User's Manual

ManualsBrandsTsuen Shing Enterprises ManualsElectronicsWinnie The Pooh Baby Phone

The Quick Reference guide is given to provide basic operation of the unit.

Please completely read the user’s guide to take advantage of all the features

this unit has to offer.

QUICK REFERENCE GUIDE

Lights when the

power is on

Built-In Mic

detects sounds

Slide to turn the unit

On or Off

Slide to select a

Channel to

transmit the sound

Insert a 6V Adapter

Antenna

Lights when the

power is on

Lights when sound

is received

Speaker

Rotate to turn the

unit on and adjust

the volume

Lights when the

batteries are low

Slide to select a

Channel to

receive the sound

SIMPLIFIED OPERATION

1. For the Monitor (Transmitter), connect the AC adapter (included) to the DC 6V IN

jack. For the Receivers, connect the AC adapter (included) to the DC 6V IN jack or

insert batteries. Place the transmitter in the same room as the child. Point the micro-

phone toward the crib or play area. Place the receiver(s) in the room where you will

be or if using batteries, connect to your belt using the belt clip.

2. Slide the POWER switch on the transmitter to the ON position; the POWER indicator

will light.

3. Slide the CHANNEL switch on the transmitter to the 1 or 2 position.

4. Slide the CHANNEL switch on one or both of the receivers to the 1 or 2 position to

match the transmitter’s setting made in step 3.

5. Rotate the Power/VOLUME control on one or both receivers counterclockwise until a

click is heard; the POWER indicator will light. Then, adjust the volume as desired.

When a sound is heard, the SOUND LEVEL indicators will light (the more lights, the

louder the sound) and the sound will be heard through the speaker(s). Rotate the

Power/VOLUME control clockwise until a click is heard to turn the unit of

f; the

POWER indicator will turn off.

Summary of content (10 pages)

PAGE 1
QUICK REFERENCE GUIDE The Quick Reference guide is given to provide basic operation of the unit. Please completely read the user’s guide to take advantage of all the features this unit has to offer.
PAGE 2
Dear Customer, Please read this manual thoroughly before operating the unit to become more familiar with it and obtain the performance that will bring you continued enjoyment for many years. Keep these instructions handy for future reference. PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX. For future reference, record the serial number of the unit printed on the rear of the cabinet.
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
TRANSMITTER LOCATION OF CONTROLS 1 2 3 4 5 6 7 8 1. 2. 3. 4. Photo Frame Tabs Photo Frame POWER Indicator MIC 4 5. 6. 7. 8.
PAGE 5
LOCATION OF CONTROLS (CONTINUED) RECEIVERS 1 2 3 5 6 4 7 11 11 12 13 12 8 9 10 1. 2. 3. 4. 5. 6. 7. 8. Antenna POWER Indicator SOUND LEVEL Indicators Speaker Power/VOLUME Control BATT LOW Indicator CHANNEL Switch Release Button 9. 10. 11. 12. 13.
PAGE 6
INSERTING A PICTURE PREPARATION 1 2 Press in on the two Frame Tabs and slightly lift the transparent frame out. Insert a picture, then replace the transparent frame, by positioning the two tabs at the bottom of the frame, and insert properly into the unit. NOTE: If the photo/picture size does not fit the frame, you can use the transparent frame to trace the frame size and cut the photo/picture with scissors. The transmitter is designed to operate on AC household current only.
PAGE 7
PREPARATION (CONTINUED) INSTALLING BATTERIES (FOR RECEIVERS) 1 2 Press and hold the Release button, then rotate the belt clip counterclockwise. Slide out the battery compartment in the direction of the arrow. 3 NOTES: The BATT LOW indicator will light when batteries are low and need replacing. Insert three (3) AAA size batteries, following the diagram. Replace the battery compartment and rotate the belt clip until it locks in place.
PAGE 8
1 OPERATION 2 Connect the unit with the AC adapter and/or insert batteries as shown on pages 6 & 7. Place the transmitter in the same room as the child. Point the microphone toward the crib or play area. Place the receiver(s) in the room where you will be or if using batteries, connect to your belt using the belt clip. Slide the POWER switch on the transmitter to the ON position; the POWER indicator will light. 3 4 Slide the CHANNEL switch on the transmitter to the 1 or 2 position.
PAGE 9
TROUBLESHOOTING GUIDE If you experience a problem with this unit, check the chart below before calling for service. PROBLEM SOLUTION Static or buzzing is heard through the Make sure the CHANNEL switch on the transmitter receiver. and the receivers are set to the same channel. Receiver is out of range of the transmitter. Move closer. Transmitter's POWER indicator is not Make sure the POWER switch is set to the ON lit. position. Make sure the unit is connected to the AC adapter.
PAGE 10
SPECIFICATIONS Power Requirements: Transmitter ...................................................................................DC 6V IN Receiver.....................................DC 6V IN, (DC 4.5V 3 x "AAA" Batteries) Receiver Power Output............................................................................150mW Frequency CH 1................................................................................49.830 MHz Frequency CH 2.................................................................