Instruction 1. Garage Door Lock A set garage door lock is including the lock box, wall console, outside panel and remote control, which is used for smart control of garage door. 1.1. Lock Box Function: Lock/ Unlock/ Adaptive remote control Delete all passwords and matched remote control: long press ”SETUP”&”LEARN” at the same time till the working indicator light flickering 2 times and beeps for one time.
1.2. Wall Console Function: 1. Lock/ Unlock 2. Close the auto lock function 3. Enable/disable other lock mode. Instructions 1. Press the button to open the lock. 2. Press “auto close” to stop this function. 3. Switch the button (bottom right) to the close status that will disable all other locking methods except the button on the wall console. 4. methods.
1.3. Outside panel User can control lock/unlock by setting password on the outside panel while all locking methods are enabled.
Outside panel configuration (Configuration has completed before delivery.) 1. Short press “SETUP” button on the lock box, the working indicator light will turn to green and keep flickering slowly. 2. Press the “RESET” button on the outside panel with needle, till the keypad flickering slowly. 3. After con-fig successfully, keypad will light for 2 seconds. At the same time, the working indicator light of lock box will flickering twice and beeps. 4. If fail to con-fig, keypad light will turn off.
1. 1.4. Enter your 6-digit password and press “ENTER” to unlock. Remote control User can control lock/unlock by using remote control while all locking methods are enabled. Remote control configuration (Configuration has completed before delivery.) 1. Short press “SETUP” button on the lock box, the working indicator light will turn to green and keep flickering slowly. 2. Press the “RESET” button on the remote control with needle, till the LED light keep flickering slowly.
3. After con-fig successfully, LED indicator light of remote control will turn on for 2 seconds. At the same time, the working indicator light of lock box will flickering twice and beeps. 4. If fail to con-fig, the LED indicator light will turn off. After con-fig successfully, user can press the remote control button to unlock. 2.
Search “Bee space” in App Store.
3. APP instruction 3.1. Register After downloaded APP, user can register a new account on below login page.
Enter your email address and click to get the verification code, then check your email and enter the code to click next.
Setting your name, password and agree the service agreement, then click sign up so as to complete the registration.
3.2. Adding devices on APP 3.2.1. Click “+” to add devices.
3.2.2. Select “add manually”. 3.2.3. Select “Garage Lock Kit”.
3.2.4. WiFi Select Wi-Fi network that your mobile phone has been connected.
3.2.5. Press “SETUP” button on the lock box for 5 seconds till the working indicator light turn to blue and flickering slowly, then click “next”.
3.2.6. Connect the hotspot from lock box on the Wi-Fi setting page.
3.2.7. After connected WiFi, then back to APP and click “to connect”.
3.2.8. Lock Box connect to Network.
Click“add to home”
3.2.9. Confirm the gateway and add it to home page. 1. When the working indicator light turns to green and flickering. 2. Press setting button, the working indicator light stop flickering and keeps green. 3. Click next.
Click next.
3.3. Using APP to control the lock. 3.3.1. Operation page User can lock/ unlock the garage door lock, setting auto close and check the operation record and alarm record.
3.3.2. Settings page User can check the garage door lock information, as well as check/ add other devices.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.