User's Manual

ManualsBrandsTsuen Shing Enterprises ManualsElectronicsTwo Way Radio with GMRS and FRS

英文 Page 1 of 8

2008-6-19

WT-549 USER MANUAL (full features, US version)

Congratulations

You have just purchased a qualified 2 way radio. Please read this manual carefully

before use for correct operation. You should also handle this manual with care for

future reference.

BUTTONS AND CONTROLS

Main Screen (Fig.1)

1. Operation Mode Indicator

2. Channel Number Display

3. Key Lock Indicator

4. Battery Icon

5. Sub code

6. VOX

7. Channel Scan Indicator

8. Transmission Indictor

9. Reception Mode

CHARGER JACK

EARPHONE/ MIC JACK

NECK STRAP HOLE

Fig.1

5 6

Summary of content (8 pages)

PAGE 1
英文 Page 1 of 8 2008-6-19 WT-549 USER MANUAL (full features, US version) Congratulations You have just purchased a qualified 2 way radio. Please read this manual carefully before use for correct operation. You should also handle this manual with care for future reference. BUTTONS AND CONTROLS CHARGER JACK EARPHONE/ MIC JACK NECK STRAP HOLE Main Screen (Fig.1) 1. Operation Mode Indicator 2. Channel Number Display 3. Key Lock Indicator 4. Battery Icon 5. Sub code 6. VOX 7. Channel Scan Indicator 8.
PAGE 2
英文 Page 2 of 8 Battery Installation 1. Turn off the radio and remove the belt clip. 2. Open the battery compartment door. 3. Insert 3 x “AAA” alkaline batteries according to the anode-cathode signs shown in the battery compartment. 4. Close the battery compartment door. Note: 1. Don’t mixed use new & old, different styles, alkaline & rechargeable and different capacity batteries. 2. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
PAGE 3
英文 Page 3 of 8 B. “Walkie Talkie” Operation Select the same channel as that of your friend’s. e.g. CH=01, SC-38 1. Press MENU key once to enter channel selection menu.(Fig.4.1) 2. Press + or – key to change the channel. 3. Press key to confirm the setting and return the main screen. 4. Press MENU key twice to enter subcode selection menu.(Fig.4.2) 5. Press + or – key to change the subcode. 6. Press key to confirm the setting and return the main screen.
PAGE 4
英文 Page 4 of 8 Function Setup Procedure You may simply set up the function by referring the table below: Function Channel Selection Subcode Selection Auto Channel Scan Monitor Call Tone Key Tone Received all signal in the same channel during weak transmission Call your partner by sending a call tone Activate/inactive the key beep according to your own preference Roger Beep VOX Application Select the channel Select the Scan the channel for communication subcode automatically to identify the occ
PAGE 5
英文 Page 5 of 8 2. Supply power : 7.5V/600mA 3. Charging time is not over 6 hours. A. Recharging by AC / DC adaptor Simply plug the charging adaptor into the charger jack and then turn on the radio, the battery level icon shows while charging until the batteries are fully charged. B. Recharging by desktop charger B1. Plug desktop charger into any nearby standard household electrical outlet. B2. Insert the rechargeable batteries into radio, place them on the desktop charger. B3.
PAGE 6
英文 Page 6 of 8 6 462.6875 14 467.7125 7 462.7125 15 462.5500 8 467.5625 16 462.5750 22 462.7250 Interference Eliminator Code Chart(Hz) Code 1 2 3 4 5 6 7 8 9 10 11 12 13 Frequency 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100 103.5 Code 14 15 16 17 18 19 20 21 22 23 24 25 26 Trouble Shooting Problem No Power Frequency 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 162.2 Code 27 28 29 30 31 32 33 34 35 36 37 38 Frequency 167.9 173.8 179.9 186.2 192.
PAGE 7
英文 Page 7 of 8 - Radio are too far apart. Obstacles interfere with transmission. - Talk range is up to 3 km in clear and unobstructed conditions. Caution: - Please avoid charging for non-rechargeable batteries in the product as charging operation can only be performed with suitable rechargeable batteries. - Please use only supplied accessories or optional accessories produce by our company or it might cause defect or damage to the unit.
PAGE 8
英文 Page 8 of 8 - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.