Owner’s Manual VGA Over Cat5 Extenders and Extender/Splitters Extender Kit Models: B130-101-2, B130-101A-2, B130-101-WP-1, B130-101A-WP-2, B130-101S-2, B130-111, B130-111A and B130-101-U Transmitter Unit Models: B132-002-2, B132-002A-2, B132-004-2 and B132-004A-2 Receiver Unit and Remote Repeater Models: B132-100-1, B132-100A, B132-100-WP-1, B132-100A-WP-1, B132-110 and B132-110A 1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support 14-11-071-9333F9.indd 1 Copyright © 2014 Tripp Lite.
Table of Contents Package Contents 3 Optional Accessories 10 Product Features All B130-101-2 B130-101A-2 B130-101-WP-1 B130-101A-WP-2 B130-101S-2 B130-111 B130-111A B130-101-U B132-002-2 B132-002A-2 B132-004-2 B132-004A-2 B132-100-1 B132-100A B132-100-WP-1 B132-100A-WP-1 B132-110 B132-110A 4 4 4 4 4 5 5 5 6 6 7 7 7 8 8 8 8 8 9 9 Mounting Hardware Instructions 11 Installation EDID Copy Extender Kit Installation Non-Kit Standard Installation Non-Kit Daisy Chain Installation Extender/Repeater Kit Ins
B130-101-2 B130-101A-2 B130-101-WP-1 B130-101A-WP-2 B130-101S-2 B130-111 B130-111A B130-101-U B132-002-2 B132-002A-2 B132-004-2 B132-004A-2 B132-100-1 B132-100A B132-100-WP-1 B132-100A-WP-1 B132-110 B132-110A Package Contents Local Unit (L), Remote Unit (R) or Both (B) 1 or 2 External Power Supplies (Input: 100240 V, 50/60 Hz, 0.5 A Output: 5 V, 2 A) Mounting Hardware Wallplate Screws Screwdriver 3.5 mm Male to DB9 Male Adapter Cable 3.5 mm Male to DB9 Female Adapter Cable 1 ft. VGA Splitter Cable 1 ft.
Product Features All • • • • Support a maximum resolution of 1920 x 1440 @ 60 Hz. All operating systems supported. Plug and play; no software or drivers required. HDCP compliant. B130-101-2 • Extends a VGA video signal (1024 x 768 @ 60 Hz) up to 1,000 ft. from the source. • Features an additional VGA port, allowing for the connection of a local monitor. • Includes mounting hardware that allows units to be wall-mounted, rack mounted or pole mounted.
Product Features continued B130-101A-WP-2 • Extends both a VGA video (1024 x 768 @ 60 Hz) and an audio signal up to 1,000 ft. from the source. • Includes a VGA + audio splitter cable, which allows for the connection of a local monitor and speakers. • Includes RJ45 jacks, allowing for easy connection via standard patch cables; no 110 punchdown connections required. • Features built-in equalization and gain controls to adjust the video image. • EDID copy feature ensures optimal display compatibility.
Product Features continued B130-111A • Kit comes with both local transmitter and remote repeater units. • Locate multiple monitors/speakers at different points in a chain of up to 2,000 ft. by connecting an additional remote receiver unit (B132-100A or B132-100A-WP-1), or a remote repeater unit (B132-110A). • Up to 4 remote units (3 remote repeaters and 1 receiver) can be connected together, providing audio/video to up to 4 remote displays/ speakers in a full chain.
Product Features continued B132-002-2 • Works with the B132-100-1 and B132-100-WP-1 remote units to extend a VGA video signal (1024 x 768 @ 60 Hz) up to 1,000 ft. from the source. • Able to transmit a single VGA video signal to 2 monitors. • Includes mounting hardware that allows unit to be wall-mounted, rack mounted or pole mounted. • EDID copy feature ensures optimal display compatibility.
Product Features continued B132-004A-2 • Works with the B132-100A and B132-100A-WP-1 remote units to extend both a VGA video (1024 x 768 @ 60 Hz) and an audio signal up to 1,000 ft. from the source. • Features additional VGA and 3.5 mm ports, allowing for the connection of a local monitor and speakers. • Transmits a single VGA video and audio signal to up to 5 sets (4 remote, 1 local) of monitors and speakers.
Product Features continued B132-110 • Both extends and expands your Tripp Lite VGA over Cat5 installation, allowing you to locate multiple monitors at different points in a chain of up to 2,000 ft. • Up to 4 remote units (3 remote repeaters and 1 receiver) can be connected together, providing video to up to 4 remote displays in a full chain. • Extends a 1024 x 768 (60 Hz) signal up to 1,000 ft. between the local transmitter and the first remote repeater unit in the installation.
Optional Accessories • • • • • • • • • • B132-004-RB 1U Rackmount Bracket N022-01K-GY Gray Cat5e Bulk 24 AWG Solid Cable – 1,000 ft. N030-010 10-pack of RJ45 Plugs for Solid-wire Cat5e Cable N202-Series Cat6 Snagless 24 AWG Solid Patch Cables N222-01K-GY Gray Cat6 Bulk 24 AWG Solid Cable – 1,000 ft. P312-Series Audio Cables P502-Series VGA Monitor Cables with RGB Coax P504-Series VGA Monitor + Audio Cables with RGB Coax P520-006 RS-232 Serial Extension Cable – 6 ft.
Mounting Hardware Instructions All of the non-wallplate VGA extender products come with mounting hardware that allows them to be mounted in a variety of ways. The following images show the different ways the included mounting brackets can be attached for different mounting methods. Note: The images below show a B140-101X DVI Extender, but mounting is the same for the VGA Extenders. The B132-004-2 and B132-004A-2 can also be mounted to a Tripp Lite B132-004-RB 1U rackmount bracket.
Installation EDID Copy Compatibility issues can occur when EDID information is not properly communicated between the source and the display. Select models include an EDID copy feature which stores a monitor’s EDID information in the transmitter and sends it to the source, ensuring optimal compatibility. The transmitter can only store EDID information copied from a single monitor.
Installation continued 3 Connect the external power supply to the transmitter unit and plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or Uninterruptible Power Supply (UPS). 4 Wait 10 seconds for the EDID information to be copied, and then disconnect the monitor from the transmitter unit’s input port and proceed per the installation instructions in this manual. 5 You can verify that the EDID information was copied via the Display Settings screen in your computer.
Installation continued Extender Kit Installation (B130-101-2, B130-101A-2, B130-101-WP-1, B130-101A-WP-2, B130-101S-2, B130-101-U) Receiver Unit Transmitter Unit Note: 1. For models that support EDID copy, perform the EDID copy procedure described in this manual prior to installation. 2. The diagram above shows a B130-101A-2 VGA + Audio Extender Kit installation. Installation will be the same for other extender kit models, with the exception of units featuring VGA + RS-232 serial or VGA only.
Installation continued 1 Make sure that the VGA, audio* and RS-232 serial* source is powered off. 2 (B130-101-2, B130-101A-2 and B130-101S-2 only) – Connect 3 4 5 6 the VGA and audio* source to the INPUT port(s) on the transmitter unit using a VGA and audio* cable. (B130-101S-2 only) – Connect the included 3.5 mm Male to DB9 Female adapter cable to the 3.5 mm INPUT port on the transmitter unit, and then connect the computer to the adapter using a DB9 cable.
Installation continued 10 Connect a monitor and speakers* to the OUTPUT ports on the receiver unit using a VGA and audio* cable. 11 (B130-101S-2 only) – Connect the included 3.5 mm Male to DB9 12 13 14 15 Male adapter cable to the 3.5 mm OUTPUT port on the receiver unit, and then connect the serial device to the adapter using a DB9 cable.
Installation continued Non-Kit Standard Installation B132-100A Source PC B132-004A-2 B132-100A-WP-1 Note: 1. For models that support EDID copy, perform the EDID copy procedure described in this manual prior to installation. 2. The diagram above shows a B132-004A-2 VGA + Audio Extender/Splitter Kit installation. Installation will be the same for non-audio models, except that an audio source and speakers will not be connected. 3.
Installation continued 1 Make sure that the VGA and audio* source is powered off. 2 Connect the VGA and audio* source to the INPUT port(s) on the transmitter unit using a VGA and audio* cable. 3 (Optional – B132-004-2 and B132-004A-2 only) – Connect a local monitor and speakers* to the LOCAL port(s) on the transmitter unit.
Installation continued Non-Kit Daisy Chain Installation (B132-004-2 and B132-004A-2 only) Source PC Local PC and Speakers (Optional) B132-100A B132-100A-WP-1 B132-004A-2 Note: 1. For models that support EDID copy, perform the EDID copy procedure described in this manual prior to installation. 2. The diagram above shows a B132-004A-2 VGA + Audio Extender/Splitter Kit daisy chain installation.
Installation continued 1 Make sure that the VGA and audio* source is powered off. 2 Connect the VGA and audio* source to the INPUT port(s) on the transmitter unit using a VGA and audio* cable. 3 Using the included daisy chain cable, connect the LOCAL port(s) on the transmitter unit to the INPUT ports on a second-level transmitter unit. Note: A standard VGA cable can be used to increase the distance between units with no more than 6 ft. between.
Installation continued Extender/Repeater Kit Installation (B130-101-2, B130-101A-2, B130-101-WP-1, B130-101A-WP-2, B130-111 and B130-111A) Note: 1. For models that support EDID copy, perform the EDID copy procedure described in this manual prior to installation. 2. An extender/repeater kit installation can start with a B130-101-2, B130-101A-2, B130-101-WP-1, B130-101A-WP-2, B130-111 or B130-111A. The only difference between these kits is the type of remote unit that comes with them.
Installation continued 5. To achieve maximum distance and performance, 24 AWG solid-wire Cat5e/6 cable must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. All Tripp Lite N202-Series cables are made with 24 AWG solid-wire cabling. Tripp Lite N022-01K-GY (Cat5e) and N222-01K-GY (Cat6) are 24 AWG solid-wire bulk cables. For optimal image quality between 500 and 1,000 ft.
Installation continued If you are not connecting additional remote repeater units, proceed to step 11 to complete the chain with a receiver unit. 8 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first remote repeater unit to the RJ45 INPUT port on a second remote repeater unit. 9 On the remote repeater unit that you just added, connect a monitor and speakers* to the OUTPUT port(s) using a VGA video and audio* cable.
Installation continued Non-Kit Remote Repeater Installation Note: 1. For models that support EDID copy, perform the EDID copy procedure described in this manual prior to installation. 2. The diagram above shows a B132-004-2 installation with the maximum number of remote units connected. A B132-004A-2 installation will be the same, except there will be audio connections.
Installation continued 5. To achieve maximum distance and performance, 24 AWG solid-wire Cat5e/6 cable must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. All Tripp Lite N202-Series cables are made with 24 AWG solid-wire cabling. Tripp Lite N022-01K-GY (Cat5e) and N222-01K-GY (Cat6) are 24 AWG solid-wire bulk cables. For optimal image quality between 500 and 1,000 ft.
Installation continued 8 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first remote repeater unit to the RJ45 INPUT port on a second remote repeater unit. 9 On the remote repeater unit that you just added, connect a monitor and speakers* to the OUTPUT port(s) using a VGA video and audio* cable. 10 Connect the external power supply to the remote repeater unit, and then plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or Uninterruptible Power Supply (UPS).
Installation continued Non-Kit Daisy Chain Remote Repeater Installation (B132-004A-2 and B132-004-2 only) Note: 1. For models that support EDID copy, perform the EDID copy procedure described in this manual prior to installation. 14-11-071-9333F9.
Installation continued 2. The diagram shows a B132-004-2 installation with the maximum number of remote units connected. A B132-004A-2 installation will be the same, except there will be audio connections. B132-002-2 and B132-002A-2 local units cannot be daisy chained. 3. A 1024 x 768 (60 Hz) signal can be extended up to 1,000 ft. between the local transmitter and the first remote repeater unit in the installation. Up to an additional 1,000 ft.
Installation continued 5 Connect the external power supply to the first transmitter unit in the installation, and then plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or Uninterruptible Power Supply (UPS). The Red power LED and the Green RJ45 LED will illuminate to indicate the unit is receiving power. Repeat step 5 for each transmitter unit in the installation. When power has been connected to all of the transmitter units, proceed to step 6.
Installation continued 12 Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the last remote repeater unit to the RJ45 INPUT port on a receiver unit. 13 Connect a monitor and speakers* to the OUTPUT port(s) on the receiver unit using a VGA video and audio* cable. 14 Connect the external power supply to the receiver unit, and then plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or Uninterruptible Power Supply (UPS).
Troubleshooting If you are unable to get an acceptable image after following the installation instructions, try the troubleshooting tips below. 1. Are the external power supplies that came with the product connected and plugged into a working power source? For the product to function properly, it must be connected to and receiving power from the external power supply. 2. Was the power to the VGA source turned off prior to installation? If not, restart your computer. 3.
Troubleshooting continued 7. What resolution are you trying to reach? Tripp Lite’s VGA over Cat5 extenders are tested to support up to 1920 x 1440 @ 60 Hz video resolution (See the Product Features section in this manual for details on max distance and resolution). The shorter the extension distance, the higher the resolution you will be able to obtain.
Troubleshooting continued 11. Do you have any patch panels or other devices in between the transmitter, repeater and receiver units? Tripp Lite’s VGA over Cat5 extender products were designed to be connected directly from the transmitter to the repeater and/or receiver via UTP cable. The more connection points that are between the source and the remote monitor, the more likely it will be that signal degradation will occur, causing poor performance.
Warranty and Product Registration 1-Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center.
Additional Warnings and Notices WARNING Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide. FCC Notice, Class B This device complies with part 15 of the FCC Rules.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support 14-11-071-9333F9.