User's Manual

Rev.00 20131023
The component of product
For measurement of body and surface temperature.
Product scope
Thank you for purchasing the non-contact
electronic thermometer, Please read through this
manual before using the product.
Cautions
1. Do not drop or shock the unit.
2. Do not immerse the unit into water.
3. Keep the unit out of reach of children.
4. Avoid touching the lens with bare hand.
5. Do not use in areas with strong electromagnetic
interference.
6. Consult your physician if the reading is out of normal
body temperature range.
7. Remove the batteries from the thermometer if the
unit will not be used for an extended period of time.
This will prevent battery leakage causing damage
to the thermometer.
8. If the unit is not working properly, please contact
customer service.
9. Do not disassemble the unit, Open the battery
cover only when replacing batteries.
Setting
F-02: Offset value for surface mode(-2.0~+2.0).
F-03: Temperature Unit (
O
C/
O
F).
F-04: Delete records(Yes,No)
4. Save setting value.
Pressing the "SET" key for 3 seconds to save
the value and exit setting mode. If F-04 value is
"YES", The thermometer will be delete all records.
- 1- - 2- - 3- -4-
O
C /
O
F unit conversion formula
O
F=1.8x
O
C+32
Cautions ..................................................2
Special Features .....................................2
Measurement Principle ...........................2
Product scope .........................................3
The component of product ......................3
Setting .....................................................3
O
C /
O
F unit conversion formula ...............4
Method of measurement .........................4
Connect iOS device via Bluetooth ..........5
Memory Function ....................................6
Replacing the Batteries ...........................6
Cleaning and Care ..................................6
Display Message .................................... 7
Product Specifications .............................8
Contents
1. Pressing "Power" and display and showen the last
records.
2. Pressing the "MEM" key to switch record shows
upper
* LCD display test records and record number.
3. Switch mode
* Pressing the "MODE" key to switch MODE.
Memory Function
Method of measurement
Cleaning and Care
1. Use a soft, dry cloth to clean the exterior of the
thermometer.
Product specification
- 5- - 6- - 7- - 8-
TET-381
Infrared Thermometer
±0.3
O
C
Project
5~10cm
16~35
O
C
±0.4
O
C10~40
O
C
LCD display
＜2.2V±0.3
0.1
O
C
50 Group memory
O
C ,
O
F
-20
O
C~+50
O
C
10
O
C~40
O
C
1 minute after not being used
159×87.5×45.5 mm
About 98g (Not including batteries)
2 x AA
Measuring type
Measuring mode
Measuring distance
Accuracy
Memory
Automatic shutdown
Storage temperature
Work surrounding
Unit
Display resolution
Low voltage tip
Indicator Functions
Battery
Size
Weight
Content
Infrared measuring
Surface/body temperature
32~42.2
O
C
20~32
O
C
42.2~60
O
C
Measuring
Surrounding
Accuracy
Connect iOS device via Bluetooth
Replacing the Batteries
Products use battery by 2, when a battery symbol
appears and flash in the screen, and replace the
battery as soon as possible.
• Note:
1. Open the battery cover to
replace batteries, and
place the battery is the
location of the negative
electrode correctly.
2. If not use, please take out
the battery so as to
protect instrument.
Pull and open the
battery cover from
then on
and environmental temperature, and once the user
has to pass the instrument near certain parts of the
body (forehead), and press the measure button can
immediately active infrared radiation sensor.
• Note:
The correct method of use is the key to test the
accuracy. Please follow these instructions, so as to
avoid the infrared measurement on the surrounding.
1. Testing temperature, as the showing in the figure,
instrument and the distance from the forehead
suggested in 5cm to 10cm.
2. Keep the body's temperature as the same as the
surrounding.
3. It should be avoided cold and any disease of cool
down the temperature.
4. Keep the Instrument's temperature as the same
as the surrounding.
5. Forbidden to use this instrument in the strong
sunshine place.
6. Measure suggestion: 3 times or so, every time
when to display up to a set of data shall prevail.
5~10cm
Power/Measure
Battery cover
Cranium
Memory
LCD
Set
Mode
Back Front
Display
message
Situation
Solution
Allow the thermometer
remain in room
temperature (10-40
O
C)
for 30 minutes.
Ambient temperature
is out of operating
range (10-40
O
C)
Sensor error Please contact with the
customer service.
Please contact with the
customer service.
Temperature measured
is higher than normal
human temperature
range
(Body above 42.2
O
C;
Surface above 60
O
C)
Check the measured
object and take a
new measure.
Temperature measured
is lower than normal
human temperature
range (Body below 32
O
C;
Body below 20
O
C)
Check the measured
object and take a
new measure.
Low battery Replace batteries.
Memory error
Special Features
1. Measurement range: Body: 32~42.2
O
C / 90~108
O
F
Surface: 20~60
O
C / 68~140
O
F
2. Free to set alarm temperature.
3. Non-contact measurement, avoid cross infection.
4. Memory for 50 readings.
5. Auto power off without use it.
6. Unit of Measure:
O
C/
O
F.
7. Backlight.
Measurement Principle
Measuring the temperature of the body and the
surface on forehead with infrared. Products the same
built-in infrared sensor and related hardware,
software, can sense the analyte, analysis and records
1. Pressing the “SET” Key for 3 seconds, The
thermometer will be turn on and enter the setting
mode, the LCD display F-00 and alarm temperature
value.
2. Modify the setting value
Pressing the "MODE" or "MEM" key to change the
value.
3. Switch to other setting item:
Press the "SET" key to switch to other item.
F-01: Offset value for body mode(-2.0~+2.0).
1. Pressing "Power" and display.
2. Press "MODE" key to select temperature
measurement mode (body or surface) :
(1) Thermometer is straight to the forehead, and
distance is 5~10cm.
1. Installation
Prior to first use, Download and install application to
your iOS device. (Bluetooth 4.0 capabilities,
e.g. iPhone 4S, iPhone 5, NewiPad and iPadMini).
2. Open application, and then press the Blood
Pressure icon on Measure screen.
3. Press the “Enter” button.
4. Press the “Thermometer” button.
5. When the measurement is complete, the
temperature will display on Thermometer monitor &
save on iOS application screen.
6. This thermometer stores the last temperature
readings.
(2) Pressing and holding the "Measure" key and
move thermometer scaning forehead.
(3) Release the "Measure" key to finish
measurement and display the result on LCD.
(4) Turn off: The thermometer will trun off
automatically without use for 1 minute.
2. Keep the thermometer away from direct sunlight,
dust and contamination environment.
3. Store the thermometer in normal room
temperature, or within 10-40
o
C.
4. Don't touch with the finger.
5. Can use less than 75% of the rubbing alcohol to
clean the lens.
Display Message
③ ④ ⑤ ⑥
Body Surf ace
This appliance conforms to the following
standards:
EN60601-1: Medical electrical equipment Part 1: General
requirements for safety
EN12470-5: Clinical thermometers Part 5: Performance of
infrared ear thermometers (with maximum
device)
93/42/EEC : Medical Device Directive
ASTM E 1965-98: Standard Specification for Infrared
Thermometers for Intermittent
Determination of Patient Temperature
IP is short for Ingress Protection which means that
Protection’s level.
Manufacturer
Rerfer to the instructions
Equipment of BF
Recycling and Processing
The european Union flag