Installation Instructions

DRAFT
basicDIM Wireless Sensor 5DP 38RC (US) INSTALLATION
article number/Artikelnummer: 28002800 / 28002801
10/18-xxx-0 We reserve the right to make technical changes without prior notice.
Tridonic GmbH & Co KG, www.tridonic.com, [e-mail], Tel. [phone]
 mm
 –  mm² (AWG  – )
Wiring diagram
solid or stranded
ein- oder mehrdrähtig
monobrin
a filo unico
monofilar
entrådig
220–240 V
L
N
50 Hz
68
56
68,2
73,3
68
78.5
100
ø85
56
68.2
73,3
ø19.2
L
N
Dimensions US versions (28002800)
Dimensions EU versions (28002801)
EU US RC
basicDIM Wireless Sensor provides movement detection and lux control wire-
less to other basicDIM Wireless devices to achieve smart control as presence
detection, daylight harvesting.
Technical Data
Rated supply voltage 220 – 240 V
Rated supply voltage (US version) 120 – 277 V
Mains frequency 50 / 60 Hz
Detection range, mounted at height of 3 m ø6 m
Detection angle tbd°
Light measurement at sensor head 1 – 2,000 lx (± 20 %)
Radio transceiver operating frequencies 2.4 – 2.483 GHz
Max. output power radio transceiver + 4 dBM
Operating temperature 0 ... +50 °C
tc point 70 °C
Storage temperature -40 ... +85 °C
Dimensions for integrated mounting ø65 mm
Type of protection IP20
Installation Instructions
Make sure that the mains voltage is switched off when making any connections.
Use 0.75 – 2.5 mm² (AWG 20 – 14) solid or stranded conductor electrical wires.
Strip the wire 8 mm from the end.
Insert the wires to the corresponding holes and tighten the connector screw.
Mains input connector is marked with letters L and N.
When installed at a height other than the recommended installation height
(3 m), the presence sensor might show different characteristics. When mounted
at a higher level, its sensitivity is reduced. If mounted at a lower level, its range is
diminished.
Heaters, fans, printers and copiers located in the detection zone may cause
incorrect presence detection.
Optimal positioning of the sensor
The sensor must be positioned on the ceiling so that the hands of the person
using the room are in the centre of the detection zone without being covered by a
screen, bodies and so on.
Compatible devices
Compatible with all Android 4.4 (KitKat) or later, iPhone 4S (iOS 5.0) or later and
iPAD 3 (iOS 5.1) or later.
Hereby, Tridonic declares that the radio equipment type basicDIM Wireless
(28002212) is in compliance with Directive 2014/53/EU.
The full text is available at the following internet address:
http://www.tridonic.com/PDB/resources/TRCertPDF/42395_TA%20602_00.pdf
Safety instructions
• Installation of this device may only be carried out by specialist staff who have
provided proof of their skills.
• The power supply must be switched off before handling the device.
• The relevant safety and accident prevention regulations must be observed.
Areas of application
The device may only
• be used for the applications specified.
• for safe installation in dry, clean environment.
• be installed in such a way that access is only possible using a tool.
UK
Installationshinweise
Achten Sie darauf, dass die Netzspannung abgeschaltet ist, wenn Sie
Verbindungen herstellen. Verwenden Sie eindrähtige- oder mehrdrähtige Kabel mit
einem Querschnitt von 0,75–1,5 mm². Isolieren Sie am Kabelende 6–7 mm ab.
Drücken sie den Klemmendrücker nach unten und stecken Sie die Kabel in die
dafür vorgesehenen Öffnungen.
Das basicDIM Wireless Passive Module wird über den DALI Bus versorgt.
Um die Funktion sicher zu stellen, ist es notwendig den DALI Bus extern zu ver-
sorgen. Es verfügt über zwei Paar Klemmen.
Die Paare sind intern, parallel verbunden.
Dadurch kann eine Durchgangsverdrahtung einfach realisiert werden.
Die Anschlüsse sind mit „DA1“ und DA2“ gekennzeichnet.
Kompatible Geräte
Kompatibel mit Android 4.4 (KitKat) oder höher, iPhone 4S (iOS 5.0) oder höher
und iPAD 3 (iOS 5.1) oder höher.
Hiermit erklärt Tridonic, dass der Funkanlagentyp basicDIM Wireless Passive
Module (28002574) der Richtlinie 2014/53/EU entspricht.
Der vollständige Text ist unter der folgenden Internetadresse verfügbar:
http://www.tridonic.com/PDB/resources/TRCertPDF/42395_TA%20602_00.pdf
Einsatzbereich
Das Gerät
• darf nur für den bestimmungsgemäßen Einsatz verwendet werden.
• muss für eine sichere Installation in einer trockenen, sauberen Umgebung
installiert werden.
• muss so installiert werden, dass der Zugang nur mit einem Werkzeug möglich
ist.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates,uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
FCC RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or transmitter.