RS9110-N-11-03 Evaluation Board User Guide Ver sion 1.5 Version August 2011 Redpine Signals, Inc. 2107 N. First Street, #680 San Jose, CA 95131. Tel: (408) 748-3385 Fax: (408) 705-2019 Email: info@redpinesignals.com Website: www.redpinesignals.com Redpine Signals, Inc.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version Disclaimer The information in this document pertains to information related to Redpine Signals Inc. products. This information is provided as a service to our customers, and may be used for information purposes only. Redpine assumes no liabilities or responsibilities for errors or omissions in this document.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version Table of Contents 1: Introduction.......................................................................5 : Wi-Fi Data Transfer Tests...................................................6 .1: .2: .3: .4: .5: .6: .7: Test Setup.............................................................................6 Evaluation Software – Windows XP.......................................
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version Table of Figures Figure 1: RS9110-N-11-03 Evaluation Board and Connectors.........................5 Figure 2: RF Cable Connected to the RS9110-N-11-03 Evaluation Board........6 Figure 3: Test Setup for Throughput Measurement.........................................7 Redpine Signals, Inc.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version 1: Introduction The RS9110-N-11-03 evaluation board provides a complete IEEE 802.11abgn Wireless LAN evaluation platform. This basically has the RS9110-N-11-03 IEEE 802.11abgn WLAN module mounted on it along with few other supporting components such as 40 MHz reference oscillator and other passives. The RS9110-N-11-03 is a high-performance, low-power WLAN module.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version A probe point (Jumper PB9) is provided in order to measure the total power consumed by the RS9110-N-11-03 module during transmit, receive, and standby modes. On board resistors are provided for the Mode Select, which helps the user to switch from the SDIO host interface to SPI host interface. A JTAG Connector is also provided to debug process flow control of the evaluation board.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version Please note that, in order to evaluate the Lite-Fi™ on a Windows CE or a Windows Mobile platform, you need to replace the Laptop in the following setup, with any of the Windows CE or Windows Mobile based SDIO platform. SDIO Laptop with SDIO slot RS9110-N-11-03 EVB 802.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version Installation of the setup file Host requirements to install the Wi-Fi driver Installation of the Wi-Fi driver RS9110_N_11_03_WLAN _Test_Procedure_Window sXP_V1_0.pdf This is a user guide on the usage of the driver and wireless configuration utility to do data transfer tests under following categories: 11g connection with WPA/WPA2 11n connection with WPA2 11n connection with Aggregation .
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version Deliverable Description Linux platform: 11g connection with WPA/WPA2 11n connection with WPA2 11n connection with Aggregation .5: Evaluation Process on Linux You can start the evaluation process as follows: Step 1: - Follow the instructions mentioned in the LiteFi_Driver_Installation_Guide_Linux.pdf. Step 2: - Follow the instructions mentioned in the RS9110_N_11_03_WLAN_Test_Procedure_Linux.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version .7: Evaluation Process on Windows CE You can start the evaluation process as follows: Step 1: - Follow the instructions mentioned in the LiteFi_Driver_Installation_Guide_WindowsCE.pdf Step 2: - Follow the instructions mentioned in the RS9110_N_11_03_WLAN_Test_Procedure_WindowsCE.pdf Redpine Signals, Inc.
S9110-N-11-0 3 Eval uation B oard R RS9110-N-1103 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version 3: Connector Details This section covers the connector details of various headers. 3.1: SPI/SDIO connector The following table provides the interface details for SPI/SDIO connector. You should not install R12, for operating the evaluation board in SDIO Mode. Conversely, you need to install R12 to put the board into SPI mode. S. NO SDIO Signal Names 2SPI Signal Names Connector Pin No.
RS9110-N-11-03 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version S. No Signal Names Connector Pin No. 15) BT_ACTIVE J8.16 16) VRF28 (DO NOT USE) J8.17 17) Gnd J8.18,19&20 3.3: SD Memory Interface S. No. Signal Names Connector Pin No. 1)8 CS J9.1 2)8 DI J9.2 3)8 Supply J9.3 4) SCLK J9.4 5)8 GND J9.5 6)8 DO J9.6 7)8 CD J9.6 4: Compliance Statements: 4.1 FCC Compliance Statements This device complies with Part 15 of the FCC rules.
RS9110-N-11-03 Evaluation Board Us er Gu ide User Guide Ver s i o n Version 1.5 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable Protection against harmful interference in a residential installation.
RS91 911R 0-N-1 S 1-03 Evaluation Board Us er Gu ide User Guide Ver sion 1.5 Version 4.2 IC Compliance Statements: This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the Following two conditions :( 1) this device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
