User's Manual

2
Less than 50cm
1
Step1: Battery On
1. Remove the back cover.
2. Install two AAA batteries.
Step2: Sensor Pairing
1. Turn on camera and launch “iSmart-CAM” APP. Go to “Camera Setting”
and tap ”IoT Sensor Setting”.
2. Tap the then hold the pairing button for 3 seconds
within 5 seconds.
3. The sensor type will be displayed after paring completed.
4. Tap the “Door/Window Sensor” for detailed settings.
Note: If pairing successfully, the LED will light up for 3 seconds.
If failed, the LED will blink.
1
EN
Pairing Button
2. LED Light
3. Magnetic Reed Switch
1.
1
2
3
Product Layout
1
Quick Setup
2
RF_DWM
RF_Door/ Window Sensor
Installation Guide
Manuel de l'utilisateur
Guía de instalación
Installationsanleitung
Guida all'installazione
1
Placement
4
1
- Modulation: GFSK
- Dimensions: 66x34x25mm, Magnet: 58x13x15mm
- Weight: 32.5 g
- Magnet Sensor Gap Activated: 10mm
- Operating Distance: 30m* (indoor)
- Power Supply: 3V (AAAx2)
- Battery Life: 1 year* (Triggered twenty times a day)
- Operating Temperature: 0℃ ~ 40℃ (32℉ ~ 104℉)
*Actual operating distance and battery life may vary with the usage
patterns and operating environment.
- Frequency: 2.4G Hz
RF
Specification
5
1 cm (max)
3
410-000089-00
1
2. Name : Sensor Name
3. : Search this sensor. If searched, the sensor LED will flash five times.
4. Alarm On/Off : “Alarm On ”will enable you to receive push message when
Door/Window sensor event is triggered.
5. : The camera will rotate to a preset position when “Alarm On” and
Door/Window sensor event is triggered. Through live view window to position
the camera and tap “Locate” to confirm.
1. No. : Sensor Number. Tap it to select other sensor. (No. 0,1,2….)
Sensor Setting
3
1
2
4
3
5
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution
To comply with FCC RF exposure compliance requirements, a separation
distance of at least 20 cm must be maintained between the antenna of this
device and all persons.
This Transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution
To comply with FCC RF exposure compliance requirements, a separation distance of at least 20
cm must be maintained between the antenna of this device and all persons.
This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.