Installation Instructions

ManualsBrandsTurn of the Century ManualsCeiling Fan Lights2-Light Wicker and Oil Rubbed Bronze Ceiling Fan Light Kit with Alabaster Bowl

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless

additional support is provided for the fan.

355-3151

121017

Turn of the Century

355-3151 --- Page 1

Ceiling Fan

Coupling

Pull Chain

Glass Shade

Hex Nut

Rubber Pad

Metal Pad

Cover

Finial

Bulb Type A15

Max.60W (included)

Hex Nut

Short Nipple

Installing the fan light on fans with Non-Removable

switch box:

WARNING:

As per EPACT 2005 requirements, this fan light has a built-in current

limiting device to conserve energy. The fan light will not operate if the

combined wattage of the installed bulbs exceeds 190 Watts. If the fan

light shuts off shortly after being switched on, it may be due to

excessive current demand. You should replace the light bulbs with

lower wattage bulbs.

1. Unscrew the three screws from the switch box, remove

the switch box cover and disconnect the wire nuts.

(See Fig. 1)

2. Push the center plug from inside the switch box cover

to remove the center plug. (See Fig. 1)

Note: Save the center plug should you choose to

remove the light fixture in the future.

3. Feed the two wires from the ceiling fan light through

the center hole in the switch box cover, and thread the

wires through the washer and hex nut, then secure

switch box cover onto the ceiling fan light with a hex

nut and washer. (See Fig. 2)

4. Connect wires by using the wire nuts: (See Fig. 2)

---The black (hot) wire from ceiling fan light to the

black (hot) wire from the fan.

---The white (neutral) wire from ceiling fan light to

the white (neutral) wire from the fan.

---Carefully put wires back into the switch box.

5. Restore the switch box cover back to the switch box

by using the three screws. (See Fig. 2)

6. Install bulbs (included). See relamping label at socket

area or packaging for maximum allowed wattage. (See Fig. 2)

7. Slip the short nipple up through the pull chain, and secure it into the coupling with hex nut.

(See Fig. 2)

8. Slip the glass shade up through the pull chain and the short nipple, secure them with a

rubber pad, metal pad and hex nut. (See Fig. 2)

9. Slip the cover up through the pull chain and the short nipple, secure it with finial.

(See Fig. 2)

10. Turn on the electric circuit.

Motor

Switch Box

Hex Nut

Screw

Switch Box Cover

Nipple

Wire Nut

Washer

Center Plug

----This FAN LIGHT can be installed in one of three ways.

Fig.1.

Switch Box Cover

Screw

Switch Box

Fig.2.

Wire Nut

Summary of content (3 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS 355-3151 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless additional support is provided for the fan. Fig.1.
PAGE 2
Installing the fan light kit on a removable switch box: 1. Unscrew the three screws from the fan, remove the switch box and disconnect the terminals. (See Fig. 3) 2. Push the center plug from inside the switch box to remove the center plug. (See Fig. 3) Save the center plug should you choose to remove the light fixture in the future. 3.
PAGE 3
Installing the fan light on the ceiling: Outlet Box House Grounding Wire Wire Nut hardware package For Semi-Flush 1. Take out the parts from the hardware package For Semi-Flush. (See Fig. 7) 2. Attach two screws to the mounting strap, and secure it with two lock nuts. Adjust the length of the screws if necessary. (See Fig. 7) 3. Attach the mounting strap to the outlet box by using two mounting screws. (See Fig. 7) 4.