User's Manual

ManualsBrandsTransCore ManualsComputers & AccessoriesRugged Computer

Table Of Contents

www.RoperMobile.com CMU056-A1 35

Return To Table of Contents

Operation Guide

USING THE VEHICLE CRADLE

A vehicle adapter/charger is required and is

available through Roper Mobile Technology (Part

Number CS312).

Vehicle Cradle Connector Identication

Back of Unit:

USB Host

USB Client

Power Supply

Fuse

Under the Unit:

Serial Port 1

Serial Port 2

Serial Port 3

Note: When installing and conguring peripherals,

ensure to select the proper Port (1, 2 or 3) and to

connect to the congured port once installation

complete.

Install power supply lead by inserting round

connector into the round connector at the

back of the cradle (refer back to connector

identication).

Turn ring clockwise to hold in place.

Connect other end of connector to cigarette

lighter.

Note:

The Vehicle Cradle requires a power source of

9 to 30 Vdc.

Ensure cigarette lighter connector is clean and

corrosion-free to provide the least electrical

resistance.

•

CBCE340BV with Optional Mount

Summary of content (15 pages)

PAGE 1
Operation Guide Using the Vehicle Cradle A vehicle adapter/charger is required and is available through Roper Mobile Technology (Part Number CS312). CBCE340BV with Optional Mount Vehicle Cradle Connector Identification Back of Unit: 1. 2. 3. 4. USB Host USB Client Power Supply Fuse 2 1 Under the Unit: 3 4 5. Serial Port 1 6. Serial Port 2 7.
PAGE 2
Operation Guide Using Vehicle Cradle (Continued) Making your own Power Supply Lead To make your own power supply lead, you may order the power connector at Roper Mobile Technology using the following information: • • Roper Mobile Technology item #: NAM036 Manufacturer’s name and item #: SwitchCraft 760K Note: • Be sure to insert a 3 amp time-lag fuse, or if you are using a fuse box, ensure to use a similar fuse. • All contacts must be clean and corrosion-free to avoid electrical resistance.
PAGE 3
Operation Guide Using Vehicle Cradle (Continued) Installing the Vehicle Mount (Continued) 1. Place one of the 2 balls underneath the cradle and align holes with the receptacles for the screws. 2. Tighten all 3 screws to secure balls into place. 3. Position the second any solid area in ball the against vehicle. 4. Secure into place by tightening 4 screws (not provided).
PAGE 4
Operation Guide Monitoring the Process on a 3 Serial Port Cradle A unique feature of the 3 Serial Port Cradle will allow you to monitor the process on the CE3000B screen. Note: A driver is required to ensure the 3 Serial Port Cradle (CBCE340BV) works correctly. For more information on the installation and configuration of the cradle, refer to the CE3000B Technical Guide located on Docudap technical web site.
PAGE 5
Operation Guide Monitoring the Process on a 3 Serial Port Cradle (Continued) Serial Port Connector Pin-Out Typical Communication Cable for Peripheral (Null Cable) Cradle Side Peripheral Side Female DB-9 Female-- DB-9 Typical Communication Cable for Peripheral Depends on the Peripheral Cradle Side Peripheral Side Female DB-9 Male DB-9 Depends on the Peripheral Return To Table of Contents www.RoperMobile.
PAGE 6
Operation Guide Field Replaceable Battery The CE3000B unit comes equipped with a field replaceable battery designed to ensure quick charging, long battery life and to withstand shocks and vibrations. It is strongly recommended to use batteries that are provided by Roper Mobile Technology or one of its distributors. Note: Check for our label on the battery pack. Warning Always turn the unit off prior to changing the battery to ensure no data is lost. 2.
PAGE 7
Operation Guide Field Replaceable Battery (Continued) 4. Replace with a fully charged Battery Pack. Note: Ensure to insert battery pack correctly or you may not be able to tighten screws. To lock To lock 5. Turn left screw upwards and right screw downwards to tighten and secure Battery Pack into place. (Refer to the illustration on the right). Return To Table of Contents www.RoperMobile.
PAGE 8
Adaptable Endcap Options Part Number 3240B-C 3240B-EEC 3240B-FC Description 1D/2D Barcode Reader Extended End-Cap Fingerprint & 1D/2D Barcode Reader 3240B-FEC Fingerprint Reader 3240B-LEC Laser Barcode Scanner 3240B-LF Laser Scanner & Fingerprint Reader 3240B-NEC Standard End-Cap 3240B-SCR Contact/Contactless SmartCard Reader 3240B-REC RS-232 DB9 End-Cap Return To Table of Contents 42 CMU056-A1 www.RoperMobile.
PAGE 9
Adaptable Endcap Options Barcode Readers Right Laser Scanner The ‘Laser Scanner’ function will depend application used and a special software Refer to your application’s User Guide for instructions. Information included are scanning instructions. on the driver. further basic Refer to the diagram to the right for right and wrong scanning methods. Wrong Testing the Scanner 1. To test the scanner, click on: a) Start b) Programs c) DAP Utilities d) CE Pad 2.
PAGE 10
Adaptable Endcap Options Barcode Readers (CONTINUED) 2D Barcode Reader This special option is usually installed and configured in-house at the manufacturer’s. The 2D Barcode Reader is primarily controlled by the client application and a special driver. Therefore, please refer to your application specialist or supervisor for further instructions. Note: You may also refer to the CE3000B Technical Guide located on DocuDap for further instructions on Testing the Reader 1.
PAGE 11
Adaptable Endcap Options Fast Fingerprint Sensor Testing the Fingerprint Sensor 1. Click on: a) Start b) Programs c) Dap Utilities d) Fingerprint 2. This “TFM window will Session is appear indicating not opened yet. 3. Click send to open session. 4. Wait until this message appears in the middle section of the window. Return To Table of Contents www.RoperMobile.
PAGE 12
Adaptable Encap Options Fast Fingerprint Sensor (Continued) Testing the Fingerprint Sensor (Continued) 5. Select 1 - OnEnroll from the drop down menu. 6. Enter New ID Number and click Send. 7. Place finger on Fingerprint Sensor and wait for fingerprint recognition. Return To Table of Contents 46 CMU056-A1 www.RoperMobile.
PAGE 13
Operation Guide Fast Fingerprint Sensor (Continued) Testing the Fingerprint Sensor (Continued) 1. If Fingerprint image was taken appropriately, this screen will appear. 2. If the image was read correctly, you may now verify database for fingerprint recognition. 3. Click “OnVerify” to verify fingerprint in Database. 4. Click “Send” and wait a few moments for a Database search. 5. After a few moments, the “Verification Result” will be displayed. 6. It will either indicate “Match” or “No Match”.
PAGE 14
Operation Guide SmartCard reader (Contact & Contactless) The CardMan® 5121 is based on a 13.56 MHz contactless Smart Card Interface that is compliant with ISO Specifications 14443 A, B and 15693. The reader works with a variety of 13.56 MHz contactless Smart Cards including but not limited to: • • • • • • Philips: MIFARE®, DESFire®, MIFARE ProX® Smart MX, and i.
PAGE 15
Advanced Settings Advanced Battery Options To See Power Remaining 1. Under Windows CE 5.0, click on: a) Start b) Settings c) Control Panel d) Power e) Battery Preserving Power It is possible to extend battery life by modifying the power delays of the unit, screen and backlighting settings. 1. To setup the screen and backlight delays, click on: a) Start b) Settings c) Control Panel d) _Power e) Power Off Battery Power Management All CE3000BB units are delivered with a calibrated Main Battery. 1.