User Manual

ManualsBrandsTrilliant Networks ManualsElectronicsWireless Electric Meter

RES-3000-Focus

PA-0129A Rev. 1.0

June 18, 2010 Page 1 of 4

RES-3000-FocusAX

Introduction

This document will help the SecureMesh user to retrofit the product model RES-3000-

Focus/FocusAX in a Landis &Gyr Focus® meter as intended.

Safety and Assembly Cautions

- Warning: The meter carries lethal voltages. The meter must be completely

disconnected from any external circuits. Failure to observe this practice can result in

serious injury or death.

- Caution: These devices are electrostatic sensitive. It is best to use a grounded

electrostatic mat and wrist strap to prevent electrostatic discharge.

- Important: It is not necessary to completely separate the top of the meter from the base

of the meter for this retrofit procedure. However, if the two parts are completely

disconnected and separated, it is extremely important to keep each meter component

together for re-assembly. This is due to the top section of the meter containing

calibration “characterization” programming for the CTs in the meter base. If these

components get mixed up with other meter components, current measurement errors will

occur.

Material

• Focus meter (must be AMR configured)

• Trilliant SecureMesh RES-3000-

Focus/FocusAX .

• Mounting Screws - QTY=3 (provided by

L&G,

ref.Trilliant # HS-0029B & HS-0029C)

• Self-Retaining Spacers-QTY=3

(provided by L&G, ref. Trilliant # HE-

0033C & HE-0033D)

• Serial # & FCC/IC label (provided by

L&G, ref Trilliant #.: HI-0307A)

SecureMesh retrofit for Focus/FocusAX meter

Summary of content (4 pages)

PAGE 1
RES-3000-Focus RES-3000-FocusAX SecureMesh retrofit for Focus/FocusAX meter Introduction This document will help the SecureMesh user to retrofit the product model RES-3000Focus/FocusAX in a Landis &Gyr Focus® meter as intended. Safety and Assembly Cautions - Warning: The meter carries lethal voltages. The meter must be completely disconnected from any external circuits. Failure to observe this practice can result in serious injury or death. - Caution: These devices are electrostatic sensitive.
PAGE 2
RES-3000-Focus RES-3000-FocusAX Procedure 1. If it is not already done, dis-assemble the Focus meter clear cover and unsnap the base from the top portion of the case to access the 3 post receptacle holes in the Top Portion and the Focus/FocusAX board connector as shown. Male Interface connector Meter TOP portion Post receptacles HE-0033C Short Spacer 2. Snap the 3 plastic spacers into the Trilliant SecureMesh RES-3000Focus/FocusAX PCB as showm.
PAGE 3
RES-3000-Focus RES-3000-FocusAX 4. Attach the three (3) mounting screws through the SecureMesh PCB into the 3 plastic spacers so that the SecureMesh board is held securely in place. Screw Ref: HS-0029B Screw Ref: HS-0029B Screw Ref: HS-0029C 5. Affix any missing label (Ref.: HI-0307A) on the meter Top Portion, finalize inspection & test as required 6. Reassemble the Focus Top portion by snapping it into the bottom portion and affix the clear cover on its base. 7. Perform functional test. PA-0129A Rev.
PAGE 4
RES-3000-Focus RES-3000-FocusAX SecureMesh Radio Specifications: • • • • • • • • • IEEE Standard : Power Output : Radio Sensitivity : RF Data rate : Operating Frequency : Network Topology : Modulation : Physical Dimensions : Antenna : IEEE 802.15.4 +30 dBm -99 dBm 250 kbps 2.400-2.483 GHz Mesh O-QPSK 2.33” x 4.70” Dipole, 3.5 dBi Industry Canada and Federal Communication Commission Compliance Statement This device complies with Part 15 of the FCC Rules.