TY N for a Lite nty AN TIO ay ripp arra R A od T /w AR TR t EE m W IS nline FR .co G o a ite RE ter win ippl r s gi to .t Re ce www n a t ch duc o pr Owner’s Manual HDMI Matrix Switch Models: B119-2X2, B119-4X4 Package Contents 2 Product Features 2 Mounting 3 Standard Installation 4 RS-232 Serial Control 6 Troubleshooting 9 Warranty & Warranty Registration 10 1111 W. 35th Street, Chicago, IL. 60609 • www.tripplite.com/support 13-08-038-9332BC.
Package Contents • B119-2X2 or B119-4X4 Local Transmitter Unit • External Power Supply (Input: 100-240V, 50/60Hz, 0.5A Output: 5V, 2A)* • 3.
Mounting The B119-2X2 and B119-4X4 come with mounting hardware that allows them to be mounted in a variety of ways. The following images show the different ways the included mounting brackets can be attached for different mounting methods. Note: The images below show a B126-1A1 HDMI over Cat5 Receiver Unit, but the mounting hardware installation is the same for the B119-2X2 and B119-4X4. Wallmount 1 Wallmount 2 19” Rackmount Pole Mount 13-08-038-9332BC.
Standard Installation Note: 1. The diagram below shows a B119-2X2 installation, but installation will be the same for the B119-4X4, except for the number of ports. 2. The back panel of the B119-4X4 contains an IR port which has been capped off. This port is intended for future use, and does not currently function. B119-2x2 (Optional) Blu-Ray™ Up to 16 ft. Up to 16 ft. Up to 25 ft. Up to 25 ft. 1 Make sure all devices being connected are turned off. 2 Optional: Connect the 3.
Standard Installation 6 Connect the first HDMI display to the port on the switch marked Output 1. Note: The HDMI cable connecting the switch to a display must be no longer than 25 ft. 7 Repeat step 6 to connect additional displays to the remaining ports. 8 Turn on the power to the connected devices. The video image should now be displayed on the connected monitors. 9 Press the switch next to each set of Output LEDs to switch the source being displayed on the corresponding Output monitor.
RS-232 Serial Control Before using RS-232 Serial Control, you must first go into your Terminal Emulation Software and update the COM port settings. 1 Go to the Setup drop-down menu and select the Serial Port option. 2 Select the COM port that is being used, and update the remaining settings as follows: Baud Rate (57600), Data (8 bit), Parity (none), Stop (1 bit), Flow Control (none). 13-08-038-9332BC.
RS-232 Serial Control 3 Next, you will need to configure your software to allow input control. Go to the Setup drop-down menu and select the Terminal option. 4 Update the following settings; Receive (LF), Local Echo (enable). The remaining settings can stay as they are. 13-08-038-9332BC.
RS-232 Serial Control 5 Once these settings are updated, the Terminal Emulation Software will recognize the switch, allowing you to enter commands to control it with. The following table lists the available commands. Command Action sw[x] [n] Switches the source being displayed on the selected output. [x] is the output (1, 2, 3, or 4) and [n] is the desired source (A, B, C, or D). For example, a command of sw1 2 would display source 2 on output 1. PWD Turns power to the switch on/off.
Troubleshooting If you are unable to get an acceptable image after following the installation instructions, try the troubleshooting tips below. 1 Is the external power supply that came with the product connected and plugged into a working power source? For the product to function properly, it must be connected to and receiving power from the external power supply. 2 Was the power to the connected devices turned off prior to installation? If not, restart them.
Warranty & Warranty Registration 1-Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center.
Warranty & Warranty Registration WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union) Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to: • Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country) • Send the new equipment back for recycling when this ultimately becomes waste WARNIN
1111 W. 35th Street, Chicago, IL. 60609 • www.tripplite.com/support 13-08-038-9332BC.