity: 5mAh 3 NOTE: 1. Image 3 show the graphic photo for LiPo Charging current and voltage. 2. Image 4 show each cell voltage and percent during LiPo charging. 3. Image 3 show all setting data for LiPo Charging.
PROGRAM OF NiMH/NiCd Instruction for charging NiMH please follow the below steps: Step 1. Enter to Menu, Select Battery Type (Image 8) Such as: NiMH, Enter into “SET PARAMETER FOR NiMH BETTERY” (Image 9) Step 2. Select “CHARGE” MODE, And set the related parameters (Image 9) CH1 CH2 T240 DISCHARGE CHARGE CYCLE 2 Delta v Battery Cell LiPo LiFe LiHV Lilo 15S Charge Current NiMH 1 SETTING NiCD PB Smart MEMORY MONITOR CALIBRATION 1.5A MORE...
WORKING INTERFACE Step 4. Select previous data to START (Image 11) to Discharge (Image 12), or touch BACK icon into previous step (Image 9), and touch START to charge. (Image 12) WORKING INTERFACE CH1 NiMH(15S) Charge 00:00:09 Ext.Temp: No Sensor Int.Temp: CH2 25 CC Input Vol: 14.73V Voltage: 22.2V Current: 0.60A Capacity: 5mAh CH1 CH2 means CH-2 or CH-1 Swift image Note: 1. If CH-2 has been not used, CH2 press image, return back to main menu, and use CH-2 operation. 2.
PROGRAM of PB(lead-Acid) Instruction for charging Pb please follow the below steps: Step 1: Select Channel and Select Battery Type on the menu (Image 13) Step 2: Select and adjust you desire battery related parameters (image 14) Step 3: Select “ Start” operation will begin (image 13) CH1 CH2 T240 CHARGE TRICKLE Battery Cell LiPo LiFe LiHV Lilo 6S Charge Current NiMH NiCD PB Smart 5A 1 SETTING MEMORY MONITOR DISCHARGE 2 Delta v 2.
WORKING INTERFACE Step 4. Select previous data to START (Image 16) to balance charging (Image 17), or touch BACK icon into previous step (Image 16), and touch START to balance charge (Image 17) WORKING INTERFACE CH1 PB(6S) Charge 00:20:09 Ext.Temp: No Sensor Int.Temp: CH2 25 CC Input Vol: 14.73V Voltage: 23.12V Current: 0.60A Capacity: 5mAh Note: 1. Image 17 show the graphic photo for LiPo Charging current and voltage. 2. Image 17 show each cell voltage and percent during LiPo charging. 3.
PROGRAM OF SMART Instruction for charging Smart Battery please follow the below steps: Step 1: Select Channel and Select Battery Type on the menu (Image 1) Step 2: Select and adjust you desire battery related parameters (image 2) Step 3: Select “ Start” operation will begin (image 3) CH1 CH2 T240 LiPo LiFe Smart I (11.1V/3S) Smart II/IV (15.2V/4S) LiHV Lilo CH1 SMART BATTERY Max voltage 26.1V Max current NiMH NiCD PB Smart III (22.8V/6S) Smart 1 4.
PROGRAM OF SETTINGS Step 1. Enter to Menu, Select Setting (Image 21), into set interface. (Image 22-24) CH1 CH2 T240 LiPo LiFe Lilo LiHV NiMH NiCD PB Smart MEMORY MONITOR CALIBRATION 1 SETTING CH1 SETTINGS PUBLIC SETTINGS Set the volume of the buzzer. Keep Beep default: Middle, Low/ Middle/High/Off optional CH2 SETTINGS In this menu, you can set the cutoff input voltage of the power supply of the charger to protect your power supply.
PROGRAM OF MONITOR/CALIBRATION ONE: Enter into Menu, select Monitor (Image 25) and into BATTERY MONITOR (Image 26) CH1 CH2 T240 LiPo LiFe Lilo LiHV NiMH NiCD PB Smart SETTING MEMORY MONITOR 1 CH1 CH2 BATTERY MONITOR CH1 CH2 BATTERY MONITOR 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 4.05V 8m 8m 8m 8m 8m 8m 80% 80% 80% 80% 80% 80% BALANCE CALIBRATION 1 1) Meter LiXx (LiPo/Lilo/LiFe/LiHV) battery status.
PROGRAM OF MEMORY Step 1. Enter into Menu, select Memory (Image 31) Step 2. Select correct icon as exact battery typeimage 32, and select “Modify” icon, (Image 33) CH1 LiPo NiMH CH2 T240 LiFe Lilo NiCD PB LiHV Smart Pb 6S Charge Curr: 5.0A TVC:4.36V/S NiCd Auto BAL Charge Curr: 1.5A Delta:7mv/s LiPo Auto BAL Charge Curr: 5.0A TVC:4.20V/S LiPo Auto BAL Charge Curr: 5.0A TVC:4.20V/S MODIFY SETTING MEMORY MONITOR CHARGE TRICKLE DISCHARGE End voltage Battery Cell 4.
ERROR INFORMATION The charger will send out an alert and pop-up window if the battery packs setting is incorrect (Image 38). Input voltage is higher than 30V, check the power supply, then restart the charger Input voltage is lower than the value of LOW INPUT VOLTAGE CUT-OFF, check the power supply, then restart the charger. Reverse polarity, check the connection between the charger and the battery, correct the connection, then restart the work.
SUPPORT AND SERVICES WARRANTY Hobbyking provide a period of one year product warranty from the date of purchase. The warranty only applies to material or operational defects, which are present at the time of purchase. During that period we will repair or replace free of service, charge for products deemed defective due to those causes.
