Installation Guide

ManualsBrandsTransolid ManualsKitchenDiamond 16-Gauge Stainless Steel 25 in. Single Bowl Drop-In Kitchen Sink Kit with Magnetic Accessories

Tools and Materials You will Need

Eye protection (safety glasses/goggles) strongly

recommended

Ball peen hammer ( 6 oz. )

File

Ear protection strongly recommended Slotted screwdriver

Undermount template supplied by Transolid Tape measure

Undermount clips supplied by Transolid.

(NOTE: these come with the sink and are in a

separate plastic bag. Please make sure they are not

thrown away with the carton.)

Drill and drill bit

Stop block ( for drilling holes of a consistent depth)

Router

3/8” thick plywood sheet for cutting a template 5/8” template guide with straight uted router bit

Two 6-inch bar clamps Rags

Framing square Denatured alcohol

Pencil (not permanent marker) Wood braces

Silicone adhesive sealant (not supplied)

INSTALLATION INSTRUCTIONS

MICRO DUAL MOUNT STAINLESS STEEL SINKS

These instructions are for installing Transolid

Micro Dual Mount stainless steel

sinks. This versatile sink with an thin outside edge can be installed three ways.

Undermount (“U”): installed from below the countertop

Inset (“I”): (Drop-in) installed on the countertop

Flushmount (“F”): the sink and countertop form a continuous system which is perfectly

level and has no obstructive edge to get in the way.

If you are installing another type of sink please refer to instructions specically for those

sinks.

ATTENTION INSTALLER:

Transolid

recommends that sinks and routering of solid surface material should be in-

stalled by a professional installer for best results.

Transolid

is not responsible for sink or countertop if damaged during installation.

Metal edges may be sharp - use caution when handling.

Remember, it is your responsibility to follow all local plumbing and building codes.

Inspect sink for damage prior to beginning installation. Do not install a damaged unit.

The warranty will be voided if these installation instructions are not followed.

Templates are supplied only as a guide. The physical use of the sink will ensure a more

accurate cutout.

The instructions that follow are for installing a Transolid

Micro Dual Mount stainless steel

sink. Be sure to read all instructions completely before beginning installation.

LEGAL DISCLAIMER

All technical data and information provided in this publication is done as a public service to customrs of Transolid

and consumers of our products. All

names, designs, and model numbers of products are trademarks of Transolid

. Prices and specications of Transolid’s products are subject to change

without notice or obligation. Transolid

may also change or discontinue models of its products without notice or obligation. While Transolid

endeavors

to provide you with accurate information and descriptions of its products, accuracy and completeness cannot be guaranteed. Transolid

is not respon-

sible for, nor does it have any liability for any mistakes or typographical errors, including liability for incidental, consequential, or special damages. All

products should be inspected and measured promptly upon delivery and certainly before any improvements or alterations are done in anticipation of

or preparation for installation. Transolid

assumes no liability for the use of such information or for any damages incurred through its use or application.

Nothing contained in this publication is to be construed as contractual or providing any form of warranty or representation on the part of Transolid

TRANSOLID

MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY

OR OF FITNESS FOR A PARTICULAR PURPOSE, AS TO THE INFORMATION CONTAINED HEREIN OR THE PRODUCTS DESCRIBED HEREIN.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS MICRO DUAL MOUNT STAINLESS STEEL SINKS These instructions are for installing Transolid® Micro Dual Mount stainless steel sinks. This versatile sink with an thin outside edge can be installed three ways. Undermount (“U”): installed from below the countertop Inset (“I”): (Drop-in) installed on the countertop Flushmount (“F”): the sink and countertop form a continuous system which is perfectly level and has no obstructive edge to get in the way.
PAGE 2
INSTALLATION INSTRUCTIONS (“U”) UNDERMOUNT STAINLESS STEEL SINKS NOTE: When the sink is installed as an undermount it is to be installed with 1/8” countertop overhang. The template provided with the sink illustrates the appropriate countertop cutout for an undermount installation - do not use this template for top mount installations. Sink installation recommended for professional installers only. 1. Position template on countertop.
PAGE 3
. Attach the undermount clips. From the underside of the sink, place one clamp near the center and tighten by hand enough to hold the sink in place. This applies to all four sides. Fastening remaining clamps in position and hand tighten. Space clamps as equally as possible. Provided hardware will accommodate countertops thicker than 3/4” up to 1-1/2”. NOTE: do not fully tighten one clip at a time. Partially tighten a clip, then partially tighten the clip across from it.
PAGE 4
Suggestions for the Care and Cleaning of Transolid® Stainless Steel Sinks When it comes to maintenance, Transolid® recommends to be consistent in your cleaning. It is better to clean on a more frequent basis and avoid the need for heavy duty cleaning. Make sure your sink is clean and dry when not in use. This is the best method of preventive maintenance. Keep the sink water spot free and shiny by rinsing and towel drying after every use.
PAGE 5
Sugerencias para el cuidado y limpieza de los fregaderos de acero inoxidable Transolid® Cuando se trata de mantenimiento, Transolid® recomienda que sea consistente en su limpieza. Es mejor limpiar sobre una base más frecuente y evitar la necesidad de la limpieza pesada. Asegúrese de que el fregadero esté limpio y seco cuando no esté en uso. Este es el mejor método de mantenimiento preventivo. Mantenga el fregadero libre de manchas de agua y brillante por enjuague y secado con toalla después de cada uso.
PAGE 6
3. Coloque los clips inferiores. Desde la parte inferior del fregadero, coloque una abrazadera cerca del centro y apriétela a mano lo suficiente para sostener el fregadero en su lugar. Esto se aplica a los cuatro lados. Sujete las abrazaderas restantes en posición y apriete a mano. Las abrazaderas espaciales son lo más iguales posible. El hardware suministrado acomodará las encimeras más gruesas que 3/4 de pulgada hasta 1-1 / 2 pulgada. NOTA: no apriete completamente un clip a la vez.
PAGE 7
INSTRUCCIONES DE INSTALACIÓN (“U”) UNDERMOUNT SINKS DE ACERO INOXIDABLE NOTA: El fregadero proporcionado es para instalar debajo de la encimera y se debe instalar con un saliente de 1/8 pulgada del contador. La plantilla provista con el fregadero ilustra el corte apropiado del contador para una instalación debajo de la encimera - no utilice esta plantilla para instalaciones de montaje superior. Instalación de fregadero recomendada sólo para instaladores profesionales. 1.
PAGE 8
INSTRUCCIONES DE INSTALACIÓN SINKS DE ACERO INOXIDABLE DE MONTAJE DUAL DEL MICRO Estas instrucciones son para instalar fregaderos de acero inoxidable Transolid® Micro Dual Mount. Este fregadero versátil con un borde exterior delgado se puede instalar de tres maneras.