User's Manual

ManualsBrandsTranwo Technology ManualsElectronics5.8Ghz Cable sender

QUI CK I NSTALL GUI DE

Model:

5.8 GHz Cable Sender

• software, warranty card, and user manuals.

1. Package Content ………………………………

2. Panel Control and Function …...……………………………

3. Setup Guide ………………….……………

4. Orient Transmitter/Receiver for optimal performance…….….

5. Specification……………………………………………………

Check to make sure that all units shown as below are enclosed. If something

missed, please contact your dealer.

1. 5.8GHz Transmitter * 1 2. 5.8GHz Receiver * 1

UHF: 433.92MHz (USA Standard)

3. IR Mouse * 1 / fasten strips * 2 4.IR Remote Controller * 1

Contents

1. Package Content

Summary of content (7 pages)

PAGE 1
Contents • software, warranty card, and user manuals. 1. Package Content ……………………………… 2. Panel Control and Function …...…………………………… 3. Setup Guide QUI CK I NSTALL GUI DE ………………….…………… 4. Orient Transmitter/Receiver for optimal performance…….…. 5. Specification…………………………………………………… Model: 5.8 GHz Cable Sender 1. Package Content Check to make sure that all units shown as below are enclosed. If something missed, please contact your dealer. 1. 5.8GHz Transmitter * 1 2. 5.8GHz Receiver * 1 UHF: 433.
PAGE 2
5. Accessories (1) Power Adapters (120V) * 2 (2) RCA Cable * 2 (3) Co-axial T-plug (4) Co-axial cable 1A – UHF antenna receives remote control signal. 1B – UHF antenna sends remote control signal. 2 – Indicator lights show the channel it configured as. 3 – Channel selection button to find optimal reception, the transmitter and receiver must to be 2. Panel Control and Function 5.8GHz Transmitter Configured as the same channel.
PAGE 3
12A–Audio Jack, Left (white), input from source AV equipment. 3. Setup Guide 12B–Audio Jack, Left (white), output to TV. 3.1 To enjoy a life of wireless video and audio, just connect the transmitter to any A/V source you like and CATV cable, and connect the receiver to a TV, IR Remote Controller monitor or speaker in another location. NOTE: Make sure the ON/OFF switch is in the 「OFF」position before connection MUTE □ Transmitter 1.
PAGE 4
3.2 After setup your transmitter and receiver，the first time to enjoy imaginary line drawn between the two units. Three examples are shown as Fig-1, CATV on Cable Sender，It needs to scan and find the available Fig-2 and Fig-3. Since all homes are different, for optimal reception, additional channels ,please follow procedure below : slight pivots or rotations may be necessary. If the transmitter and receiver are l The first step : turn on your TV set and Switch to AV IN.
PAGE 5
< ±8% D.P. Audio 5. Specification 5.1 Transmitter 5.1.1 General specification Input Voltage DC 9V ± 0.5V Current Consumption < 350mA Antenna Type Patch (34 * 34mm) Operation temperature & humidity 0℃ ~ +50℃ less than Input Level 1.4V peak to peak Impedance 600 ohms Frequency Response 30Hz ~ 12KHz Audio Carrier Frequency（L） 6.0MHz ±25KHz Audio Carrier Frequency（R）6.5MHz ±25KHz Audio Distortion 3% max. THD AM Rejection 40dB min. 85% Storage temperature & humidity -20℃ ~ +70℃ less 5.
PAGE 6
LO. Leakage Image Rejection -50dBm max. 40dB 5.3.4 Video 5.3 Output Level Impedance De-Emphasis D.G. D.P. Video S/N Ratio 1V ±0.15Vp-p Load. 75 ohms NTSC < ±8% < ±8% 38dB min. Audio Output Level Impedance Frequency Response 1Vp-p ±0.2 600 ohms 30Hz ~ 12KHz TV Tuner : OSD ENGE630XD(VP-27S) 5.3.1 Channel (VHF): Band I ch. Band II ch. 2àI (fp=55.25 à 169.25MHz) 7 à EEE (fp=175.25 à 463.25MHz) (UHF): Band III ch.FFF à 69 5.3.2 Receiver System : NTSC 5.3.3 Input System : U/V (fp= 469.
PAGE 7
Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.