User's Manual

ManualsBrandsTransCore ManualsElectronicsLocation Monitoring Services Transmitter

Trusted Transportation Solutions

PocketPass™

Installation Instructions

16-0046-001 Rev D 10/16

PocketPass is designed for mounting to a vehicle's interior windshield surface using

3M™ Dual Lock™ strips. This mounting method provides for easy mounting and removal

when portability is needed.

General Instructions and Guidelines

Proper Handling Prior to Installation

IMPORTANT: Prior to installation by the end user, PocketPass should be stored in the shielded bags and/or

packaging provided by TransCore. Failure to properly store tags will result in shortened battery life.

Metallized Windshield

Some vehicle windshields contain a metallic treatment that could prevent an interior windshield-mounted

device from working correctly. If you have a vehicle with a metalized windshield, contact your local customer

service center for more information. If your vehicle’s metalized windshield has a metal-free zone, it is typically

located near the rear view mirror.

Windshield Band

Some windshields have a solid or dotted black frit band around the edges of the windshield. The frit band

protects the windshield mounting materials from the sun and ultra-violet rays. The PocketPass may be placed

behind this band if necessary without aecting tag performance.

Figure 1 – Windshield frit band

Summary of content (8 pages)

PAGE 1
PocketPass™ Installation Instructions 16-0046-001 Rev D 10/16 PocketPass is designed for mounting to a vehicle's interior windshield surface using 3M™ Dual Lock™ strips. This mounting method provides for easy mounting and removal when portability is needed. General Instructions and Guidelines Proper Handling Prior to Installation IMPORTANT: Prior to installation by the end user, PocketPass should be stored in the shielded bags and/or packaging provided by TransCore.
PAGE 2
Installation Instructions PocketPass Activation Activating the PocketPass 1. Remove PocketPass from the shielded bag 2. Locate the battery door and find the battery protection tab (Figure 2). Figure 2 – Remove Battery Protection Tab 3. Keep the battery door closed while you pull and remove the battery protection tab. 4. Immediately after you remove the battery protection tab, a brief audio/visual sequence will occur as the PocketPass powers up.
PAGE 3
PocketPass Centered, 3” from bottom of windshield PocketPass should be placed above the windshield wipers TA-0443 Figure 3 – Placement of PocketPass on one-piece windshield 2. If the vehicle has a two piece windshield, the PocketPass should be mounted on the passenger side, 3 inches away from the center dividing bar, above the windshield wipers and 4 inches above the bottom of the windshield (Figure 4).
PAGE 4
Installation Instructions Installation with Dual Lock Strips 1. Clean and dry the interior windshield surface completely before affixing the Dual Lock strips. The windshield temperature must be at least 68ºF (20ºC) for optimum bonding. 2. Peel the backing off the Dual Lock strips to expose adhesive (Figure 5). Leave both sides of the Dual Lock strips pressed together to ensure the strips will align between the PocketPass and windshield. Apply the PocketPass to the windshield using moderate pressure.
PAGE 5
PocketPass PocketPass Battery Replacement Two lithium AAA batteries are pre-installed in your PocketPass. NOTE: For proper operation, the PocketPass requires lithium batteries. TransCore recommends Energizer® Advanced Lithium AAA batteries. To replace the batteries, remove the PocketPass from the windshield as described in Step 3 on page 4. 1. Hold the PocketPass with the LED side facing down. Locate the battery door.
PAGE 6
Installation Instructions Audio/Visual Signals Your PocketPass is equipped with audio/visual signals that will alert you about certain conditions relevant to your tag. Refer to Table 1 for a list of audio and visual signals for your tag.
PAGE 7
PocketPass NO UNAUTHORIZED MODIFICATIONS STATEMENT Caution: This equipment may not be modified, altered, or changed in any way without permission from TransCore, LP. Unauthorized modification may void the equipment authorization from the FCC and will void the TransCore warranty. RADIO FREQUENCY INTERFERENCE STATEMENTS Note: This device complies with Part 15 of the FCC Rules and the Industry Canada Licence-Exempt RSS Standards.
PAGE 8
For more information: Sales Support 800.923.4824 Technical Support 505.856.8007 transcore.com Trusted Transportation Solutions © 2016 TransCore L.P. All rights reserved. TRANSCORE and TRANSSUITE are registered trademarks, and are used under license. All other trademarks listed are the property of their respective owners. Contents subject to change. Printed in the U.S.A.