User's Manual

ManualsBrandsTrisquare Communications ManualsElectronicsRemote Transceiver

Operating Instructions ICOP 2020WMIC

Items included in this package with part numbers

No. Quantity Model No. Description ICOP Part No.

1 1 2020ICT In-Car Transceiver 600-00111-00

2 1 2020RHT Remote Transceiver 600-00110-00

3 1 2020BC Belt Clip 600-00116-00

4 1 2020ICC In-Car Charger 600-00115-00

5 1 N/A Cable - In-Car Charger 600-00119-00

6 1 2020CPC Cigar Plug Charger 600-00112-00

7 1 2020HOC Home Office Charger 600-00114-00

8 1 N/A Instruction Manual 700-00100-00

System description:

The ICOP 2020WMIC wireless microphone system operates as part of ICOP’s in-car DVR

(digital video recorder) system.

The ICOP 2020 Wireless Microphone System consists of 2 transceivers. The first

transceiver, called the In-Car Transceiver (2020ICT), is mounted inside the vehicle. The

In-Car Transceiver must be connected to the JBOX (junction box) to interface audio and

control signals to the DVR. The In-Car Transceiver consists of two receivers and one

transmitter, a fixed antenna, an RJ-45 connector, and a push button for synchronization

with the Remote Transceivers.

The second transceiver, called the Remote Transceiver (2020RHT), is carried by the

patrolman either on his belt or lapel. The Remote Transceiver is a self-contained unit,

which includes an internal microphone, external microphone/charge jack, battery charge

terminals, internal rechargeable battery, internal antenna, and 3 buttons for Standby/Off,

Help and Transmit Record On/Off.

Summary of content (11 pages)

PAGE 1
Operating Instructions ICOP 2020WMIC Items included in this package with part numbers No. Quantity Model No. Description ICOP Part No.
PAGE 2
The system operates in the 900 MHz ISM (Instrument Scientific Medical) band and is license free. The system range is 1000 feet. The ICOP 2020 Wireless Microphone System uses Frequency Hopping Spread Spectrum (FHSS) Narrow Band FM, which provides excellent privacy, security and avoidance of interference. Three chargers are included with the 2020WMIC system. These are the In-Car Charger (2020ICC), the Cigar Plug Charger (2020CPC) and the Home Office Charger (2020HOC).
PAGE 3
its red SYNC Status LED and attempt a link confirmation with the first Remote Transceiver unit on its currently assigned channels. The In-Car Transceiver will then attempt a link confirmation with a second Remote Transceiver. After the attempts are completed, the InCar Transceiver’s red SYNC Status LED will blink one or two times every five seconds for three minutes to indicate the number of Remote Transceiver units found. If no units are found, the SYNC Status LED will remain off.
PAGE 4
2020RHT Red LED Green/Yellow LED Power Button Microphone/Charge Jack RECORD Button Microphone HELP Button Charge Terminals Operating instructions: The Remote Transceiver has an internal 550 mA hour rechargeable battery pack. Prior to the first use the battery should be charged for 12 to 15 hours.
PAGE 5
minutes to indicate that two Remote Transceivers are synchronized to the In-Car Transceiver. If only one Remote Transceiver unit is found and confirmed, the In-Car Transceiver will enter programming mode on the special low-power synchronization channel and attempt to program the current security and channel information into the next Remote Transceiver unit available in charge mode that it can find.
PAGE 6
until the green LED goes off. The green LED will turn ON for the duration of the Power Button, press up to 1 second. If held for 1 second when the RHT is in the OFF mode, the RHT will enter the Standby mode. If the RHT unit is currently synchronized with an In-Car Transceiver, the Remote Transceiver will rapidly flash the green LED and attempt a confirmation with the In-Car Transceiver.
PAGE 7
Belt Clip Insert the hook-and-loop strap through the belt clip as shown. Wrap the hook-and-loop strap around your belt and squeeze the hook portion against the loop section so that the belt clip is securely fastened to your belt. Snap the Remote Transceiver onto the belt clip by inserting the swivel connector on the belt clip into the mounting hole on the back of the Remote Transceiver. To Remove the Remote Transceiver from the belt clip, push the release latch on the belt clip.
PAGE 8
2020ICC Remote Transceiver In-Car Charger Power Jack Operating instructions: Insert the Remote Transceiver into the In-Car Charger. The red LED on the Remote Transceiver will light and begin blinking in a few seconds.
PAGE 9
2020CPC Plug into Vehicle Cigar Lighter Outlet or Power Port Plug into Remote Transceiver’s Charge Jack Operating instructions: Plug the Cigar Plug Charger into the vehicle’s cigar lighter outlet or power port. Insert the plug on the Cigar Plug Charger into the microphone/charge jack on the top of the Remote Transceiver. The red LED on the Remote Transceiver will light and begin blinking in a few seconds.
PAGE 10
Battery 75% Battery 100% 3 Red Blinks 4 Red Blinks ICOP Digital, Inc will, without charge, repair or replace, at its option, defective components of the 2020WMIC system upon delivery to the ICOP Factory Service department, accompanied by proof of the date of purchase, such as a duplicated copy of sales receipt.
PAGE 11
Multiple Office Charger 2020MOC Items included in package with part numbers No. Quantity Model No. Description ICOP Part No. 1 2 3 1 1 1 2020MOC N/A N/A Multiple Office Charger AC Adapter for MOC Instruction Manual 600-00113-00 600-00117-00 700-00101-00 Remote Transceivers Jack for AC Adapter Multiple Office Charger Operating instructions: Plug the Multiple Office Charger’s AC adapter into a standard 120V AC outlet. Only use the AC adapter supplied with the Multiple Office Charger.