USER GUIDE Model: 121132 Version 1.00 Revision A April 2021 https://geospatial.trimble.com/ © 2020, Trimble Inc. All rights reserved. Trimble and the Globe & Triangle logo are trademarks of Trimble Inc. registered in the United States and in other countries. All other trademarks are the property of their respective owners.
Corporate Office Trimble Inc. 935 Stewart Drive Sunnyvale, CA94085 USA www.trimble.com US Location Trimble, Inc. 4450 Gibson Dr Tipp City OH 45371 USA Trimble, Inc. Europe Trimble, Inc. Europe Box 64, SE-182 11 Danderyd, Sweden Global technical support To request detailed technical assistance for Trimble solutions, contact: trimble_support@trimble.com Copyright and trademarks ©2021-2021, Trimble Inc. All rights reserved. Trimble and the Globe & Triangle logo and Access are trademarks of Trimble Inc.
5683 CC Best The Netherlands Taiwan – Battery Recycling Requirements The product contains a Lithium-ion battery. Taiwanese regulations require that waste batteries are recycled. 廢電池請回收 Regional compliance Australia and New Zealand This product conforms with the regulatory requirements of the Australian Communications and Media Authority (ACMA) Telecommunications, Radiocommunications and EMC Labelling Notices,thus satisfying the requirements for RCM marking and sale within Australia and New Zealand.
Importer of Record Trimble European Regional Fulfillment Center Logistics Manager Trimble Europe B.V. & Trimble International B.V. Industrieweg 187a 5683 CC Best The Netherlands Trimble EC Trimble Germany Am Prime Parc 11 65479 Raunheim Germany CAUTION: Only approved accessories may be used with this equipment. In general, all cables must be high quality, shielded, correctly terminated and normally restricted to two meters in length.
énumérés ci-dessous avec le gain maximum admissible indiqué. Types d'antennes non inclus dans cette liste, ayant un gain supérieur au gain maximum indiqué pour cette type, sont strictement interdits pour une utilisation avec cet appareil. Avertissement: i. les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux ii.
Product and is not sold. The terms of the end user license agreement, as included below, govern the use of the Product Software, including any differing limited warranty terms, exclusions and limitations, which shall control over the terms and conditions set forth in the limited Product warranty.
ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF DEALING WHICH DEVELOPS OR HAS DEVELOPED BETWEEN YOU AND TRIMBLE. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU. NOTE: THE ABOVE TRIMBLE LIMITED WARRANTY PROVISIONS WILLNOT APPLY TO PRODUCTS PURCHASED IN THOSE JURISDICTIONS (E.G.
to the Product Software that Trimble releases and makes commercially available and for which it does not charge separately, subject to the procedures for delivery to purchasers of Trimble products generally. If you have purchased the Product from an authorized Trimble dealer rather than from Trimble directly, Trimble may, at its option, forward the software Fix to the Trimble dealer for final distribution to you.
governing law. 3.2 Section 3.1 notwithstanding, if you acquired this product in Canada,this EULAis governed by the laws of the Province of Ontario, Canada. In such case each of the parties to this EULAirrevocably attorns to the jurisdiction of the courts of the Province of Ontario and further agrees to commence any litigation that may arise under this EULAin the courts located in the Judicial District of York, Province of Ontario.
Introduction Trimble EMPOWER is an ecosystem of rugged platform devices along with sensor and communication modules, together creating a host solution targeted at specific workflows. As an example a TSC7 combined with an EM120 radio module creates a controller solution able to connect and communicate with a Trimble Robotic total station. The Trimble Empower Data Bridge (EDB10) is a “sled” that takes the Empower concept further to allow an EMPOWER module to not only be used in EMPOWER hosts (e.
Parts of the EDB10 Data Bridge Front View
Rear View
What's in the box ● ● ● ● ● EDB10 data bridge USB-C Charging/Firmware cable A/C Adapter and International connectors Module screwdriver Quick Start Guide Charging Battery 1. Connect the USB Charging cable to the AC adapter, and plug into power. 2. Plug in the EDB10 to the charging cable 3. Charge for six hours or until fully charged. Connecting EDB10 to an EMPOWER module 1. Before connecting an EDB10 to an Empower Module, please ensure the EDB10 is powered off.
The screws on the Empower module will align with the screw holes on the EDB10. 3. Tighten the two screws located using the (provided) Module screwdriver. To prevent damage to the EDB10, do not overtighten the screws. The Empower Module and the EDB10 should form a firm connection.
Description Founders has two buttons located on the side of the Founders unit. The green button controls power, and the black button or action button is designed to work in conjunction with the Empower Module when it is attached to the EDB10 unit.
LED 1 - Empower Module LED 1 Description This LED indicates the interaction between the Empower module and external device. LED 1 Empower Module Behavior with EM120 LED 1 Empower/Data EM120 attached to EDB10 EM120 active data connection with radio Error No Empower Module attached LED Color LED State YELLOW Solid GREEN Solid RED Solid LED OFF LED 2.
LED 2 Sequencing Sequencing when EDB10 is powered on and charging Note, the connected state in the above table shows the EDB10 connected via Bluetooth. Other connection states will display different colors as below. LED’s will display in 0.5, 1.0 or 2.0 second increments as below.
Bluetooth Pairing When the EDB10 is switched on the unit will be discoverable and will be ready to be paired. LED 2 “connection state” will be white indicating the unit is not connected and is ready to pair. The EDB10 is discoverable when not connected to a device. A pairing code is not required to pair with the EDB10. When pairing with the EDB10 with a data collector “device”, the EDB10 will have the name EDBXXXXXX, where XXXXXX are the last 6 digits of the EDB10 serial number.
Once the Trimble radio is connected, the EDB10 connection to the Data collector device is essentially transparent. An application can send and receive data using the radio link solution upon request. Data received from the remote radio connection will be transmitted to the data collector via the connection with the EDB10. Revision History Date Revision Author 08-05-20 1 Bruce Hook 4/14/21 1.
