TSL Reader Range TSL Multi-Technology Card Reader Installation Manual
The specifications and descriptions of products and services contained in this document were correct at the time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated Control Technology Limited.
Contents Introduction 5 About This Module 5 Reader Editions 6 Reader Accessories 8 Faceplates 8 Vandal Resistant Cover 9 Surface Mount Box 9 Pigtail Cables 10 Ferrite Shield 10 MIFARE Technology 11 About MIFARE 11 Secured MIFARE Card Format 11 About MIFARE DESFire EV1 11 About MIFARE DESFire EV2 11 About MIFARE DESFire EV3 12 MIFARE/DESFire Products 12 Installation Requirements 13 Mounting 14 Mounting Instructions 14 Mounting with Vandal Resistant Cover Accessory 16 M
Enabling Wiegand Mode 29 Programming the Card Reader 30 Protege Config App 30 Technical Diagrams 31 TSL Standard Reader 31 TSL Extra Reader 32 TSL Mini Reader 33 TSL Standard Reader Vandal Resistant Cover 34 TSL Extra Reader Vandal Resistant Cover 35 Technical Specifications 36 New Zealand and Australia 39 European Standards 40 UK Conformity Assessment Mark 41 UL and ULC Installation Requirements 42 CAN/ULC-S319 42 UL 294 42 FCC Compliance Statements 43 Industry Canada Stat
Introduction This installation manual provides instructions and technical specifications for physical installation of the ICT TSL Multi-Technology Card Reader. For programming information, see the ICT Card Reader Configuration Guide, available from the ICT website.
Reader Editions The TSL Multi-Technology Card Reader comes in multiple sizes and with a range of optional features. Standard 117 x 43 x 9.5mm (4.61 x 1.69 x 0.37") Keypad 125kHz MIFARE/ DESFire/ NFC Bluetooth® Technology TSL-STD-RR-HL TSL Standard Multi-Technology Card Reader with Bluetooth® Wireless Technology TSL-STD-RK-HL TSL Standard Multi-Technology Card Reader with Bluetooth® Wireless Technology and Keypad TSL-STD-RR-H TSL Standard 13.
Mini 87 x 43 x 9.5mm (3.43 x 1.69 x 0.37”) Keypad 125kHz MIFARE/ DESFire/ NFC Bluetooth® Technology TSL-MINI-RR-HL TSL Mini Multi-Technology Card Reader with Bluetooth® Wireless Technology TSL-MINI-RR-H TSL Mini 13.
Reader Accessories A number of optional accessories are available to complement your TSL reader installation. Faceplates All TSL readers are shipped with a black faceplate. To switch to a white reader simply order a white faceplate. Whether you're looking for a color change or need to replace a damaged cover, replacement white and black faceplates are available to suit all TSL reader sizes and configurations.
Vandal Resistant Cover The vandal resistant cover (VRC) accessory is ideal for locations where a card reader may be exposed to damage, including corridors, parking buildings, correctional facilities, and other public places. Highly resistant to impact, such as from the swing of a hammer or baseball bat, its robust construction provides greater durability and protection against vandalism and malicious damage. The flush design also serves as an anti-ligature measure for an additional level of safety.
Pigtail Cables TSL readers use a shielded 8-wire pigtail wiring loom with a Hirose socket plug for connection to the reader. A standard 34cm cable is supplied with the reader, while a 3.5m long cable option is also available. P UL ULC The 3.5m pigtail cable is not compliant for UL/ULC installations. Ordering Codes Accessory Ordering Code Standard 34cm TSL Reader Pigtail Cable TSL-CABLE-34CM 3.5m TSL Reader Pigtail Cable TSL-CABLE-3.
MIFARE Technology About MIFARE Based on the international standard ISO/IEC 14443 Type A, MIFARE is a technology used for contactless RFID smart card systems consisting of card and reader components.
About MIFARE DESFire EV3 The latest addition to the MIFARE DESFire product family, MIFARE DESFire EV3 offers even more advanced hardware and software implementation on a brand new internal chip, and combines enhanced performance with a greater operating distance and improved transaction speed compared to its predecessors.
Installation Requirements This equipment is to be installed in accordance with: ⦁ The product installation instructions ⦁ UL 681 - Installation and Classification of Burglar and Holdup Systems ⦁ CAN/ULC-S302, Installation and Classification of Burglar Alarm Systems for Financial and Commercial Premises, Safes and Vaults ⦁ The National Electrical Code, ANSI/NFPA 70 ⦁ UL 827 - Central-Station Alarm Services ⦁ CAN/ULC-S301, Central and Monitoring Station Burglar Alarm Systems ⦁ CAN/ULC-S561, Insta
Mounting The card reader provides the reading component of access control, time and attendance and alarm systems. It is intended to be mounted on a wall with adequate air flow around and through it. Mounting Instructions Cables are intended to be run inside the wall. If cables are to be run through external conduits you must use the surface mount box accessory (see page 18). 1. Select where to mount the card reader, ensuring it is mounted a minimum of 1.1m (3.
Screw heads must not protrude above the mounting hole cavity Moun✁ng screws Connec✁on socket Accessories Provided ⦁ 1 x shielded 8-wire wiring loom with waterproof Hirose socket plug ⦁ 1 x M3(G4)x4 PanPozi Plastite SS316 stainless steel self-tapping screw ⦁ Cavity anchors. 4M fixings are recommended. Accessories Not Included ⦁ Fastening screws. 6g screws should be used when fixing the reader directly to the wall. Cheese head screws are recommended. Countersunk screws are not advised.
Mounting with Vandal Resistant Cover Accessory The optional vandal resistant cover (VRC) accessory provides durability and protection against vandalism and malicious damage. The flush design also serves as an anti-ligature measure for an additional level of safety. P UL ULC The vandal resistant cover accessory has not been evaluated for UL/ULC applications.
Vandal-proof Silicone Seal Before installing the vandal resistant cover, silicone is applied along the top and side edges of the card reader to ensure a sealed vandal-proof installation and maintain the impact protection rating. The silicone is applied after the reader has been mounted, forming an exact fit at the mounting location. ⦁ ⦁ ⦁ Ensure that the bottom of the reader is not sealed, so that the faceplate can still be removed. Be careful not to leave excess silicone which may impede the VRC mounting.
Mounting with Surface Mount Box Accessory The optional surface mount box (SMB) accessory enables you to mount the card reader projected from the wall, allowing space for cabling from external conduits. The surface mount box is the same height and width as the card reader rear case, with a protected cavity to allow external cabling to be securely connected to the reader. The processes for mounting Standard and Extra readers with the surface mount box are slightly different.
5. Hold the rear case of the card reader against the surface mount box in the correct orientation. Line up the holes on the rear case with the threaded inserts closest to the center of the surface mount box, as shown in the image below. 6. Affix the rear case to the surface mount box using the two M4 x 10mm screws provided. 7. Connect the wiring to the reader electronics through the conduit hole. Refer to later sections of this manual for the wiring connections. 8.
Reader Connection Using the recommended cables, splice the cable together with the pigtail of the reader and seal the splice. Route the cable from the reader to the host module. Connect the cable to the module port according to the required operation, as shown in the connection diagrams that follow.
Shield Connection 1. Connect the reader pigtail shield and cable shield wires together at the reader pigtail splice. 2. Connect the cable shield to a suitable earth point. Do not connect the shield to a ground or AUX connection. The reader pigtail shield wire is not terminated inside the reader. 1 2 3 4 5 6 7 8 9 0 X Important: ⦁ The card reader must be connected to the module port using a shielded cable. ⦁ Do not connect the cable shield to any shield used for isolated communication.
RS-485 Reader Connection The connection of a single RS-485 reader to a reader expander. 1 2 3 4 5 6 7 8 9 0 X C BZ L2 L1 D1/ D0/ NB NA V- V+ Reader Connections Color Wire Connection Red V+ 12VDC positive Black V- 12VDC negative Yellow D0/NA RS-485 A Violet D1/NB RS-485 B Shield Shield (drain) wire.
RS-485 Reader Connection (Entry/Exit) The connection of two RS-485 readers to a reader expander providing an entry/exit configuration. 1 2 3 4 5 6 7 8 9 0 X C BZ L2 L1 D1/ D0/ NB NA V- V+ A 330 ohm EOL (End of Line) resistor may be required, inserted between the yellow and violet wires after the join.
Secondary Reader Connections Color Wire Connection Red Join to primary reader red wire ( 12VDC positive) Black Join to primary reader black wire ( 12VDC negative) Yellow Join to primary reader yellow wire (RS-485 A) Violet Join to primary reader violet wire (RS-485 B) Shield Join the shield (drain) wires together.
OSDP Reader Connection Connecting TSL readers in OSDP mode is the same as the connection for standard RS-485 configuration. 1 2 3 4 5 6 7 8 9 0 X C BZ L2 L1 D1/ D0/ NB NA V- V+ Reader Connections Color Wire Connection Red V+ 12VDC positive Black V- 12VDC negative Yellow D0/NA RS-485 A Violet D1/NB RS-485 B Shield Shield (drain) wire. Frame grounded at one point only Readers must also be programmed to operate in OSDP mode.
OSDP Baud Rate Requirement For a card reader operating in OSDP mode to communicate with an OSDP server, the reader must have the same baud rate setting as the reader port it is connected to. The default reader baud rate is 38400. ICT card readers support the following baud rates: Supported Baud Rates 4800 baud 9600 baud 19200 baud 38400 baud (default) 57600 baud 115200 baud The card reader baud rate can be programmed using a mobile device running the Protege Config App.
Wiegand Reader Connection When connected using the Wiegand interface, TSL readers operate in single LED mode, which allows a single LED line to control the two reader LED colors. TSL readers do not support dual LED operation for Wiegand interfaces.
Wiegand Reader Connection (Entry / Exit) In multiple reader mode, the secondary card reader has all connections wired to the same reader port as the primary reader, except the Data 1 connection which is wired to the Data 1 input on the alternate reader port. The normal primary reader connection operates as the entry reader, and the secondary reader that is multiplexed into the alternate reader port will operate as the exit reader.
Exit Reader Connections Color Wire Connection Red Join to entry reader red wire ( 12VDC positive) Black Join to entry reader black wire ( 12VDC negative) Green Join to entry reader green wire (Wiegand Data 0) White D1/NB Wiegand Data 1 (alternate reader port to entry reader) Brown Join to entry reader brown wire (LED control) Blue Join to entry reader blue wire (beeper control) Shield Join the shield (drain) wires together.
Programming the Card Reader ICT readers can be programmed for a wide range of functionality to suit your site's requirements. Programming options are dependent on hardware compatibility and firmware versions. Card reader programming is configured by applying specific TLV (Type Length Value) settings to the reader to enable, disable and configure reader options. Reader configuration can be programmed using a mobile device running the Protege Config App.
Technical Diagrams TSL Standard Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Standard Reader. All measurements are shown in millimeters. ø 18mm Connector Hole (Min) 47.6 47.6 84.0 117.0 36.4 51.9 ø 4.5mm Screw Hole ø 4.5mm Screw Hole 21.5 21.5 43.
TSL Extra Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Extra Reader. All measurements are shown in millimeters. 44.5 60.0 ø 4.5mm Screw Hole 57.0 39.5 84.0 117.0 ø 18mm Connector Hole (Min) ø 4.5mm Screw Hole 37.5 37.5 75.
TSL Mini Reader The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Mini Reader. All measurements are shown in millimeters. 2 6 .1 ø 1 8 mm Connector H ole (M in) 4 7 .4 3 3 .9 6 0 .0 8 7 .0 3 9 .6 ø 4.5mm Screw Hole ø 4.5mm Screw Hole 2 1 .5 2 1 .5 4 3 .
TSL Standard Reader Vandal Resistant Cover The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Standard Reader Vandal Resistant Cover. All measurements are shown in millimeters. 89.00m m 3.504in 41.50m m 1.634in 41.50m m 1.634in 5.3m m 0.207in Mounting Holes 29.00m m 1.142in 162.00m m 6.378in 29.00m m 1.142in 11.70m m 0.
TSL Extra Reader Vandal Resistant Cover The dimensions shown below outline the essential details needed to help ensure the correct installation of the ICT TSL Extra Reader Vandal Resistant Cover. All measurements are shown in millimeters. 121.00mm 4.764in 29.00mm 1.142in 11.70m m 0.461in 29.00m m 1.142in 41.50m m 1.634in 162.00m m 6.378in 41.50mm 1.634in 5.3m m 0.207in Mounting Holes 60.50m m 2.382in 60.50m m 2.
Technical Specifications The following specifications are important and vital to the correct operation of this product. Failure to adhere to the specifications will result in any warranty or guarantee that was provided becoming null and void. Ordering Information Order Codes See Reader Editions. Power Supply Operating Voltage 12VDC (9.5 to 14VDC) Operating Current 120mA (Peak, Reading) Communications MIFARE: 50mm (1.97") DESFire EV1 ISO: 5mm (0.2") Card Read Range DESFire EV2 ISO: 25mm (0.
Android 4.4 or above, with phones which support ISO7816-4 NFC (Near-field communication) Proprietary Secured DESFire credential electronic credential transmission Credential is AES-256 (NIST certified AES algorithm) technology Credentials can be distinguished by unique site code and card number NFC Wireless Device Protege Mobile 1.0.
3.5m Pigtail Cable TBC TBC * Applies to multi technology models only The size of conductor used for the supply of power to the unit should be adequate to prevent voltage drop at the terminals of no more than 5% of the rated supply voltage. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Integrated Control Technology is under license. Other trademarks and trade names are those of their respective owners.
New Zealand and Australia Intentional Transmitter Product Statement The R-NZ compliance label indicates that the supplier of the device asserts that it complies with all applicable standards.
European Standards CE Statement Conforms where applicable to European Union (EU) Low Voltage Directive (LVD) 2014/35/EU, Electromagnetic Compatibility (EMC) Directive 2014/30/EU, Radio Equipment Directive (RED)2014/53/EU and RoHS Recast (RoHS2) Directive: 2011/65/EU + Amendment Directive (EU) 2015/863. This equipment complies with the rules, of the Official Journal of the European Union, for governing the Self Declaration of the CE Marking for the European Union as specified in the above directive(s).
UK Conformity Assessment Mark General Product Statement The UKCA Compliance Label indicates that the supplier of the device asserts that it complies with all applicable standards.
UL and ULC Installation Requirements Only UL / ULC listed compatible products are intended to be connected to a UL / ULC listed control system. CAN/ULC-S319 ⦁ This card reader is CAN/ULC-S319 Listed for Class I applications only. ⦁ Fail secure locking mechanism shall only be installed where allowed by the local authority having jurisdiction (AHJ) and shall not impair the operation of panic hardware and emergency egress.
FCC Compliance Statements FCC PART 15, WARNINGS: INFORMATION TO USER This equipment complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Industry Canada Statement This class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Disclaimer and Warranty Disclaimer: Whilst every effort has been made to ensure accuracy in the representation of this product, neither Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice. For warranty information, see our Standard Product Warranty.
Designers & manufacturers of integrated electronic access control, security and automation products. Designed & manufactured by Integrated Control Technology Ltd. Copyright © Integrated Control Technology Limited 2003-2022. All rights reserved.
