Advanced Wireless Test Set Current Date/Time The Current Date/Time setting is used to set the current date and time for the 802 AWE. This information is displayed in the Title Bar of any navigation screen and is added to every data log, measurement, job, and Survey. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the current date in the mm/dd/yyyy format.
Advanced Wireless Test Set Timezone The Timezone setting allows you to set the time zone of the 802 AWE. This is useful when using the instrument in areas that automatically adjust their local time based on Daylight Savings Time (DST). Press the Enter button and the Set Timezone window will be displayed as shown in the image to the right. Use the up/down arrow buttons to choose the desired timezone and then press the Enter button to select the timezone. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set User Settings Select the User button as shown in the image to the right to adjust the user information that is associated with the currently logged in user of the 802 AWE. The User screen will be displayed as shown in the image to the right. This screen allows you to modify the user settings of the currently logged in user of the 802 AWE. From within the User screen, use the left/right arrow buttons on the keypad to navigate through the list of setup items.
Advanced Wireless Test Set User Name The User Name setting is used to set the user name for the user profile that is currently logged into the 802 AWE. This information is displayed on the welcome screen and is added to every data log, measurement, job, and survey. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the user name. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Company The Company setting is used to set the company name for the user profile that is currently logged into the 802 AWE. This information is displayed on the welcome screen and is added to every data log, measurement, job, and survey. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the company name. 802 AWE Operation Manual Page II-22 www.trilithic.
Advanced Wireless Test Set Tech ID The Tech ID setting is used to set the technician ID for the user profile that is currently logged into the 802 AWE. This information is displayed on the welcome screen and is added to every data log, measurement, job, and survey. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the technician ID. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Interface Settings Select the Interface button as shown in the image to the right to adjust the interface settings for the currently logged in user of the 802 AWE. The Interface screen will be displayed as shown in the image to the right. This screen allows you to modify the user interface settings. From within the Interface screen, use the left/right arrow buttons on the keypad to navigate through the list of setup items. 802 AWE Operation Manual Page II-24 www.trilithic.
Advanced Wireless Test Set LCD Dimming Delay The LCD Dimming Delay setting is used to conserve power by automatically dimming the display screen backlight after the 802 AWE has been idle for a specified period of time. The default setting for the LCD dimming delay is 1 Minute. The LCD dimming delay can be set from a minimum of one (1) minute up to a maximum of five (5) minutes.
Advanced Wireless Test Set Sleep Mode Delay The Sleep Mode Delay setting is used to conserve power by automatically enabling the sleep mode after the 802 AWE has been idle for a specified period of time. The default setting for the sleep mode delay is 5 Minutes. The sleep mode delay can be set from a minimum of one (1) minute up to a maximum of 60 minutes. Use either of the following methods to change the sleep mode delay: • Use the up/down arrow buttons to change the value in one (1) minute increments.
Advanced Wireless Test Set Turn Off Delay The Turn Off Delay setting is used to conserve power by automatically turning off the device after the 802 AWE has been idle for a specified period of time. The default setting for the turn off delay is 1 Hour. The turn off delay can be set from a minimum of one (1) hour up to a maximum of 24 hours. Use either of the following methods to change the turn off delay: • Use the up/down arrow buttons to change the value in one (1) hour increments.
Advanced Wireless Test Set Keypad Beeps The Keypad Beeps setting is used to enable or disable keypad beeps for the internal speaker. The default setting for Keypad Beeps is Yes, use the up/down arrow buttons to select from the following preset values: • Select Yes to hear the keypad beeps. • Select No to mute the keypad beeps. 802 AWE Operation Manual Page II-28 www.trilithic.
Advanced Wireless Test Set Keypad Delay The Keypad Delay setting is used to adjust the keypad delay. The default setting for the keypad delay is 300 mSeconds. The keypad delay can be set from a minimum of 100 mSeconds up to a maximum of 1000 mSeconds. Use either of the following methods to change the keypad delay: • Use the up/down arrow buttons to change the value in 50 mSecond increments.
Advanced Wireless Test Set Keypad Rate The Keypad Rate setting is used to adjust the keypad rate. The default setting for the keypad rate is 50 mSeconds. The keypad rate can be set from a minimum of 50 mSeconds up to a maximum of 1000 mSeconds. Use either of the following methods to change the keypad rate: • Use the up/down arrow buttons to change the value in 50 mSecond increments.
Advanced Wireless Test Set Job & Workorder ID Length The Job/Workorder ID Length setting is used to set the maximum number of characters to display for jobs and workorders on the 802 AWE. The default setting for the job and workorder ID length is 6 Characters. The character length can be set from a minimum of 6 characters up to a maximum of 32 characters.
Advanced Wireless Test Set Language The 802 AWE can be equipped to work in various languages. The default language is defined by the Global menu and shows here as Meter Default, but can be adjusted per user. Use the up/down arrow buttons to select from the following languages. • Meter Default • English • Spanish • Portuguese • Chinese • Chinese (Simplified) • Japanese If you have other language options available on your instrument, you can change the default language.
Advanced Wireless Test Set Ethernet Settings Select the Ethernet button as shown in the image to the right to view/edit the Ethernet settings for the 802 AWE. The Ethernet screen will be displayed as shown in the image to the right. This screen allows you to modify the Ethernet connection settings. From within the Ethernet screen, use the left/right arrow buttons on the keypad to navigate through the list of setup items. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Prompt User The Prompt User setting is used to prompt a user with the Network Settings window before connecting to a network. The default setting for Prompt User is Yes, use the left/right arrow buttons to select from the following preset values: • Select Yes to prompt the user with the Network Settings window before connecting to a network. • Select No to automatically connect using the default network settings.
Advanced Wireless Test Set Address / Prefix When IP Mode is set to IPv4 Static, the Address / Prefix setting is used to set the IP address of the network connection. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the IP Address in the ###.###.###.### format. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Subnet / Netmask When IP Mode is set to IPv4 Static, the Subnet / Netmask setting is used to set the subnet address of the network connection. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the subnet address in the ###.###.###.### format. 802 AWE Operation Manual Page II-36 www.trilithic.
Advanced Wireless Test Set Gateway / Route When IP Mode is set to IPv4 Static, the Gateway / Route setting is used to set the subnet address of the network connection. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the gateway address in the ###.###.###.### format. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Primary DNS When IP Mode is set to IPv4 Static, the Primary DNS setting is used to set the primary domain name server address of the network connection. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the primary DNS address in the ###.###.###.### format. 802 AWE Operation Manual Page II-38 www.trilithic.
Advanced Wireless Test Set Secondary DNS When IP Mode is set to IPv4 Static, the Secondary DNS setting is used to set the secondary domain name server address of the network connection. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the secondary DNS address in the ###.###.###.### format. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Wi-Fi Settings Select the Wi-Fi button as shown in the image to the right to view/edit the Wi-Fi settings for the 802 AWE. The Wi-Fi screen will be displayed as shown in the image to the right. This screen allows you to modify the Wi-Fi connection settings. From within the Wi-Fi screen, use the left/right arrow buttons on the keypad to navigate through the list of setup items.
Advanced Wireless Test Set Current Access Point The Current Access Point setting is used to set the SSID of the default Wi-Fi network. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the name of the access point. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Current Password The Current Password setting is used to set the password of the default Wi-Fi network. Press the Enter button and the Virtual Keyboard will be displayed as shown in the image to the right. Use the Virtual Keyboard to enter the password of the Wi-Fi network. 802 AWE Operation Manual Page II-42 www.trilithic.
Advanced Wireless Test Set Current Security The Current Security setting is used to set the security of the selected Wi-Fi network. The default setting for Current Security is Auto, use the left/right arrow buttons to select from the following preset values: • Auto – This will automatically set the security protocol of the Wi-Fi access point. • WEP 40/64 – This is the Wired Equivalency Privacy (WEP) security protocol with a 40 or 64 bit hexadecimal security key.
Advanced Wireless Test Set Select Default Access Point Highlight the desired access point from the access points table and then select the Activate softkey. The Continue window will be displayed as shown in the image to the right. Select the OK button to continue or select the Cancel button to exit without setting the default access point. 802 AWE Operation Manual Page II-44 www.trilithic.
Advanced Wireless Test Set Delete a Saved Access Point Highlight the desired access point from the access points table and then select the Delete softkey. The Continue window will be displayed as shown in the image to the right. Select the OK button to continue or select the Cancel button to exit without deleting the saved access point. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Bluetooth Settings Select the Bluetooth button as shown in the image to the right to view/edit the Bluetooth settings for the 802 AWE. The Bluetooth screen will be displayed as shown in the image to the right. This screen allows you to modify the Bluetooth connection settings. From within the Bluetooth screen, use the left/right arrow buttons on the keypad to navigate through the list of setup items.
Chapter 4 Advanced Wireless Test Set File Management Overview Select the Files icon as shown in the image to the right to view the files that are stored in the internal memory of the 802 AWE. The File Explorer screen will be displayed as shown in the image to the right.
Advanced Wireless Test Set Database Backup Backup to Internal Memory Perform the following steps to backup the 802 AWE database file to the internal memory of the 802 AWE: 1. Select the Database softkey. 2. From the Database pop-up menu, select the Backup button as shown in the image to the right. 3. The Status Bar will indicate a successful backup to the internal memory by displaying the text “-> /tmp/main.db” as shown in the image below.
Advanced Wireless Test Set Backup to USB Flash Drive Perform the following steps to backup the 802 AWE database file to a USB flash drive: 1. Insert the USB flash drive adapter into the USB port of the 802 AWE 2. Then insert a USB flash drive into the USB flash drive adapter. 3. Press the Function button and select the Activate USB Power function as shown in the image to the right. 4.
Advanced Wireless Test Set 7. The Message Bar will indicate a successful backup to the flash drive by displaying the text “-> /media/sda1/main.db” as shown in the image below. This function is useful when cloning the device settings between different meters. When importing the database file on another meter, all device settings will be updated while retaining the existing user information.
Advanced Wireless Test Set Restore from USB Flash Drive Perform the following steps to restore the 802 AWE database file from a USB flash drive: 1. Insert the USB flash drive adapter into the USB port of the 802 AWE. 2. Insert a USB flash drive into the USB flash drive adapter. 3. Press the Function button and select the Activate USB Power function as shown in the image to the right. 4.
Advanced Wireless Test Set Cloning Meter Settings to a New Meter Perform the following steps to clone all files from one 802 AWE to another: 1. Insert the USB flash drive adapter into the USB port of the 802 AWE. 2. Insert a USB flash drive into the USB flash drive adapter. 3. Press the Function button and select the Activate USB Power function as shown in the image to the right. 4.
Advanced Wireless Test Set 5. Select the Database softkey. 6. From the Database pop-up menu, select the Backup button as shown in the image to the right. 7. The Message Bar will indicate a successful backup to the flash drive by displaying the text “-> /media/sda1/main.db” as shown in the image to the right. 8. Press the Function button and select the Deactivate USB Power function as shown in the image to the right. 9. Remove the USB flash drive and adapter from the meter to clone. 10.
Advanced Wireless Test Set 12. Press the Function button and select the Activate USB Power function as shown in the image to the right. 13. The power to the USB flash drive is activated and the drive is now mounted to the file system as shown in the image to the right. The 802 AWE is now capable of transferring files to and from the USB flash drive. 14. Select the Database softkey. 15. From the Database pop-up menu, select the Restore button. 16. The clone process is now complete.
Advanced Wireless Test Set Import ViewPoint Files from a USB Flash Drive Perform the following steps to import a ViewPoint package file from a USB flash drive: 1. Insert the USB flash drive adapter into the USB port of the 802 AWE. 2. Then insert a USB flash drive into the USB flash drive adapter. 3. Press the Function button and select the Activate USB Power function as shown in the image to the right. 4. Select the File softkey. 5.
Advanced Wireless Test Set 8. A confirmation window will be displayed as shown in the image to the right. If you have existing ViewPoint files on the meter, it will ask if you want to replace them. 9. Select the Yes button to import the file and replace existing files or select No to keep the existing package files and import the new package. 10.
Advanced Wireless Test Set Export a File Perform the following steps to export a single file to a USB flash drive: 1. Insert the USB flash drive adapter into the USB port of the 802 AWE 2. Then insert a USB flash drive into the USB flash drive adapter. 3. Use the arrow buttons to highlight the file that you would like to export. 4. Select the File softkey. 5. From the File pop-up menu, select the Export button as shown in the image to the right. 6.
Advanced Wireless Test Set Export All Files Perform the following steps to export all files to a USB flash drive: 1. Insert the USB flash drive adapter into the USB port of the 802 AWE 2. Then insert a USB flash drive into the USB flash drive adapter. 3. Select the File softkey. 4. From the File pop-up menu, select the Export All button as shown in the image to the right. 5. The 802 AWE will automatically connect to the attached USB flash drive as shown in the image to the right. 6.
Advanced Wireless Test Set 8. Use the Virtual Keyboard to enter the name of the new export file as shown in the image to the right. 9. Later when you are ready to import, you will see the file listed in the ViewPoint files on the USB flash drive, as shown here. 802 AWE Operation Manual www.trilithic.
Advanced Wireless Test Set Delete Files Perform the following steps to delete files from the internal memory of the 802 AWE: 1. Use the arrow buttons to highlight the file you want to delete. 2. Select the File softkey. 3. From the File pop-up menu, select the Delete button as shown in the image to the right. 4. The Continue window will be displayed as shown in the image to the right. 5. Select the OK button to delete the file or select the Cancel button to exit without deleting the file.
Advanced Wireless Test Set Function Menu Options Additional functions can be accessed from within the File Explorer screen by pressing the Function button. The Function menu will be displayed as shown in the image to the right and includes the following functions specifically for the File Explorer screen. Activate USB Power This function is used to activate power to the USB flash drive inserted into the USB port of the 802 AWE. The USB flash drive must be enabled before being able to be used.
Advanced Wireless Test Set Deactivate USB Power This function is used to deactivate power to the USB flash drive inserted into the USB port of the 802 AWE. The USB flash drive should be deactivated before removing. Select the Deactivate USB Power button from the Function menu. The USB flash drive can now be removed. The 802 AWE automatically deactivates the power to the USB flash drive when you exit the File Explorer screen.
Advanced Wireless Test Set 2. The Message Bar will indicate a successful save to the internal memory of the 802 AWE by displaying the text “-> /tmp/slm360log.txt” as shown in the image to the right. Save to a USB Flash Drive This function is used primarily for remote troubleshooting with the Trilithic Applications Support Department. This file can be emailed to Trilithic for advanced troubleshooting. Perform the following steps to save the 802 AWE log file to a USB flash drive: 1.
Advanced Wireless Test Set 5. Select the Save Log softkey. 6. The Message Bar will indicate a successful save to the flash drive by displaying the text “-> /media/sda1/slm360log.txt” as shown in the image to the right. 802 AWE Operation Manual Page II-64 www.trilithic.
Chapter 5 Advanced Wireless Test Set Firmware Updates Overview Before updating the firmware, make sure the battery is fully charged or the meter is powered via the AC to DC Power Adapter & Battery Charger. Select the Update FW icon as shown in the image to the right to update the firmware of the 802 AWE. The Update Firmware screen will be displayed as shown in the image to the right. This screen allows you to perform a firmware update.
Advanced Wireless Test Set Update Firmware from Website Perform the following steps to update the 802 AWE firmware from a website: 1. Select the Accept softkey. 2. From the Accept pop-up menu, select the Web Firmware button as shown in the image to the right. 3. If the firmware installed in the 802 AWE is current, the Information window will be displayed as shown in the image to the right. Select the OK button to return to the previous screen. 4.
