Installation Instructions

ManualsBrandsTransCore ManualsElectronicsMobile Transponder LMS Tag

Trusted Transportation Solutions

Vehicle Powered

RV Toll Pass

for Class A Motor Homes

16-0188-001 Rev A X2 6/22

The RV Toll Pass is an interior-mounted transponder, powered directly from

the vehicle through a wire harness assembly connected to switched power.

The RV Toll Pass can be powered from a vehicle fuse panel. Factory

installations may utilize the vehicle power rail. The transponder may also be

concealed in a vehicle headliner or securely attached to a vehicle windshield.

These instructions provide general guidelines for these types of installations.

This information is intended for use by authorized TransCore dealers,

installers, and service personnel.

Summary of content (11 pages)

PAGE 1
Vehicle Powered RV Toll Pass Installation Instructions for Class A Motor Homes 16-0188-001 Rev A X2 6/22 The RV Toll Pass is an interior-mounted transponder, powered directly from the vehicle through a wire harness assembly connected to switched power. The RV Toll Pass can be powered from a vehicle fuse panel. Factory installations may utilize the vehicle power rail. The transponder may also be concealed in a vehicle headliner or securely attached to a vehicle windshield.
PAGE 2
Installation Instructions Supplies Needed for Installation Before you begin, open the installation kit to ensure that you have all of the parts listed in Table 1, and review the recommended tools and supplies. Note: The harness assembly should be installed into the vehicle by a qualified technician.
PAGE 3
RV Toll Pass Power Harness Assembly The RV Toll Pass transponder should be connected to the vehicle fuse panel through a power harness made specifically for the transponder. Figure 1 shows a diagram of the RV Toll Pass transponder and power harness assembly. CAUTION: Do not power the RV Toll Pass transponder directly from 12/24VDC. You must use the power harness assembly.
PAGE 4
Installation Instructions Connecting Power Harness to Vehicle Fuse Panel Note: Refer to Figure 1 for a diagram of the terms shown in bold text. 1. Locate the black and red wire pair on the power harness. Trim wire length as required. Crimp one of the supplied quick disconnects onto the red wire. Ensure that the crimped connection is secure (Figure 2). Figure 2 – Crimp Quick Disconnect onto Red Wire 2. Crimp one of the supplied ring terminals onto the black wire (Figure 3).
PAGE 5
RV Toll Pass 4. Locate a fuse (max. 25 Amp) in the fuse panel that has voltage present ONLY when the ignition switch is in the key on/engine off position. 5. Remove the fuse. Using a voltage meter, determine which side of the fuse receptacle DOES NOT have power when the ignition switch is in the key on/engine off position and attach a fuse tap to that side. CAUTION: Do NOT place fuse taps on the hot side of the fuse. 6.
PAGE 6
Installation Instructions Installing Transponder in Headliner Note: For transponder mounting or location questions, contact TransCore Technical Support. The RV Toll Pass transponder may be concealed in the vehicle headliner as close as possible to the front of the vehicle and windshield. The transponder must be horizontally polarized, on a nonmetallic or non-carbon fiber surface, at least 4 inches away from any metal. 1. Determine the proper location for the transponder. 2.
PAGE 7
RV Toll Pass 3. Connect the power cable to the transponder (Figure 6). Ensure that the cable is connected securely. Figure 6 – Connect the Power Cable to the Transponder 4. Once the optimal mounting location is determined, prepare the mounting surface, making sure that the area is free of dust, dirt, and debris. 5. Peel the backing off of the transponder to expose the adhesive. Apply the transponder using moderate pressure.
PAGE 8
Installation Instructions 2. Connect the power cable to the transponder. Refer to Figure 6 on page 7. Ensure that the cable is connected securely. 3. Once the optimal mounting location is determined, prepare the mounting surface, making sure that the area is free of dust, dirt, and debris. The windshield temperature should be at least 68ºF (20ºC) for optimum bonding. 4. Peel the backing off of the transponder to expose adhesive. Apply the transponder using moderate pressure.
PAGE 9
RV Toll Pass Uninstalling Transponder Mounted with Adhesive Tape When the Transponder is installed on a vehicle mounting surface using high-bond adhesive tape, installation is semi-permanent and the transponder cannot be moved once the installation is complete. If the transponder needs to be removed, a tool specifically designed for removing high-bond tape should be used (Figure 9). Failure to do so can result in damage to the mounting surface.
PAGE 10
Installation Instructions FCC ID: FIH051120 IC: 1584A-051120 NO UNAUTHORIZED MODIFICATIONS STATEMENT CAUTION: This equipment may not be modified, altered, or changed in any way without permission from TransCore, LP. Unauthorized modification may void the equipment authorization from the FCC and will void the TransCore warranty. RADIO FREQUENCY INTERFERENCE STATEMENTS Note: This device complies with Part 15 of the FCC Rules and the Industry Canada Licence-Exempt RSS Standards.
PAGE 11
For more information: Sales Support 800.923.4824 Technical Support 505.856.8007 transcore.com © 2022 TransCore L.P. All rights reserved. TRANSCORE is a registered trademark and is used under license. All other trademarks listed are the property of their respective owners. Contents subject to change. Printed in the U.S.A.