Specifications

ManualsBrandsTransmitter Solutions ManualsElectronicsRemote Controller

WHAT’S INCLUDED

The

Reign TX-100 & XRE-100 transmitter/receiver kit is a

revolutionary product. This product allows for wirelessly triggering

a relay through a battery powered hand held transmitter with

extreme range, no line-of-sight wireless technology.

HOW IT WORKS...

Congratulations on your purchase of the Transmitter Solutions TX-100 to XRE-100 - Transmitter/Receiver kit. It has

been designed with state-of-the-art radio technology to provide maximum transmission through obstruction and

interference.

The TX-100 to XRE-100 kit

can be easily paired together with the program/learn button on the XRE-100 board.

Simply connect the Dry output closure to the device you are triggering and you will be up and running.

The TX-100 is a send/receiver unit that sends a signal when the button is pressed, indicated by a red LED light.

And receives a signal back, indicated by a green LED light. This allows users to know the signal was sent and

received by the corresponding XRE-100 unit.

v. . .1

T X – 100 & XRE – 100

TRANSMITTER & RECEIVER KIT

There are two pieces included in the TX-100 to XRE-100 kit.

The Reign TX-100 to XRE-100 kit in

cludes (1) TX-100 (transmitter) and (1) XRE-100 (receiver units.

R E IGN wire l ess

t e chno l o g y

Summary of content (12 pages)

PAGE 1
TX–100 & XRE–100 TRANSMITTER & RECEIVER KIT v. . .1 REIGN wireless technology The Reign TX-100 & XRE-100 transmitter/receiver kit is a revolutionary product. This product allows for wirelessly triggering a relay through a battery powered hand held transmitter with extreme range, no line-of-sight wireless technology. WHAT’S INCLUDED There are two pieces included in the TX-100 to XRE-100 kit. The Reign TX-100 to XRE-100 kit includes (1) TX-100 (transmitter) and (1) XRE-100 (receiver units. HOW IT WORKS...
PAGE 2
CONTENTS: 1. .............................................................. . RECEIVER SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 . TRANSMITTER SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . POWER DETAILS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
1. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
PAGE 4
. TRANSMITTER SPECIFICATIONS Minimum / Maximum Temperature Range: -40°F to 185°F (-40°C to 85°C) Security Encryption: AES Range: 1/2 mile (Through obstructions) Power: Micro-USB Rechargeable 1 2 3-1/2” 3 2-3/8” 1 2 3 MODE DIP SWITCHES SWITCH 1 – Learn Mode SWITCH 2 – Not used SWITCH 3 – Not used TRANSMIT LEVEL Clockwise for more power when transmitting. Counterclock wise for less power when transmitting.
PAGE 5
. POWER DETAILS The XRE-100 requires 1 amp of current draw to transmit at full power. IMPORTANT - XRE REQUIRES AT LEAST 1AMP POWER SUPPLY 1 1 2 POWER INPUT: Power Input: 12 to 24 VOLTS AC/DC. Always follow polarity when DC Power is used. 1 AMP Minimum 2 BATTERY INPUT: Battery Input: for 12 Volt Sealed Lead Acid (SLA) battery only.
PAGE 6
. LED INDICATORS STATUS LEDs: 1 2 3 RECEIVE - flashes GREEN momentarily when a valid radio transmission is received. TRANSMIT - flashes RED momentarily when the unit transmits a packet as a result of an Relay Input change event or handshake. STATUS/ PROG - flashes yellow patterns indicating status of the unit: pairing, error, etc. 4 RUN - flashes ORANGE 1 second ON and 1 second OFF indicating the microprocessor is running. 5 POWER LED - Glows solid orange when power is present.
PAGE 7
. RELAY DIAGRAM AND WIRING 1 RELAY OUTPUTS Relay Outputs - The Reign XRE-100 comes with 2-relay outputs. Relay 1 is the relay specified for use when the TX-100 is triggered. Relay 2 is used as a delay relay set for a certain amount of time to trigger after relay 1 is activated. Please refer to DIP switch 6 setting on page 8 for more information. The relay state is indicated by the Green ACTIVE LED above the relay.
PAGE 8
DIP SWITCHES 1 MODE SWITCHES SWITCH SWITCH SWITCH SWITCH 1 – PROG (PAIR) – Use for programming TX-100 to XRE-100 2 – Not used 3 – Not used 4 – Not used The behavior of the relay(s) is controlled by Dipswitch 5 & 6. SWITCH 5 = momentary or latching SWITCH 6 = single or dual relays DIPSWITCH 5 DIPSWITCH 6 OFF OFF ON OFF OFF ON OFF OFF 2 FUNCTION PROGRAM/TEST BUTTON: To program turn DIP switch 1 to the on position in both the XRE-100 and TX-100.
PAGE 9
2 1 3 . BATTERY BACKUP 12 Volt Sealed Lead Acid (SLA) battery only. Solid GREEN LED indicates battery charging. Momentarily flashing GREEN LED indicates battery is charged and a trickle/conditioning charge is occurring. . PAIRING UNIT IN THE FIELD To program turn DIP switch 1 to the on position in both the XRE-100 and TX-100. With both DIP switches turned on press the TX-100 transmit button. If done correctly the XRE-100 will flash yellow status LED 3 times and TX-100 will flash green LED 3 times.
PAGE 10
. TROUBLESHOOTING TX-100 & XRE-100 units are not communicating: 1 - Check the Run LED on the XRE-100. Normal operation will be orange LED flashing once a second. 2 - Press the button on the TX-100. When pressed, the TX-100 will send a radio test packet and the RED TRANSMIT LED will illuminate. If the paired XRE-100 is online, it will acknowledge with a radio test packet – indicated by a momentary on the green receive LED.
PAGE 11
WARRANTY The warranty period of this product is 24 months, beginning from the manufacturing date. During this period, if the product does not operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Transmitter Solutions. This warranty does not extend to the product casing which can be damaged by conditions outside of the control of Transmitter Solutions.
PAGE 12
PH 866.975.0101 • FX 866.975.0404 www.transmittersolutions.