User Manual

ManualsBrandsTrilliant Networks ManualsElectronicsUtility Meter

RES-3000-I210+ / I210+RD / I210+c

PA-0115A Rev. 1.4

March 11th, 2011 Page 1 of 6

Introduction

This document will help the SecureMesh user to retrofit the product model RES-3000-I210+,

RES-3000-I210+RD & RES-3000-I210+c in a GE I-210+, GE I-210+RD, GE I-210+c & GE

I-210+cRD meter as intended.

Safety and Assembly Cautions

- Warning: The meter carries lethal voltages. The meter must be completely disconnected

from any external circuits. Failure to observe this practice can result in serious injury or

death.

- Caution: These devices are electrostatic sensitive. It is best to use a grounded electrostatic

mat and wrist strap to prevent electrostatic discharge.

- Important: It is not necessary to completely separate the top of the meter from the base of

the meter for this retrofit procedure. However, if the two parts are completely disconnected

and separated, it is extremely important to keep each meter component together for re-

assembly. This is due to the top section of the meter containing calibration “characterization”

programming for the CTs in the meter base. If these components get mixed up with other

meter components, current measurement errors will occur.

SecureMesh Radio Specifications:

• IEEE Standard : IEEE 802.15.4

• Power Output : +30 dBm

• Radio Sensitivity : -99 dBm

• RF Data rate : 250 kbps

• Operating Frequency : 2.400-2.483 GHz

• Network Topology : Mesh

• Modulation : O-QPSK

• Physical Dimensions : 2.54” x 3.47”

• Antenna : Dipole, 3.5 dBi

SecureMesh retrofit for GE I-210+ / I-210+RD / I-210+c / I-210+cRD meters

Summary of content (6 pages)

PAGE 1
RES-3000-I210+ / I210+RD / I210+c SecureMesh retrofit for GE I-210+ / I-210+RD / I-210+c / I-210+cRD meters Introduction This document will help the SecureMesh user to retrofit the product model RES-3000-I210+, RES-3000-I210+RD & RES-3000-I210+c in a GE I-210+, GE I-210+RD, GE I-210+c & GE I-210+cRD meter as intended. Safety and Assembly Cautions - Warning: The meter carries lethal voltages. The meter must be completely disconnected from any external circuits.
PAGE 2
RES-3000-I210+ / I210+RD / I210+c Industry Canada Compliance Statement (English & French) This device complies with industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 3
RES-3000-I210+ / I210+RD / I210+c FCC Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
RES-3000-I210+ / I210+RD / I210+c Procedure Note: In this procedure, the “I-210+” wording will be used for all 4 meter designations: I-210+, I-210+RD, I-210+c & the I-210+cRD meters. The following table represents the Trilliant SecureMesh product associated to the GE meter: • RES-3000-I-210+ product must be installed into an I-210+ meter • RES-3000-I-210+RD product must be installed into an I-210+RD meter. • RES-3000-I-210+c product can be installed into an I-210+c or I-210+cRD meter. 1.
PAGE 5
RES-3000-I210+ / I210+RD / I210+c 3. Install the SecureMesh board by first inserting the female connector in the I-210+ male connector as shown. Align the 2 HEX Aluminum posts with the 2 holes in the GE I210+ meter faceplate. Male-Female connector mating 4. Attach the two mounting screws (HS-0013I) through the faceplate into the 2 HEX posts so that the SecureMesh board is held securely in place. Torque screws to 2 +/-0.2 Inch pounds. Screws (For Trilliant internal use: Milwaukee #2) PA-0115A Rev. 1.
PAGE 6
RES-3000-I210+ / I210+RD / I210+c 5. Affix any missing label on the meter faceplate, finalize inspection & test as required Note: if this label is supplied by Trilliant, use HI0274A for the I-210+ or HI-0275A for the I-210+RD or HI-0345A for the I-210+c. 6. Reassemble the I-210+ clear cover on its base. 7. Perform functional test & configuration as required. PA-0115A Rev. 1.