Wiring Diagram

ManualsBrandsTransmitter Solutions ManualsElectronicsRemote Controller

WHAT’S INCLUDED

The REIGN XRE-100 Relay Extender is a revolutionary product that

will make any dry contact wireless with no programming or

configuration whatsoever - it literally is a plug and play device.

HOW IT WORKS...

Congratulations on your purchase of the Transmitter Solutions XRE-100 Relay Extender System. It has been

designed with state-of-the-art radio technology to extend relay closures, switches, indicators, sensors, and any

other simple ON/OFF status inputs and outputs through extreme obstruction and interference.

If you ordered your XRE-100s together, they are factory paired. All that is required to get up and running is 12-24

Volts AC/DC power and the DRY input closures you want to extend.

If you would like to survey the range capability before install, simply provide power to both units and press the

PROG/TEST button alternately on each unit. Successful transmission and reception will be indicated on the

transmit and receive LEDs on each unit as described below.

v. . .1

XRE – 100

RELAY EXTENDER

There are two pieces that complete the XRE-100.

The Reign XRE-100 - R

elay Extender kit includes 2- XRE-100 units. These units are interchangeable and can be

paired in the field.

Transmitter Solutions refers to the XRE-100 installed at the peripheral device as the Node and the XRE-100

installed at the primary unit the Hub. This is only important during technical support and the wiring diagram.

R E IGN wire l ess

t e chno l o g y

Summary of content (12 pages)

PAGE 1
XRE–100 R E L AY E X T E N D E R v. . .1 REIGN wireless technology The REIGN XRE-100 Relay Extender is a revolutionary product that will make any dry contact wireless with no programming or configuration whatsoever - it literally is a plug and play device. WHAT’S INCLUDED There are two pieces that complete the XRE-100. The Reign XRE-100 - Relay Extender kit includes 2- XRE-100 units. These units are interchangeable and can be paired in the field.
PAGE 2
CONTENTS: 1. . . . ............ .... ..... ...... ....... .... .......... .. ....... .... .......... . . ....... . .. ........... . .......... .... ........ . .......... ... ........ ...... ...... ... .. . ...... .. .......... ........... .. .......... .......... . .. ......... .... . .... . .......... ... ......... ........... ... ........ ...... ...... ... ........ ..... ..... . ..... .......... ......... .. ........... . ........ ... ........... . ... . ..... .. . . ..... . . ....... .. ..
PAGE 3
1. FCC ID: 2ASPOXRE100A: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
PAGE 4
. . POWER DETAILS Each side of The XRE-100 (Hub and Node) need 1 amp of current draw to transmit at full power.
PAGE 5
1 POWER INPUT: BATTERY INPUT: Battery Input: for 12 Volt Sealed Lead Acid (SLA) battery only. Solid Green LED = Battery charging Momentary Flashing LED = Battery is fully charged and a trickle/conditioning charge is occurring ED INDICATORS STATUS LEDs: 1 2 3 4 5 RECEIVE - flashes GREEN momentarily when a valid radio transmission is received. TRANSMIT - flashes RED momentarily when the unit transmits a packet as a result of an Relay Input change event or handshake.
PAGE 6
. RELAY DIAGRAM AND WIRING 1 RELAY INPUTS 2 RELAY OUTPUTS Relay Inputs - The Reign XRE-100 comes with 2 relay inputs. Connect DRY closure from devices relay to be extended. A closure on RLY1 input will result in a closure on RLY1 (NC/COM/NO) of the paired XRE-100. A closure on RLY2/COM input will result in a closure on RLY2 (NC/COM/NO output) of the paired XRE-100. Relay Outputs - The Reign XRE-100 comes with 2-relay outputs. Each output follows RELAY INPUTS from remote paired XRE-100.
PAGE 7
. ALERT RELAYS ALERT INPUT (when DIP switch 2 is on) Supervised inputs will detect an input shorted to ground (or each other) or an open input (loose or cut wire). Connect the supplied 1K ohm and 2K ohm resistors across the device to be monitored as shown. IMPORTANT: resistors must be connected at the device to be monitored NOT AT THE XRE-100 RELAY INPUT.
PAGE 8
DIP SWITCHES 1 MODE SWITCHES SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH 2 1 – PROG (PAIR) – Pairing mode when ON and Normal operating mode when OFF 2 – SUPERVISED INPUTS – Supervised inputs active when ON 3 – COMMS LOSS BEACON – Pulses Alert Relay if ON, otherwise Relay is steady on 4 – Not used 5 – Not used 6 – Not used RELAY OUTPUT SWITCH: Relay Output Switch - not used in XRE-100 to XRE-100 Relay Extension operation.
PAGE 9
. BATTERY BACKUP 12 Volt Sealed Lead Acid (SLA) battery only. Solid GREEN LED indicates battery charging. Momentarily flashing GREEN LED indicates battery is charged and a trickle/conditioning charge is occurring. . PAIRING IN THE FIELD PAIRING 1 2 3 4 Flip Dipswitch 1 to ON on both units. Press the PROG/TEST button on either unit NOTE: Observe the STATUS/PROG LED flashing. Flip Dipswitch 1 to OFF on both units Press PROG/TEST and observe TRANSMIT and RECEIVE LEDs operating normally.
PAGE 10
TROUBLESHOOTING XRE-100 units are not communicating: 1 - Check the Run LED. Normal operation will be orange LED flashing once a second. 2 - Press the red program button on the XRE-100. When pressed, the XRE-100 will send a radio test packet and the RED TRANSMIT LED will illuminate. If the paired XRE-100 is online, it will acknowledge with a radio test packet – indicated by a momentary on the green receive LED.
PAGE 11
WARRANTY The warranty period of this product is 24 months, beginning from the manufacturing date. During this period, if the product does not operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Transmitter Solutions. This warranty does not extend to the product casing which can be damaged by conditions outside of the control of Transmitter Solutions.
PAGE 12
PH 866.975.0101 • FX 866.975.0404 www.transmittersolutions.