Installation Instructions

ManualsBrandsTransmitter Solutions ManualsElectronicsReign - Safety Edge Receiver

WHAT’S INCLUDED

The REIGN Wireless Safety Edge Kit is a revolutionary product that will make any safety

edge set up wireless. This kit allows for all major safety edge technology to work with

any manufacturers operator. By using the proprietary Reign wireless technology we get

extreme range and penetration from the most reliable wireless edge kit on the market.

HOW IT WORKS...

Congratulations on your purchase of the Transmitter Solutions Wireless Safety Edge Kit. It has

been designed with state-of-the-art radio technology to allow for extreme range and penetration

allowing for maximum reliability.

The wireless safety edge kit comes factory paired with all the necessary components to get the

system up and running quickly. Simply install the batteries to the XET-100 and supply 8-24 VAC/

DC power to the XER-100 and you will be up and running.

1.28.20

EXTREME RANGE WIRELESS

SAFETY EDGE KIT

There are two pieces that complete the wireless edge kit. This kit includes the transmitter, which is

connected to the safety edge, part number XET-100. The second component of the kit is the

receiver, which is connected to the operator, part number XER-100.

R E IGN wire l ess

t e chno l o g y

Summary of content (12 pages)

PAGE 1
EXTREME RANGE WIRELESS SAFETY EDGE KIT v. 1.28.20 REIGN wireless technology The REIGN Wireless Safety Edge Kit is a revolutionary product that will make any safety edge set up wireless. This kit allows for all major safety edge technology to work with any manufacturers operator. By using the proprietary Reign wireless technology we get extreme range and penetration from the most reliable wireless edge kit on the market. WHAT’S INCLUDED There are two pieces that complete the wireless edge kit.
PAGE 2
CONTENTS: 1. F C C R E G U L A T O R Y S T A T E M E N T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 . BOARD CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 .
PAGE 3
1. FCC ID: (2ASPOXET100) and (2ASPOXER100): This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer-ence received, including interference that may cause undesired operation. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
PAGE 4
. .
PAGE 5
1 POWER INPUT: Power Input: 8 to 24 VOLTS AC/DC. 1 AMP Minimum. BATTERY INPUT: Battery Input: 2 AA Batteries ED INDICATORS STATUS LEDs: 1 2 3 Craig needs to update.
PAGE 6
. RELAY DIAGRAM AND WIRING 6
PAGE 7
PAGE 8
DIP SWITCHES 1 DIP SWITCHES: 8
PAGE 9
. JUMPERS 12 Volt Sealed Lead Acid (SLA) battery only. Solid GREEN LED indicates battery charging. Momentarily flashing GREEN LED indicates battery is charged and a trickle/conditioning charge is occurring.
PAGE 10
TROUBLESHOOTING XRE-100 units are not communicating: CRAIG TO FILL OUT 10
PAGE 11
WARRANTY The warranty period of this product is 24 months, beginning from the manufacturing date. During this period, if the product does not operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Transmitter Solutions. This warranty does not extend to the product casing which can be damaged by conditions outside of the control of Transmitter Solutions.
PAGE 12
PH 866.975.0101 • FX 866.975.0404 www.transmittersolutions.