Instructions / Assembly

Installation & Assembly Instructions
Please contact our Customer Service Division with any questions at:
30700 D Carter Street ∙ Solon, OH 44139 ∙ (P) 440.248.5480 ∙ [e-mail]
For a full line of products visit www.tritonproducts.com 1
Read all instructions completely before installing. For questions about your installation, please call Customer Service at 440-248-5480
If this product was shipped directly to you report damaged shipping cartons within 24 hours of delivery to Shipping/Delivery Company
Missing and Damaged parts must be reported within 5 business days from delivery date.
Tools needed for this installation (Not Supplied with Kit)
Level Pencil or marker Phillips Head Screw Driver Electric Drill ½” Standard Drill Bit for hollow wall installation
Safety Glasses 5/16” Masonry Bit for Concrete block Installation 1/16” Standard Drill bit for Stud wall Installation Tape measure
Parts Listing
P/N# Qty= Description ___ Hardware______________________
1700 3 Top Track Sections 2-1/2” Toggle Bolts
1701 3 Top Hang Rail with hanging Slots 3-1/2” Toggle Bolts
1738 3 Long Hanger Hooks White Plastic Wall Anchors
1755 1 31” Metal Shelf with brackets 2-1/4” Wood Screws
1720 2 31” Wire Shelf with brackets Toggle Bolt Expanders
1705 1 LocBoard steel pegboard 1 Hex Head Wrench for Hang Rails
1721 1 Clothes Hanger Bar
We have included all mounting hardware for hollow and concrete block wall installations. It is not necessary to mount system to wood studs. Each
system will require 96 lineal Inches of wall space for mounting and a minimum ceiling height of 7-1/2 feet high for proper clearance.
Drill Diameter Listing: Drill diameter sizing for: Hollow wall Installations; Use 1/2” Standard Drill Bit
Drill diameter sizing for: Concrete wall Installations; Use 5/16” Masonry Drill Bit
Drill diameter sizing For: Wood Stud wall Installations; Use 1/16” Standard Drill Bit for pilot holes
Preparation for Top Track Installation: (Image A-1)
1. When installing in corners, leave 1” space between side wall and your top track.
2. Determine the maximum height of storage you would like available above your flat surface. (See Fig. A-1). For an 8 foot ceiling; 78” off the
floor leaves 18” of storage above and 81” leaves 15” storage above.
3. Using a tape measure, mark your desired height off the floor with a pencil mark.
4. (Refer to Fig. A-1 & A-2) Using a level, align top of top track with your pencil mark in step 3. With top track level, mark the center of each
holes location on your wall. (Note: Before starting to drill holes; always make sure all screw hole locations do not fall in line with electrical
wires, duct work or plumbing inside of your wall. If a potential problem exists, reposition and re-mark screw hole locations.)
5. (Fig. A-2) Drill hole locations marked using the correct drill diameter sizing and type listed above. Should you come in contact with wood
studs, stop and mark the hole with X and after drilling all other holes come back and drill these holes using a 1/16” bit for pilot hole for
wood screws.
Attachment of Top Track to Wall Surfaces: (Fig. A-3)
6. For hollow walls: (Fig. A-3) Use 2-1/2” long toggle bolts with expanders. Insert all toggle bolts through top track and attach all toggle bolt
expanders. Omit toggle bolts that fall in line with X or wood studs. Insert toggle bolts with expanders into holes in wall before starting step
9.
7. For concrete walls: use white plastic wall anchors and 2-1/4” long wood screws. Install plastic wall anchors in hole locations before starting
step 9.
8. For wood studs: use 2-1/4” long wood screws. Always install wood screws last and there will be no need to use plastic wall anchors.
9. Using a level and holding top track in place tighten one of the end toggle bolts or wood screws until snug. (Allow for track movement.)
10. (Fig. A-3) Making sure top track is still level, tighten toggle bolt or install wood screw on the opposite end until fully secure and then go
back and fully tighten the first toggle bolt.
11. Install and fully tighten all remaining toggle bolts or wood screws.
Hanging Hang Rails: (Fig. B-1, B-2 and B-3). Note: When installing hang rails, work from left to right or right to left and always installing one
hang rail at a time.
12. (Fig. B-1 and B-2) Slide each hang rail assembly onto front lip of the top track. Position each hang rail at opposite ends of the track 1/8”
(.125”) in from each end.
13. Starting from one end, make sure the top outside edge of the hang rail is no greater than 1/8” away from the outside vertical straight edge
of the top track. Using a level, make sure hang rail is flat against wall surface and straight; while holding in place mark the centers of the 3
bolt holes locations onto the wall.
1751 – Storability® 96 In. W x 32 In. H Laundry Storage System