Use and Care Manual

Installation & Assembly Instructions
Please contact Customer Service with any questions at:
30700 D Carter Street ∙ Solon, OH 44139 ∙ (P) 440.248.5480 ∙ [e-mail]
For a full line of products visit www.tritonproducts.com 1
Read all instructions completely before installing. Should you have any questions about your installation, please
call Customer Service at 440-248-5480.
• Inventory and inspect all components before starting assembly.
• Report any missing parts and/or damaged goods within 5 days from receipt.
Should you have questions or require installation help, please contact Triton Products directly at 440-248-5480.
Tools needed for this installation (Not Supplied with Kit):
Level, Pencil, Phillips Head Screwdriver, Drill, ½” Standard Drill Bit, Safety Glasses, 1/4” Masonry Bit for Concrete
Wall Installation, 1/16” Standard Drill bit, Tape measure
Parts Listing
P/N# Qty= Description Qty Hardware______________________
1700 2 Top Track Sections 10 2-1/2” Toggle Bolts
1701 3 Hang Rail 6 3-1/2” Toggle Bolts
1720 3 31” Wire Shelf 16 White Plastic Wall Anchors
1721 3 Clothes Hanging Rod 16 2-1/4” Wood Screws
1765 2 Shoe Shelves 16 Toggle Bolt Expanders
1 Hex Head Wrench for Hang Rails
We have included all mounting hardware for hollow and concrete wall installations. It is not necessary to mount
system to wood studs. Each system will require 63.5 linear inches of wall space for mounting and a minimum ceiling
height of 7 feet high for proper shelf clearance.
Drill Diameter Listing:
Drill diameter sizing for: Hollow wall Installations; Use 1/2” Standard Drill Bit
Drill diameter sizing for: Concrete wall Installations; Use 1/4” Masonry Drill Bit
Drill diameter sizing for: Wood Stud wall Installations; Use 1/16” Standard Drill Bit for pilot holes
Preparation for Top Track Installation: (Image A-1)
1. If installing in a corner, leave 1” space between side wall and Top Track.
2. Determine the maximum height of storage you would like available above your system. (See Fig. A-1). For
an 8 foot ceiling; 78” off the floor leaves 18” of storage above and 81” leaves 15” storage above.
3. Using a tape measure, mark the desired height from the floor for the Top Wire Shelf.
4. (Refer to Fig. A-1 & A-2) Using a level, align top of top track with your pencil mark in step 3. With Top Track
level, mark the center of each hole location on your wall. (Note: Before starting to drill holes; always make
sure screw hole locations do not fall in line with electrical wires, duct work or plumbing inside your wall. If a
potential problem exists, reposition and re-mark screw hole locations.)
5. (Fig. A-2) Drill hole locations marked using the correct drill bit listed above. Should you come in contact
with wood studs, stop and mark the hole with an “X”. After drilling all other holes come back and drill
holes marked with an “X” using the 1/16” bit for pilot holes for the wood screws.
Attachment of Top Track to wall surface: (Fig. A-3)
6. For hollow walls: (Fig. A-3) Use 2-1/2” long toggle bolts with expanders. Make sure to insert all toggle bolts
through Top Track and attach all toggle bolt expanders, insert toggle bolts with expanders into holes in wall
before starting step 9.
7. For concrete walls: use white plastic wall anchors and 2-1/4” long wood screws. Install plastic wall anchors
into each pre-drilled hole location before starting step 9.
8. For wood studs: use 2-1/4” long wood screws. Always install wood screws last and there will be no need to
use plastic wall anchors.
1730 – Storability ® Modular Closet, Garage, and Laundry Organizer Kit