SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY User Guide CPE (SC1010) Version 1.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY User Guide .......................................................................................................................... 1 CPE (SC1010)..................................................................................................................... 1 1 Introduction................................................................................................................. 3 1.1 Outdoor CPE....................................................
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 1 Introduction The SkyPilot CPE (SC1010) provides a subscriber interface to a SkyPilot wireless network. The SkyPilot CPE connects either to a SkyPilot Seed (SD1010) or directly to a SkyPilot Gateway (GW1010) device. The SkyPilot CPE operates in the unlicensed 5.8GHz UNII band and comes in Indoor and Outdoor variants. The Indoor and Outdoor SkyPilot CPE differ only in the external mechanical packaging.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 1.1 Outdoor CPE The Outdoor CPE is a fully integrated, environmentally hardened device providing the interface between a wireless SkyPilot network and the local subscriber. The subscriber connection is via a single 10/100bT Ethernet port. The CPE connects to the SkyPilot network via a single, optimized wireless link.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 1.2 Indoor CPE The Indoor CPE contains the same antenna and circuitry as the Outdoor CPE. The external mechanicals are replaced with an attractive, consumer friendly plastic housing. The Indoor CPE may be used with either the desk or window mount provided. The LEDs provide feedback allowing for the easy placement and pointing of the unit. As with the Outdoor CPE, the Indoor unit provides full operator monitoring and management.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 2 Network Architecture The SkyPilot CPE (SC1010) combines with the Gateway (GW1010) and Seed (SD1010) to create a robust, high capacity wireless network. All wireless links within the network are established and optimized automatically. Seed units allow for expanded coverage and permit multiple paths through the network. A highly efficient routing algorithm selects the best path for user traffic and heals around any network failures. 2.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 2.3 Networking The SkyPilot system operates as a Layer 2 network. The Gateway and CPE have an Ethernet bridge. All upstream subscriber traffic is direct out the Gateway Ethernet port and to external switch or router. All SkyPilot network elements implement a SNMPv2c agent. In addition, there is also a CLI that may be access locally via a serial port or remotely via Telnet. In order to support these interfaces, an IP address must be allocated.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 3 Installation The SkyPilot CPE is designed for a wide range of installations. The Indoor CPE can be user installed in a home or office. The Outdoor CPE can easily be installed on the roof or exterior wall of an office, apartment build or single family home. The Outdoor CPE can also be very easily installed on a light or utility pole. 3.1 3.1.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY Once the best location has been identified, then the user must mount the CPE. If there is a suitable desk, bookshelf or other flat surface, then the desk mount may be utilized. The user should set the CPE in the cradle, ensuring the front of the unit is pointing toward the window. The CPE can be fixed in position by tightening the mounting knobs.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 3.1.2 Cabling The Indoor CPE utilizes Power over Ethernet (PoE) provided by the included Power Injector. Note that the CPE should be installed with the SkyPilot provided Power Injector only. The use of other PoE Power Injectors could result in damage to the unit. The Power Injector has three connections: 1. Power – receives power from the Power Supply. 2. CPE Connector – connects the Power Injector to the CPE via a supplied Cat5.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 3.2 3.2.1 Outdoor CPE Mounting As with the Indoor CPE, the appropriate location for the Outdoor CPE must be found before mounting. Link quality is generally improved with an installation as high and as free of obstruction as possible. The installer should power the CPE and, using the LED indication (LED 4), find the location and direction with the best signal strength. As previously noted, knowledge of Gateway and/or Seed location(s) can speed this process.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 3.2.2 Cabling The Outdoor CPE is cabled in the same manner as the Indoor CPE. Note that it is recommended that the Power Injector is located indoors or a suitable weatherproof enclosure. The Outdoor CPE has a weatherproof 10/100bt Ethernet interface that includes a rubber gasket and metal cover. First the Cat5 Ethernet cable is inserted. The gasket is then placed around the cable.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 4 Configuration The SkyPilot system requires minimal configuration before service can be offered. There is the option to utilize the SkyPilot Provisioning Server or to manual configure. The Provisioning Server, with its interface to an SQL database facilities the configuration of large scale networks. The Provisioning Server is the topic of a separate document. This document shall focus on the manual configuration of CPE (SC1010) units. 4.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 5 CLI The CPE (SC1010) provides a complete CLI interface. This interface may be used to configure and monitor the unit. A full definition of the CLI is available – email support@skypilot.com to request a copy. As an example, the CPE configuration screen is shown below. All other CPE parameters are read-only.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY 6 SNMP The CPE (SC1010) has a SNMPv2c agent. The following MIBs are supported: 1. 2. 3. 4. MIB-II (RFC 1213) EtherLike (RFC 2665) Bridge (RFC 1493) SkyPilot Private MIB Email support@skypilot.com to request a copy of the SkyPilot MIB.
SKYPILOT NETWORK CONFIDENTIAL AND PROPRIETARY FCC REGULATORY INFORMATION Digital Device Section of Product NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
