User's Manual

ManualsBrandsTransCore ManualsComputers & AccessoriesRugged Computer

Table Of Contents

www.RoperMobile.com CMU056-A1 11

Return To Table of Contents

PRODUCT SPECIFICATIONS (CONTINUED)

ELECTRICAL &

ENVIRONMENTAL

REQUIREMENTS

(Continued)

Free Fall Drop Resistance (*):

Meets and exceeds IEC 68-2-32 method 1 (2

meter drop on concrete)

Meets and exceeds MIL-STD-810F method

516.4 procedure IV<

•

Electrostatic Discharge:

Meets EN 61000-4-2•

Approvals CE Certication• FCC Class B•

Warranty Manufacturer’s warranty: 1 year parts & labor Optional DAPCare Warranty extension available

Roper Mobile Technology reserves the right to change specications without notice.

WARNING / CAUTION / NOTE DEFINITION

The words WARNING, CAUTION, and NOTE carry special meanings and should be carefully reviewed.

WARNING

Alerts the reader about a situation, which if not avoided, could affect the proper functioning of the unit and

result in permanent damage to the unit.

CAUTION

Alerts the reader of a potentially hazardous situation, which if not avoided, may result in minor injury to the

user or may cause damage to the equipment. This includes special care necessary for the safe and effective

use of the device and the care necessary to avoid any damage that may occur as a result of use or misuse.

Note:

This provides special information to make important instructions clearer.

Introduction

Summary of content (9 pages)

PAGE 1
Introduction Product Specifications (Continued) ELECTRICAL & ENVIRONMENTAL REQUIREMENTS (Continued) Free Fall Drop Resistance (*): Electrostatic Discharge: • Meets and exceeds IEC 68-2-32 method 1 (2 • Meets EN 61000-4-2 meter drop on concrete) • Meets and exceeds MIL-STD-810F method 516.
PAGE 2
Symbols Warning, pay special attention. In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), this symbol indicates that the product must not be disposed of as unsorted municipal waste, but should be collected separately. Refer to your local distributor for return and/or collection systems available in your country. Caution must be used when this symbol is present. This symbol indicates a danger for laser radiation.
PAGE 3
Safety Precautions Warning • • • • • • • Refer to this Guide when inserting or removing batteries, cables or external peripherals. Operate and store your DAP unit within the temperature limits specified in this Guide. Do not use any pointed objects on the keyboard, door or mechanisms. Doing so may damage the unit. Use the ‘Stylus’ which has been provided with the unit by Roper Mobile Technology, as it has been designed with a non-abrasive material that cannot scratch or damage the touch screen.
PAGE 4
Quick Tour Front View 3 1. On/Off Key 5 2. Light Sensor 3. EndCap with aDAPtable Extension 4. Color Screen 2 5. Microphone 6. Battery Status Indicator 7. Cradle Communication Connector 8. Head-Set Adapter 10 9. Hand Strap Attachment 10. Trigger Button (both sides) 11. Function Key 4 12. Navigation Key (Left, Right, Top & Bottom) 7 12 8 11 1 6 9 Return To Table of Contents 14 CMU056-A1 www.RoperMobile.
PAGE 5
Quick Tour Back View 1. Release screws for PC & SDIO Card Access Door 1 2. Stylus (Pen) holder 3. Trigger Buttons (Left & Right) 4. Speaker 2 5. Release screws to change field replaceable battery (2 screws left and right). 4 3 3 5 Return To Table of Contents www.RoperMobile.
PAGE 6
Getting Started Warning Upon receiving your CE3000B unit, it is strongly recommended that you first charge the batteries prior to use. These following messages are likely to appear due to the length of time the unit was stored. When the battery reaches the low level, the battery status indicator will flash red. The Main Battery field will be highlighted as “Low” under the Battery or Status Tab. It will remain highlighted as long as the battery level is between 6% and 16%.
PAGE 7
Getting Started Charging the Battery 1. The installation requires the Modular Charger CSCE300-NA (North America - 110V / 120V AC Adapter) or the CSCE300-EU (Europe 220V) or the CSCE300-UK (United Kingdom 220 V). CSCE300-NA, CSCE300-EU, CECE300-UK 2. Insert modular charger into round connector (a) at the back of the cradle. 3. Connect the Modular Charger to the wall outlet. (a) 4. Insert unit into cradle.
PAGE 8
Getting Started Battery Status Indicator Color Definition Red Charger is connected and charging. Green Battery is fully charged. Blinking Red Warning, low battery Yellow Charger detected, but the battery charger temperature is too high or too low to recharge. Charge will start when temperature is adequate. No Light Power from the charger is not detected. Return To Table of Contents 18 CMU056-A1 www.RoperMobile.
PAGE 9
Operation Guide Turning the Unit On & Off Once charging is complete, the unit will automatically turn itself off after approximately 3 minutes. Turn Unit On 1. To turn on the CE3240B Unit, press the ON / OFF key for 2 seconds and release. Note: Should the unit not turn on, it could be because the battery is too low. Refer back to “Charging the Battery” Section for further instructions. Turning the Unit Off Manually There are two ways to turn the unit off: 1.