Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Copyright 2005 Version 1.0 (July, 2005) Disclaimer The information in this document is subject to change without notice.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This hastested been tested for notebook lap-held configuration and occur complies with FCC Thisequipment device was for typical by stander conditions that may during use.
Table of Contents Getting Started with the TEW-601PC .......................................................... 1 Overview of the Wireless Client Utility .......................................................................... 2 Working with Profiles .................................................................................................... 3 Creating a Profile ....................................................................................................................
Appendix ............................................................................................................31 Maintenance ................................................................................................................31 Checking the Wireless Client Utility Version ........................................................................ 32 Uninstalling the Wireless Client Utility .................................................................................
Getting Started with the TEW-601PC Congratulations on purchasing the TEW-601PC! The quick start guide included with your TEW-601PC tells you how to install the Wireless Client Utility and how to operate the Wireless feature of the TEW-601PC. This manual provides information for setting up and configuring the TEW-601PC. This manual is intended for both home users and professionals. It is not required to read some of the more technical information in this manual to operate and enjoy the TEW-601PC.
Overview of the Wireless Client Utility The Wireless Client Utility is included on the CD that shipped with the TEW-601PC. Install the utility as described in the Quick Start Guide before attaching the TEW-601PC to your computer. IMPORTANT BE SURE TO INSTALL THE WIRELESS CLIENT UTILITY BEFORE YOU ATTACH THE TEW-601PC TO YOUR COMPUTER. ATTACHING THE TEW-601PC BEFORE THE UTILITY IS INSTALLED COULD CAUSE THE INSTALLATION TO FAIL.
The Link Information pane provides information on your current connection. This same pane is shows at the bottom of all screens so you are always aware of your connection status. l NOTE WHEN THE WCB-360A IS NOT CONNECTED TO YOUR COMPUTER, MOST SETTINGS IN THE WIRELESS CLIENT UTILITY ARE UNAVAILABLE. SETTINGS OR BUTTONS THAT ARE NOT AVAILABLE ARE GRAYED OUT. Working with Profiles A profile is a record of the configuration you use to connect to a particular access point.
2. Click Add. The Wireless Client Utility Profile Wizard opens. 3. Type a descriptive name for the profile such as Home or Test. 4. Click the drop-down arrow at Network Mode and select Infrastructure or Ad-Hoc. Choose Infrastructure when connecting to an access point or wireless router. You will need to know the SSID of the access point. Choose Ad-Hoc when connecting directly to another computer without using an access point.
5. In the SSID pane click Browse. The utility performs a site survey and displays the results. The SSID (Service Set IDentifier) is the name assigned to a wireless Wi-Fi network. All devices must use this case-sensitive name, which is a text string up to 32 bytes long, in order to communicate. 6. Select the SSID you want to connect to and click Add To Profile. 7. Click Next. The WLAN Security Configuration screen appears.
8. 9. Select the Security Mode from the drop-down list and then select the appropriate settings for the security mode. Click Next to select Wireless Protocol 10. Click Save to complete the wizard and save the new profile. (If you do not want to activate the profile, uncheck the Apply this profile now checkbox.
MODIFYING PROFILES You may need to modify settings for a profile, for example, if you purchase a new router, or if your office administrator provides you with new security settings. Refer to the following to modify a profile. 1. Open the Wireless Client Utility and click Profile. 2. Select the profile you want to modify and click Properties.
3. Make the changes you want to the Basic Settings and click Advanced Settings. Unless you have a thorough understanding of wireless networking, it is recommended that you leave these settings at the defaults. 4. Click WLAN Security. (Refer to “Configuring Wireless Security” for more details on security settings.
WPA/WPA2 WPA encrypts all traffic between the access point and the client using either TKIP or AES encryption. Depending on the authentication protocol selected, each client must authenticate using their own unique username, password, and security certificate. WPA-PSK/WPA2-PSK WPA-PSK or WPA2-PSK is a compromise between WPA/WPA2 and WEP. Like WEP, it uses a pre-shared key that every user of the network must have in order to send and receive data. Like WPA, it uses either TKIP or AES.
Checking for Available Access Points The number of access points or hot spots for public use is constantly increasing in major cities. Many Web sites report on the locations of hot spots. Check the following Web sites for updated information for your location. • • • • • • http://intel.jiwire.com www.hotspot-locations.com www.hotspotlist.com www.wififreespot.com www.wifinder.com www.wi-fizone.
3. Select the network you want and click Connect. Or click Add To Profile if you want to connect later. For details about any of the listed access points, select it from the list and click Detailed Info to see the following screen. (You can also double-click an access point to view the Detailed Info screen. Disabling the Wireless Client Utility You may need to have Windows manage your wireless network settings. In that case, you should disable the Wireless Client Utility.
Exploring the Wireless Client Utility Screens This section covers the following topics: • • • • • The Network Screen The Profile Screen The SiteSurvey Screen The Options Screen The Version Screen The Network Screen The Wireless Client Utility is included on the CD that shipped with the TEW-601PC. Install the utility as described in the Quick Start Guide before attaching the TEW-601PC to your computer. BE SURE TO INSTALL THE WIRELESS CLIENT UTILITY BEFORE YOU ATTACH THE TEW-601PC TO YOUR COMPUTER.
WIRELESS SETTING The Wireless Setting pane settings are described below Shows the current profile you have selected. If you have not added a profile, only Default shows. The settings shown in the Network screen are for the current profile. Click the dropdown arrow to select another profile. Reconnect (button) Press to reconnect to the current access point. Current Profile Network Mode Security Authentication Shows the current network mode. Infrastructure or ad-hoc mode.
WIRELESS SYSTEMS WORK IN INFRASTRUCTURE MODE OR PEER-TO-PEER MODE. IN INFRASTRUCTURE MODE, WIRELESS DEVICES COMMUNICATE TO A WIRED LAN VIA ACCESS POINTS. IN AD-HOC MODE (ALSO KNOWN AS PEERTO-PEER MODE), WIRELESS DEVICES COMMUNICATE WITH EACH OTHER DIRECTLY AND DO NOT USE AN ACCESS POINT. TCP/IP S ETTING The TCP/IP Setting pane settings are described below. IP Address Shows the current network IP address. Subnet Mask Shows the current subnet mask status. Gateway Shows the current gateway.
THE LINK INFORMATION PANEL IS SHOWN IN ALL SCREENS SO YOU CAN ALWAYS SEE THE STATUS OF YOUR CURRENT CONNECTION. MONITOR THIS SETTING AS YOU MOVE AROUND TO ATTAIN A SUITABLE SIGNAL.. NOTE WIRELESS SYSTEMS WORK IN INFRASTRUCTURE MODE OR AD-HOC (PEER-TO-PEER) MODE. IN INFRASTRUCTURE MODE, WIRELESS DEVICES COMMUNICATE TO A WIRED LAN VIA ACCESS POINTS. EACH ACCESS POINT AND ITS WIRELESS DEVICES ARE KNOWN AS A BASIC SERVICE SET (BSS).
PROFILE LIST The Profile List pane settings are described below. Name Shows the name of the profile that you assigned. If only default displays, no profiles have been added. SSID IP Address Shows the name (usually the equipment vendor's name) assigned to a wireless Wi-Fi network. (The keyword “ANY” means any available network.) Shows the IP address. Add (button) Click to add a profile. Remove (button) Click to remove the selected profile.
AVAILABLE NETWORKS The Available Networks pane settings are described below. SSID Shows the name (usually the equipment vendor's name) assigned to a wireless Wi-Fi network. Mode Shows the signal type (802.11b/g). Strength Shows the signal strength. Ch Shows the network channel. Security Shows the security status. Refresh (button) Click to refresh the list of currently available networks. Detailed Info (button) Click to view properties for the selected network. (See Detailed Info. Screen below.
The Options Screen By default, the Wireless Client Utility configures your wireless settings. Use this screen to disable the Wireless Client Utility. OPTIONS The Options pane settings are described below. Let Windows manage this wireless adapter (tick box) When you check the Let Windows manage this wireless adapter checkbox, Windows Zero Configuration manages your wireless settings. The Wireless Client Utility still shows the link status of the adapter. Apply Now (button) Click to execute the changes.
The Version Screen This screen displays the software and hardware information of the adapter. You cannot make changes to this screen. Reference the Version screen if you need to contact technical support. See “Maintenance”.
Configuring Wireless Security This chapter covers the configuration of security options in the 802.11 Wireless Client Utility. Configuring Security When you create a profile you need to configure the security settings with the information provided by the administrator. You modify security settings by selecting the profile and clicking Properties.
C ONFIGURING W E P Refer to the following to modify WEP settings. 1. In the Properties window, click WLAN Security. 2. Click the drop-down arrow at Security Mode and choose WEP. 3. Click the Use Static WEP checkbox.
4. Click Configure. The WEP Configuration screen appears. WEP Method Select the encryption to match your access point: 64, 128, or 152-bit. The encryption level must match the encryption level used by your access point. Authentication Options are Auto, Open System, and Shared. For most installations choose Auto. Make Key using PassPhrase A WEP Key is automatically generated as you type in any Passphrase of your choice.
C ONFIGURING WPA & WPA2 Refer to the following to configure WPA & WPA2. 1. Click the drop-down arrow at Security Mode and choose WPA / WPA2. 2. Click the drop-down arrow at Encryption Method and choose TKIP or AES. To configure 802.1X (authentication protocol) for WPA/ WPA2, see “Configuring 802.1X ” section.
C ONFIGURING WPA-PSK & WPA2-PSK Refer to the following to configure WPA-PSK & WPA2-PSK. Click the drop-down arrow at Security Mode and choose WPA-PSK / WPA2-PSK. 1. 2. Click the drop-down arrow at Encryption Method and choose TKIP or AES. (Most access points use TKIP for WPA-PSK & AES for WPA2-PSK.) At PSK Passphrase enter the same pass phrase used to configure the WPA-PSK or WPA2-PSK on your access point.
C ONFIGURING 802.1X You need to know if your access point supports 802.1X and then apply the configuration here. 1. Choose the EAP method under Authentication protocol. 2. Options for User Information depend on the EAP method chosen. C ONFIGURING 802.1X – PEAP Refer to the following to configure PEAP. 1. 2. 3. 4. 5. At WPA/ WPA2 security mode, click Configure button next to Authentication Protocol. Select Inner PEAP protocol. Click Save to finish and return to the previous screen.
Use user certificate Check this box if your network requires user certification and then select the certificate from the drop-down menu. Validate server certificate Check this box if your network requires server certification and then select the certificate authority from the drop-down menu. Server name: Type in the name of the server that is used for 802.1X authentication. Server name should match exactly Check this box if the server name should exactly match the name in the certificate. 6.
C ONFIGURING 802.1X – EAP-TLS 1. At Security Mode select WPA/ WPA2 from the drop-down menu. 2. At Authentication Protocol select TLS from the drop-down menu. 3. TLS requires both server and user certification. Click Configure Certificate (see Note below).
Use user certificate Check this box if your network requires user certification and then select the certificate from the drop-down menu. Validate server certificate Check this box if your network requires server certification and then select the certificate authority from the drop-down menu. Server name: Type in the name of the server that is used for 802.1X authentication. Server name should match Check this box if the server name should exactly match the name exactly in the certificate. 5.
Glossary For unfamiliar terms used below, look for entries elsewhere in the glossary. A D-H OC Ad-hoc mode does not require an AP or a wired network. A network that transmits wireless from computer to computer without the use of a base station (access point). Two or more wireless stations communicate directly to each other. An ad-hoc network may sometimes be referred to as an Independent Basic Service Set (IBSS). C HANNEL A radio frequency used by a wireless device is called a channel.
SSID The SSID (Service Set Identity) is a unique name shared among all wireless devices in a wireless network. Wireless devices must have the same SSID to communicate with each other. T EM POR AL K E Y I N TE G RI TY P R O TO C O L (TKIP) Temporal Key Integrity Protocol (TKIP) uses 128-bit keys that are dynamically generated and distributed by the authentication server. U S E R A U T H E N T I C AT I O N WPA applies IEEE 802.
Appendix This section provides maintenance and troubleshooting procedures. The following topics are discussed: • • See “Maintenance” See “Troubleshooting” Maintenance Installing a newer version of the Wireless Client Utility may improve the performance of the TEW-601PC. Before installing the new version, you must uninstall the old one. CHECKING THE WIRELESS CLIENT UTILITY VERSION To check the current Wireless Client Utility, open the utility on the Version screen.
UNINSTALLING THE WIRELESS CLIENT UTILITY Refer to the following to uninstall (remove) the Wireless Client Utility from your computer. 1. Click Start -> All Programs (Windows 2000 Programs) -> 802.11g Wireless Client Utility -> Uninstall. 2. 3. When prompted, click Yes to remove the driver and utility software. 4. 5. Click Finish to complete the uninstallation. Reboot your computer if prompted.
Troubleshooting P ROBLEMS S TARTING THE 802.11g W IRELESS C LIENT U TILITY P ROGRAM PROBLEM Windows does not auto-detect the TEW-601PC. CORRECTIVE ACTION Make sure the TEW-601PC power switch is turned off and properly inserted into the PCMCIA slot and then restart your computer. Perform a hardware scan by clicking Start, Settings, Control Panel and then double-click Add/Remove Hardware. (Steps may vary depending on Windows version).
Infrastructure Make sure that the AP and the associated computers are turned on and working properly. Make sure the TEW-601PC computer and the associated AP use the same SSID. Change the AP and the associated wireless clients to use another radio channel if interference is high. Make sure that the computer and the AP share the same security option and key. Verify the settings in the Profile Security Settings screen. Ad-Hoc Verify that the peer computer(s) is turned on.
Limited Warranty TRENDware warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDWARE ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF