User's Manual

ManualsBrandsTransCore ManualsElectronicsLocation Monitoring Services Transmitter

Trusted Transportation Solutions

GoAnywhere Pass™

RUNNER

Installation Instructions

16-0092-001 Rev A 06/17

The GoAnywhere Pass Runner is an interior-mounted transponder that

is powered directly from the vehicle through a wire harness assembly

connected to switched power at the vehicle’s fuse panel. This product is

available in a hard-wired model or with a connector cable.

Transponder Instructions and Guidelines

Metallized Windshield

Some vehicle windshields contain a metallic treatment that could prevent an interior windshield-

mounted device from working correctly. If you have a vehicle with a metalized windshield, contact

your local customer service center for more information.

Windshield Band

Some windshields have a solid or dotted black frit band around the edges of the windshield

(Figure 1). The frit band protects the windshield mounting materials from the sun and ultra-violet

rays. The Runner transponder may be placed behind this band if necessary without aecting

performance.

Figure 1 – Windshield Frit Band

Hard-wired Connector Cable

Summary of content (10 pages)

PAGE 1
GoAnywhere Pass™ RUNNER Installation Instructions 16-0092-001 Rev A 06/17 The GoAnywhere Pass Runner is an interior-mounted transponder that is powered directly from the vehicle through a wire harness assembly connected to switched power at the vehicle’s fuse panel. This product is available in a hard-wired model or with a connector cable.
PAGE 2
Installation Instructions Runner Transponder Installation Required Supplies • Runner Transponder • Commercial glass cleaner and paper towels Determine Transponder Location The Runner transponder should be mounted on the interior windshield, with the longest side parallel to the bottom of the windshield. Other tags should be kept at least 3 inches away from the transponder. The area on the dashboard beneath the transponder must be kept clear of paperwork and metallic items. 1.
PAGE 3
Runner 2. If the vehicle has a two piece windshield, the Runner transponder should be mounted on the passenger side, 3 inches away from the center dividing bar and 4 inches above the dashboard (Figure 3). 3” 4” Windshield Wipers TA-0479 Figure 3 – Placement of Runner on two-piece windshield 3. Clean and dry the interior windshield surface completely. The windshield temperature must be at least 68ºF (20ºC) for optimum bonding. 4. Peel the backing off of the transponder to expose adhesive.
PAGE 4
Installation Instructions Standard Wiring Instructions Runner is powered directly from the vehicle through a power harness assembly connected to switched power at the vehicle’s fuse panel. To complete the installation of the Runner transponder, be sure that you have the parts listed in Table 1.
PAGE 5
Runner You may also need these tools in order to complete the installation: • Needle nose pliers • Screwdriver set • Socket set • Voltage meter • Wire crimper • Wire snips • Wire strippers Assemble the Power Cable and Harness Note: Connection to the power harness assembly will be located underneath the dashboard of your vehicle. 1. Run the Runner power cable through the gap between the bottom of the windshield and the dashboard assembly (Figure 4).
PAGE 6
Installation Instructions Figure 5 – Connect Runner cable to harness assembly Connect Cable to Vehicle Power 1. Locat a fuse (max. 25 Amp) in the fuse panel that has voltage present ONLY when the ignition switch is in the run/on position. 2. Remove the fuse. Using a voltage meter, determine which side of the fuse receptacle DOES NOT have power when the ignitition switch is in the run/on position. 3.
PAGE 7
Runner 4. Place fuse back into panel where it was removed. Make sure the fuse tap is on the side of fuse receptacle that DOES NOT have power when the ignition switch is in the run/on position. 5. Locate a ground attachment point. Find a bolt or nut that is attached to bare metal. 6. Secure the Black/Ground wire using the appropriate size ring terminal. 7. Zip ties may be used as needed to manage extra slack in the wiring assembly.
PAGE 8
Installation Instructions NO UNAUTHORIZED MODIFICATIONS STATEMENT Caution: This equipment may not be modified, altered, or changed in any way without permission from TransCore, LP. Unauthorized modification may void the equipment authorization from the FCC and will void the TransCore warranty. RADIO FREQUENCY INTERFERENCE STATEMENTS Note: This device complies with Part 15 of the FCC Rules and the Industry Canada Licence-Exempt RSS Standards.
PAGE 9
Runner Page 9
PAGE 10
For more information: Sales Support 800.923.4824 Technical Support 505.856.8007 transcore.com Trusted Transportation Solutions © 2017 TransCore L.P. All rights reserved. TRANSCORE is a registered trademark, and is used under license. All other trademarks listed are the property of their respective owners. Contents subject to change. Printed in the U.S.A.