TRENDnet User’s Guide Contents Product Overview ............................................................................ 3 Features ...................................................................................................................3 Specifications ...........................................................................................................3 Package Contents ....................................................................................................4 Front View ....
TRENDnet User’s Guide Product Overview TV‐IP344PI Specifications 4 Megapixel Record up to 4MP HD video (2560 x 1440) at 20 fps in the space saving H.265 compression format Varifocal Lens Varifocal surveillance camera has built‐in 2.8 – 12mm motorized varifocal lens, allowing you to adjust the field of view to meet your installation needs Covert Night Vision Masked IR LEDs provide covert night‐time viewing up to 30m (98 ft.) away Features TRENDnet’s Indoor/Outdoor 4MP H.
TRENDnet User’s Guide 3‐Axis Mounting Base Integrated 3‐axis mounting base provides installation flexibility Advanced Playback TV‐IP344PI Complimentary Apps Live video to a mobile device with free iOS® and Android™ apps Package Contents Advanced in‐camera archived video playback functionality TV‐IP344PI package includes: Motion Detection Create custom motion detection zones for the varifocal surveillance camera to record video and send email notifications when a zone is triggered TV‐IP344PI Wea
TRENDnet User’s Guide TV‐IP344PI Front View Warnings Serious injury or death may be caused if any of these warnings are neglected. Follow these safety guards to prevent serious injury or death. • If using the power adapter, please choose the power adapter that meets the safety extra low voltage (SELV) standard or IEC60950‐1 and Limited Power Source standard. • If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself.
TRENDnet User’s Guide Cautions Injury or equipment damage may be caused if any of these cautions are neglected. Follow these precautions to prevent potential injury or material damage. • Make sure the power supply voltage is correct before using the Camera. • Do not drop the camera or subject to physical shock. • Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.
TRENDnet User’s Guide TV‐IP344PI • Sunlight: Avoid direct sun light exposure. Direct sun light will damage the image sensor. If sunlight is necessary for your viewing purposes, provide protection for the image sensor. • Lighting: Consider installing your camera faces the same direction of the light sources. Shooting images with top‐down position outdoor or next to the existing light source are good choices. Avoid the light source if it creates a shade that darkens the viewing area.
TRENDnet User’s Guide Hardware Installation Cabling It’s recommended that the wiring the cable in your home or office by a professional. If you already have the cable deployed, make sure the cable and the connectors meet the category 5 Ethernet cable standards. At least 2 pairs of twisted lines are required for power and data. Poor cable quality may cause unexpected problems. Testing your cable or running a new cable is suggested for new camera installation.
TRENDnet User’s Guide 4. This will also require you to Install WinPcap program if you don’t have this installed before, please follow the on screen Instructions to Install It. TV‐IP344PI 6. After the computer has restarted, double click on the Camera Utility icon to launch the program. 7. Find the camera you would like to access and configure then double click on the IP address. 5. Restart the computer after the Installation. 8.
TRENDnet User’s Guide Access your Camera with the Web Browser Logging‐in to the Camera for the First Time (Windows) TV‐IP344PI 3. The camera management page will detect if you installed the camera video streaming plug‐in or not. Click the link to download the plug‐in from the camera. (For Internet Explorer and Safari only) Google and Firefox users, skip to step 9. 1. Find the camera from the Utility and double click on the IP address to open the browser. 2.
TRENDnet User’s Guide 5. Permission request may show up depends on the Internet security settings on your computer. Click Yes or Run anyway to install the plug‐ in. 6. Click Next to install the plug‐in. © Copyright 2019 TRENDnet. All Rights Reserved. TV‐IP344PI 7. Click Finish to finish the installation. 8. Open the browser and login again, enter the user name admin and new password again to start secured session.
TRENDnet User’s Guide 9. Refresh the browser and the Live View page will show up and begin streaming video. TV‐IP344PI Logging‐in to the Camera for the First Time (OS X) 1. Open the web browser on your computer. In the address bar, enter the default IP address of the camera 192.168.10.30. If the camera is connected to a router/network, please use the Windows Camera Utility to find the exact IP address. 2. Activate the admin User Account by entering your desired password, and then click OK.
TRENDnet User’s Guide 3. The camera management page will detect if you installed the camera webcomponent plug‐in or not. Click the link to download the plug‐in from the camera. Note: Internet connection is required to download the plug‐in. If you do not have Internet access, you can find the plug‐in on the CD comes with the package under /Mac folder. TV‐IP344PI 5. Go to the Finder and navigate to the Download folder. Command‐Click the WebComponents.pkg and then click Open.
TRENDnet User’s Guide 7. Click Continue to install the plug‐in. TV‐IP344PI 9. Use the default location and click Install. 10. Enter your password and click Install Software 8. Select a destination to install the plug‐in. Then click Continue. © Copyright 2019 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide 11. Installation will process automatically. TV‐IP344PI Live View After you log‐in into the camera management page, you’ll see the Live View page. 12. Click Close to exit the installation. © Copyright 2019 TRENDnet. All Rights Reserved. Video Stream The camera has two video streams: H.264 and MJPEG.
TRENDnet User’s Guide TV‐IP344PI will indicate if it is in recording state or not Zoom Regional Exposure Click once to enable zoom. Then, click and drag the area on the picture to zoom in. Click once on picture for 100% zoom. Click the icon again to disable zoom. The zoom function works in full screen mode as well Playback You can playback the video recording on the network storage and download the video clip and snapshots to your local computer.
TRENDnet User’s Guide TV‐IP344PI Time Line There is a play back head in the center of the time line represented in a yellow vertical line. To look for a specific video recording, move the time line by clicking and dragging it. If the recording is short, zoom in by clicking button. Click to zoom out the time scale. If you know the exact time of the day you are looking for, click Playback Use playback controls to play back the video recording. then enter the time you want to playback.
TRENDnet User’s Guide Slice images from video playback You can take snapshots from playback video or make new video clips from the video you are playing back. TV‐IP344PI Picture Click button to list snapshots to download Click this button to start/stop all recordings. Click this button to take a snapshot of current playback. Click this button to clip a video from playback. Click this button to enable zoom. Then click and drag on the video to define the area you want to zoom in.
TRENDnet User’s Guide TV‐IP344PI Configuration System System Settings Basic Information Setup your camera name and location for easy identification. This camera name will also be recognized by other network camera software as the name of this camera. OSD, On Screen Display, camera name is referring to this setting as well. Location: Device Number Model Serial No. Firmware Version software and OSD, On Screen Display.
TRENDnet User’s Guide Time Settings The accuracy of the system clock is important for scheduling and accurate logging. You can synchronize the system time with your computer, or automatically check the time accuracy with a network time server (NTP server). Automatic Update NTP Specify a time server (NTP server) to synchronize with. Server: (e.g. pool.ntp.org) Interval: The time interval that the TV‐IP344PI will synchronize the time with NTP server.
TRENDnet User’s Guide Maintenance Upgrade and Maintenance You can restart, load camera settings and upgrade the camera firmware on this page. TV‐IP344PI Status: Shows the status in loading configuration file. Export Config. File Export: Click Export to download configuration file. The file will be downloaded to the Download folder by default. Remote Upgrade Firmware: Click Browse to find the latest firmware and then click Upgrade. Status: Shows the status in firmware upgrade.
TRENDnet User’s Guide TV‐IP344PI Log System Service The log of the camera will be saved on the network storage. You can search the relevant records and save to your local computer. This section allows you to enable/disable IR light control. Search for logs Click the type of log and then the Start Time and End Time. Click Search to start searching. Click First Page , Prev Page , Next Page , and Last Page show the logs. Click Save Log to save the logs to your computer. © Copyright 2019 TRENDnet.
TRENDnet User’s Guide TV‐IP344PI IP Address Filter Security Authentication Configure the parameters, including Authentication, Anonymous Visit, IP 1. Enter the IP Address Filter interface: Configuration > System > Security > IP Address Filter Address Filter, and Security Service from security interface. 1. Enter the Authentication interface: Configuration > System > Security > Authentication. 2. Check the checkbox of Enable IP Address Filter. 3.
TRENDnet User’s Guide Modify an IP Address TV‐IP344PI Security Services Steps: (1) Left‐click an IP address from filter list and click Modify. To enable the remote login, and improve the data communication security, (2) Modify the IP address in the text filed. the camera provides the security service for better user experience. Steps: 1. Enter the security service configuration interface: Configuration > System > Security > Security Service. (3) Click the OK to finish modifying.
TRENDnet User’s Guide TV‐IP344PI User Management Online Users User Management You can setup up to 16 user accounts to access the camera’s video stream with a web browser or real time video stream (RTSP). Only one administrator account can be setup to configure the TV‐IP344PI and cannot be deleted. You can see the current users who are visiting the device through this interface. User information, such as user name, level, IP address, and operation time, is displayed in the User List.
TRENDnet User’s Guide TV‐IP344PI Network Basic Settings 1. Configure the basic network settings, including the NIC Type, IPv4 or IPv6 You can configure the parameters, including TCP/IP, DDNS, PPPoE, Port, and Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU NAT, etc., by following the instructions in this section. TCP/IP Setup your basic IPv4 and IPv6 network settings on this page. settings and Multicast Address. 2.
TRENDnet User’s Guide TV‐IP344PI DDNS If your camera is set to use PPPoE as its default network connection, you can use the Dynamic DNS (DDNS) for network access. Before you start: Registration on the DDNS server is required before configuring the DDNS settings of the camera. Steps: 1. Check the Enable DDNS checkbox to enable this feature. 2. Select DDNS Type. Two DDNS types are selectable: DynDNS and NO‐IP. DynDNS or NO‐IP: Steps: (1) Enter Server Address of DynDNS or NO‐IP (e.g. members.dyndns.
TRENDnet User’s Guide PPPoE TV‐IP344PI 3. Click Save to save and exit the interface. Note: A reboot is required for the settings to take effect. Port You can change the service port numbers of TV‐IP344PI and enable/disable RTSP or HTTPS services. 1. Check the Enable PPPoE checkbox to enable this feature. 2. Enter User Name, Password, and Confirm password for PPPoE access. Note: The User Name and Password should be assigned by your ISP.
TRENDnet User’s Guide TV‐IP344PI Server Port: The default server port number is 8000, and it can be With the function enabled, you don’t need to configure the port mapping for changed to any port No. ranges from 2000 to 65535. each port, and the camera is connected to the Wide Area Network via the Note: router. When you use client software to visit the camera and you have changed the server port number, you have to input the correct server port number in login interface to access to the camera.
TRENDnet User’s Guide 4. TV‐IP344PI Select the port mapping mode. Manual and Auto are selectable. security and SNMP v2 requires password for access. And SNMP v3 Note: provides encryption and if you use the third version, HTTPS protocol must be enabled. If you select Auto, you should enable UPnP™ function on the router. 5. If you select Manual, you can customize the value of the external port 1. and complete port mapping settings on router manually. SNMPv3 to enable the feature correspondingly.
TRENDnet User’s Guide TV‐IP344PI FTP You can configure the FTP server related information to enable the uploading of the captured pictures to the FTP server. The captured pictures can be triggered by events or a timing snapshot task. 1. Input the FTP address and port. 2. Configure the FTP settings; and the user name and password are required for the FTP server login. © Copyright 2019 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide risks, we strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers and special characters) in order to increase the TV‐IP344PI (e.g., 10.11.37.189_01_20150917094425492_FACE_DETECTION.jpg). Or you can customize it by adding a Custom Prefix to the default naming rule.
TRENDnet User’s Guide Email TV‐IP344PI 1. Configure the following settings: Sender: The name of the email sender. Sender’s Address: The email address of the sender. SMTP Server: IP address or host name (e.g., smtp.263xmail.com) of the SMTP Server. SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25 (not secured). And the SSL SMTP port is 465. Email Encryption: None, SSL, and TLS are selectable.
TRENDnet User’s Guide Authentication (optional): If your email server requires authentication, TV‐IP344PI check this checkbox to use authentication to log in to this server and HTTPS HTTPS provides authentication of the web site and its associated web server, input the login user name and password. which protects against Man‐in‐the‐middle attacks. Perform the following steps to set the port number of https.
TRENDnet User’s Guide Create the authorized certificate (1) Select Create the certificate request first and continue the installation as the Installation Method. (2) Click Create button to create the certificate request. Fill in the required information in the popup window. (3) Download the certificate request and submit it to the trusted certificate authority for signature. (4) After receiving the signed valid certificate, import the certificate to the device. TV‐IP344PI 1.
TRENDnet User’s Guide Before you start: The authentication server must be configured. Please apply and register a user name and password for 802.1X in the server. TV‐IP344PI Integration Protocol If you need to access to the device through ONVIF protocol, you can configure ONVIF user in this interface. Refer to ONVIF standard for detailed configuration rules.
TRENDnet User’s Guide Video/Audio Follow the instructions below to configure the video setting, audio settings, ROI, Display info. on Stream, etc. TV‐IP344PI bandwidth, and the sub‐stream can be used for live view when the bandwidth is limited. 2. You can customize the following parameters for the selected stream type. Video Video Type: Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio.
TRENDnet User’s Guide TV‐IP344PI Note: The maximum limit of the max. bitrate value varies according to storage by up to 50% with the same maximum bitrate in most scenes. different camera platforms. For certain cameras, the maximum limit is You need to reboot the camera if you want to turn on or turn off the 8192 Kbps or 12288 Kbps. H.264+/H.265+. If you switch from H.264+ to H.265+ directly, and vice Video Encoding: versa, a reboot is not required by the system.
TRENDnet User’s Guide I Frame Interval: TV‐IP344PI Set I Frame Interval from 1 to 400. ROI ROI (Region of Interest) encoding helps to discriminate the ROI and SVC: background information in video compression, which means, the technology Scalable Video Coding is an extension of the H.264/AVC and H.265 assigns more encoding resource to the region of interest, thus to increase the standard. Select OFF/ON to disable/enable the SVC function.
TRENDnet User’s Guide 1. Select the Stream Type for ROI encoding. 2. Check the checkbox of Enable under Fixed Region item. 3. Set Fixed Region for ROI. (1) Select the Region No. from the drop‐down list. TV‐IP344PI Image Display Settings Adjust video image quality, lightness, and color settings here. (2) Check the Enable checkbox to enable ROI function for the chosen region. (3) Click Drawing. Click and drag the mouse on the view screen to draw a red rectangle as the ROI region.
TRENDnet User’s Guide Exposure Settings time refers to the interval time between the day/night switch. You can If the camera is equipped with the fixed lens, only Manual is selectable, set it from 5s to 120s. and the iris mode is not configurable. TV‐IP344PI Backlight Settings The Exposure Time refers to the electronic shutter time, which ranges BLC Area: If you focus on an object against strong backlight, the object from 1 to 1/100,000s.
TRENDnet User’s Guide Video Adjustment TV‐IP344PI On Screen Display Settings Mirror: It mirrors the image so you can see it inversed. Left/Right, Up/Down, Center, and OFF are selectable. Display the camera name and the time the video is shooting on the screen Video Standard: 50 Hz and 60 Hz are selectable. Choose according to the different video standards; normally 50 Hz for PAL standard and 60 Hz for NTSC standard. Capture Mode: Set the capture resolution at a fixed value. 1.
TRENDnet User’s Guide (2) Input the characters in the textbox. TV‐IP344PI Privacy Mask Note: Up to 8 text overlays are configurable. 6. Adjust the position and alignment of text frames. Display extra information on the screen over the image. Left align, right align and custom are selectable. If you select custom, you can use the mouse to click and drag text frames in the live view window to adjust their positions. Note: The alignment adjustment is only applicable to Text Overlay items. 7.
TRENDnet User’s Guide Events Motion Detection Set up how the motion detection event will be triggered and what actions will be triggered. TV‐IP344PI 1. Check the checkbox of Enable Motion Detection. 2. Check the checkbox of Enable Dynamic Analysis for Motion if you want to mark the detected objects with green rectangles. 3. Click Draw Area. Click and drag the mouse on the live video to draw a motion detection area. Click Stop Drawing to finish drawing one area. 4.
TRENDnet User’s Guide TV‐IP344PI Channel and Trigger Alarm Output are selectable. You can specify the linkage method when an event occurs. Note: The linkage methods vary according to the different camera models. Send Email Send an email with alarm information to a user or users when an event occurs. Upload to FTP/Memory Card/NAS Capture the image when an alarm is triggered and upload the picture to Note: Click on the selected time period, you can adjust the time period a FTP server.
TRENDnet User’s Guide TV‐IP344PI Storage Record Schedule There are two kinds of recording for the cameras: manual recording and scheduled recording. In this section, you can follow the instructions to configure the scheduled recording. By default, the record files of scheduled recording are stored in the local storage or in the network disk. Pre‐record: The time you set to start recording before the scheduled time or the event.
TRENDnet User’s Guide TV‐IP344PI 3. Select a Record Type. The record type can be Continuous, Motion Besides configuring the recording schedule, you have to configure Detection, Alarm, Motion | Alarm, Motion & Alarm, and Event. the settings on the Motion Detection and Alarm Input Settings interfaces. Continuous If you select Continuous, the video will be recorded automatically according to the time of the schedule.
TRENDnet User’s Guide TV‐IP344PI Capture You can configure the scheduled snapshot and event‐triggered snapshot. The captured picture can be stored in the local storage or network storage. 3. Click Save to save the settings. 4. Go to Capture Parameters tab to configure the capture parameters. (1) Check the Enable Timing Snapshot checkbox to enable continuous snapshot. (2) Select the picture format, resolution, quality and capture interval.
TRENDnet User’s Guide TV‐IP344PI Regulations Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TRENDnet User’s Guide TV‐IP344PI Europe – EU Declaration of Conformity Français [French] This device complies with the essential requirements of the Directive 2004/108/EC and 2006/95/EC.
TRENDnet User’s Guide TV‐IP344PI Limited Warranty TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET’S PRODUCTS. TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.