Contents What You Get ............................................................................................................................................ 1 Product Layout .......................................................................................................................................... 2 Setting Up .................................................................................................................................................. 5 Setting Up-Camera .............
Camera • • • • • • Receiver One Camera One Receiver One Audio/Video Cable (RCA to RCA for NTSC; RCA to Scart for PAL) Two Power Adapters One Quick Installation Guide This User's Manual Note: Two AC adapters with different length cables are included with this product. Use either depending on distance from the wall outlet.
Product Layout Front View of Camera Bottom View of Camera Rear View of Camera 1 10 5 2 11 3 6 4 7 9 8 2
Product Layout 1 2 3 4 5 6 7 8 9 10 11 Infrared LEDs Eight LEDs to provide infrared light for night vision. Lens Focuses image automatically without any adjustment. Lens Body Rotates up to 180 degrees. Microphone 2.4 GHz Audio/Video Antenna (Front ) Transmits audio/video signals. Caution: Antenna does not rotate freely through 360 degrees. (See "Orienting Units for Optimal Performance", on page 13) Channel Selection Switch Select the channel by sliding the slide switch to the channel number you want.
Product Layout Front View of Receiver Rear View of Camera 1 2 4 3 4 5 6 7 8
Product Layout 1 2 3 4 5 Power Indicator LED The LED should be lit when the ON/OFF switch is in the ON position.. 2.4GHz Audio/Video Antenna (Front ) Transmits and receives Audio/Video signals. Caution: Antenna does not rotate freely 360 degrees. (See "Orienting Units for Optimal Performance", on page 13) Channel Selection Dipswitches Select the channel by setting the channel dipswitch to the ON position.
Setting Up Before you make the connection: • Always make sure the unit ON/OFF switch is in the OFF position. • Set the channel switches on the back of the camera and receiver to the same channel. Camera • 6 Receiver If you wish to wall mount the camera, it is recommended that the receiver reception be tested before fixing in place. Have one person hold the camera against the wall in the selected mounting area while another checks reception on the TV.
Setting Up-Camera 1 Power Supply The camera uses either batteries (AA-size) or household AC current. To Load Batteries 1 Open the battery compartment cover in the direction of the arrow. 2 Insert batteries so their plus (+) and minus (-) ends are facing as shown in the illustration. 3 Close the battery compartment cover. Make sure the battery compartment cover is locked securely. Never mix old batteries with new ones. Remove batteries from the camera if you do not plan to use it for a period of time.
Setting Up-Camera 2 Changing the Lens Orientation Place the camera in a convenient location, point the lens towards the observation area and adjust the angle by rotating the lens body. The camera's auto focus feature automatically focuses the image. The camera's head rotates horizontally up to 200 degrees and vertically up to 30 degrees. The lens is built into a lens body that is designed to rotate vertically up to 180 degrees, allowing the camera to cover the widest angles.
Setting Up-Receiver 1 Connecting the Receiver to a TV 1 Connect one set of audio/video cables to the audio/video jacks of the receiver, matching the plug colors with the jacks on the receiver. 2 Connect the other end of the cable to the audio/video jacks on the TV labeled LINE IN, matching the plug colors with the jacks on the TV. Some connection scenarios are shown on the next page. Note: For PAL systems, the connector on the audio/video component is a Scart socket.
Setting Up-Receiver Connecting to a TV With an Audio/Video Component TV Receiver VIDEO AUDIO IN Connecting to a TV Without Audio/Video IN Jacks If your TV has UHF/VHF input only, and there is no audio/video equipment near your TV, you will need to get an RF-Modulator (available at your local electronic store) to convert the RCA jacks to coax. Then select either channel 3 or 4 on your TV to view the video.
Setting Up-Receiver Connecting to a TV With an Audio/Video Component Receiver VIDEO AUDIO Audio/Video Component 2 VHF/UHF RF OUT TV Power Supply Plug one end of the provided power adapter into a wall outlet and the other end into the rear of the receiver. Turn the ON/OFF switch to the ON position. The LED on the front of the unit should light. 3 Fine Tuning Place the receiver in a convenient location, then adjust its antenna so that the front (curved face) faces the room where the camera is set up.
Setting Up-Other Application Receiving on a Computer • • Connect the yellow video plug of the audio/video cable to the video jack on the TV tuner device or video capture card, and to the video jack of the receiver. Connect the mini stereo plug of the adapter (available in any electronic store) into the AUDIO IN jack on the back of computer, and the red and white audio/video plugs into the AUDIO LEFT and AUDIO RIGHT jacks on the receiver.
Orienting Units for Optimal Performance Placing: Place the camera and receiver on a flat, stable surface to prevent damage from falling. For optimal performance, try to place the units as high as possible to avoid any possible interference from people walking between the camera and the receiver. Microwave ovens can cause interference. Be sure you do not position the camera and receiver with a microwave in the path between them.
Auto-Sequence Function for Multiple Location Monitoring The receiver's built in auto-sequence function is ideal for security use. The receiver can be used with up to four wireless cameras on four different channels and display them in sequence on a single TV/ monitor.
Auto-Sequence Function for Multiple Location Monitoring Note 1: Note 2: The receiver will auto detect the receiving channels, and display them in sequence. When only one channel dip switch is in the ON position, the receiver will receive the channel continuously, without regard to the position of the 5th dip switch. If more than one dip switch remains on, the auto-sequence function will continue on those channels.
Troubleshooting If you are not getting any signal at all • • • • • • • Check that the receiver is properly connected to the TV which you want to receive the signal Check the power ON/OFF switches on the camera and receiver Check power switches on the TV Make sure power plugs are pushed all the way in. Check all cable connections.
Care and Maintenance • • • • • • • • • • • • • • For best performance, don't touch the antennas unnecessarily Keep all its parts and accessories out of young children's reach Camera performances can be adversely affected by fingerprints or dirt on the lens surface. Avoid touching the lens surface with your fingers. Should the lens become dirty, use a blower to blow off dirt and dust, or a soft, dry cloth to wipe off the lens. Keep dry.
Specifications Receiver Frequency Range Antennas Channel AV mod/demod. method Image Sensor Lens Audio Video Dimensions Weight Operating remperature Camera 2.4~2.4835GHz 300 feet (100 meters) clear line of sight Directional circular-polarized antenna 4 selectable channels FM -1/3” CMOS image sensor -f3.6mm, F2.0 Stereo audio input and output -Composite video input and output -14 x 11 x 2.8 cm (5.5 x 4.3 x 1.1 in) 10 x 9 x 15 (3.9 x 3.5x5.9 in) 200g (7.1 ounces) 300 g (10.
