User's Manual

ManualsBrandsTriMark ManualsElectronicsEASK.CAN RF

e-ASK

Electronic Access Security Keyless-entry

e-ASK Keyless-entry System

Installation & Instructions

(UM26 ~ 24324-02)

Rev. B

9/08

Table of Contents

Introduction .............................................................................................3

Standard e-FOB Operation and Features .............................................3

Cargo e-FOB Operation and Features ..................................................4

Non-doorbell e-PAD Operation and Features ......................................5

Locking doors with keypad ...................................................................5

Secure Operations................................................................................5

e-ASK CAN DIP Switch Configuration –...............................................6

Configuration A [SW 4 off / SW 5 off / SW 6 off]: .............................6

Configuration B [SW 4 off / SW 5 off / SW 6 on]: .............................6

Configuration C [SW 4 off / SW 5 on / SW 6 off]:.............................6

Configuration D [SW 4 off / SW 5 on / SW 6 on]: .............................7

Configuration A [SW 4 off / SW 5 off / SW 6 off]: .............................7

Configuration B [SW 4 off / SW 5 off / SW 6 on]: .............................7

Configuration C [SW 4 off / SW 5 on / SW 6 off]:.............................7

Configuration D [SW 4 off / SW 5 on / SW 6 on]: .............................7

Additional Features.................................................................................8

Dome/Porch Light Activation ................................................................8

e-PAD Anti-tamper Deactivating Feature .............................................8

e-Grab Handle Lighting.........................................................................8

Trim Pot Variable Resistors ..................................................................9

Learn Switch Connector .......................................................................9

Status LED............................................................................................9

Miscellaneous I/O Module Features .....................................................9

Door locking and unlocking ..............................................................9

Lock and Unlock Confirmation..........................................................9

Deactivate Lock Confirmation.........................................................10

Door Ajar Warning ..........................................................................10

Alarm ..............................................................................................10

Timed Dome/Porch Light Activation ...............................................11

Compartment Light Activation ........................................................11

Auxiliary 1 Output Activation...........................................................11

Teaching Additional Transmitter FOBs ..............................................12

Teaching Keypad New Authority / Access Codes .............................14

Assign New Access Codes.................................................................15

Troubleshooting ....................................................................................16

Appendix A: Connectors and Pinouts ...............................................XX

Summary of content (12 pages)

PAGE 1
Table of Contents Introduction .............................................................................................3 Standard e-FOB Operation and Features .............................................3 Cargo e-FOB Operation and Features ..................................................4 Non-doorbell e-PAD Operation and Features ......................................5 Locking doors with keypad ...................................................................5 Secure Operations ...................
PAGE 2
Introduction This manual provides the necessary information for the proper installation and use of TriMark’s CAN e-ASK system including vehicle module and keypad. Cargo e-FOB Operation and Features Button Entry Lock Entry Unlock Cargo Lock Cargo Unlock Note: • Standard e-FOB Operation and Features Button Lock Unlock Panic * Auxiliary Button 3 • Function Locks entry door and arms security system. Unlocks entry door and disarms security system. Also activates the porch light.
PAGE 3
Non-doorbell e-PAD Operation and Features The e-PAD is shipped with default authority and access codes. Unless the OEM or dealer has changed default codes, the authority and access codes are as follows: Access code: Digit 1 Digit 2 1/2 3/4 Digit 3 5/6 Digit 4 7/8 Digit 5 9/0 Authority code: Digit 1 Digit 2 7/8 7/8 Digit 3 7/8 Digit 4 7/8 Digit 5 7/8 Locking doors with keypad Press and hold down the (1 / 2) or (1) button for 1-2 seconds. An access code is not needed to lock the doors.
PAGE 4
Configuration D [SW 4 off / SW 5 on / SW 6 on]: • Button (1/2): Unlocks all entry doors • Button (3/4): Unlocks all entry and compartment doors • Button (5/6): Unlocks all curb side compartment doors (relay banks C-D) • Button (7/8): Unlocks all driver side compartment doors (relay banks A-B) • Button (9/0): Toggles Aux 1 output • Interior Switch Dip Switch Setting Configurations: The following vehicle switch assignments of connector J1 and 3 define functional assignment of interior switches.
PAGE 5
Trim Pot Variable Resistors These trim pots provide adjustable settings for timed outputs. Clock-wise rotation increases activation time. See Appendix B, page IV. • • • Dome/porch light activation (5-60 second range). Auxiliary 1 output (0.5-5.0 minute range). Auxiliary 2 compartment lighting output (0.5-5.0 minute range). • a lock command. On unlock, the headlights flash twice and the horn honks twice. Locking and unlocking confirmation is deactivated while engine is running.
PAGE 6
Siren Single Lock confirmation Not used All Lock confirmation Not used 1 minute or when shut off Horn 1 chirp 2 chirps Not used Headlights 1 flash 2 flashes 1 minute or when shut off Outputs Alarm Timed Dome/Porch Light Activation The dome/porch light is activated upon pressing any keypad button or by unlocking entry door via FOB transmitter. The activation duration is controlled via trim pot. Starting the engine or locking the doors deactivates the light.
PAGE 7
Teaching Keypad New Authority / Access Codes 7. Press any fob button until LED pattern changes (longer ~0.5 second flash), then release. This synchs the first fob transmitter. nd 8. Press any fob button of 2 fob, LED pattern changes nd immediately. This synchs the 2 fob transmitter. 9. Repeat above step 8 until all fobs are synched (up to 4 fobs) 10. Remove power and CAN connector from door module 11. Move DIP switches 4-6 to normal position and verify DIP switches 1-3 are in proper position.
PAGE 8
Assign New Access Codes With a valid authority code (see page 3 or 11), an access code can be programmed with the following instructions. 1. Press the (5/6) button for 5 seconds, the keypad will beep. The backlighting LED of the keypad will flash indicating the learn mode. 2. Enter in the 5-digit authority code (see page 3 or 11). Keypad will provide a long beep that will stop after you have defined an access number. 3. Press and release the button that corresponds to the access number.
PAGE 9
Setting CAN Keypad Function Instance (location): The following procedure sets the keypad’s CAN function instance which determines the default CAN address it will try to claim and identifies this keypad’s location within the vehicle. Each keypad installed in a vehicle must have a unique function instance. The default function instance is 0. The procedure for assigning keypad function instance follows: 1. Ground the learn mode input (brown wire). AMP connector housing location 9.
PAGE 10
Access code is not recognized Key fob works correctly, keypad beeps, but no output Unexpected, secure operation occurs Verify that code has not been changed. Reassign keypad with instructions starting on page 11. Confirm use of an access code, not the authority code. Cycle power to I/O module. Verify DIP switches are set to correct configuration setting. Output relay latches on or off.
PAGE 11
LOCK ALL INPUT (GND) 11 UNASSIGNED 9 LOCK ENTRY INPUT (GND) 12 GROUND 10 SECURITY INPUT (GND) 13 UNASSIGNED 14 BANK C LOCK (RELAY 25A) 1 UNASSIGNED 15 BANK B LOCK (RELAY 25A) 2 GROUND 16 BANK A UNLOCK (RELAY 25A) 3 BANK D LOCK (RELAY 30A) 17 BANK B UNLOCK (RELAY 25A) 4 BANK D UNLOCK (RELAY 30A) 18 BANK C UNLOCK (RELAY 25A) 5 VEHICLE POWER 19 BANK A LOCK (RELAY 25A) 6 CAN HIGH 20 LOCK ENTRY OUTPUT (RELAY 30A) 21 EXTERNAL RELAY POWER (+12V) 1 CAN LOW 22 HORN OUTPUT (-
PAGE 12
FCC ID: TV2ERX3 FCC Compliance and Advisory Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules.