Installation Instructions

ManualsBrandsTransCore ManualsElectronicsMobile transponder LMS Tag

Trusted Transportation Solutions

16-6200-012 Rev X2 1/20

JED

TransCore’s JED is an IAG radio

frequency identiﬁcation (RFID) tag with

integrated technology for easy user

conﬁguration.

The JED can be conﬁgured with a

3-position switch, allowing users to

manually select from 3 options. It is

also available in a non-switchable case.

A multi-color LED can be included in

the case conﬁguration when visual

feedback is desired.

General Installation Information

Metallized Windshields: Some vehicle windshields contain a metallic treatment that could prevent an

interior windshield-mounted tag from working correctly. If you have a vehicle with a metallized windshield,

you may need to install an exterior tag on your vehicle instead of the interior windshield-mounted tag.

Contact your local tag customer service center for more information.

Metal-Free Zone: Some vehicles with metallized windshields have a metal-free zone, usually located near

the rearview mirror. If your windshield has this zone, center the tag in that area and follow the installation

instructions listed in these pages.

Tinted Windshield: Some vehicles have a metallic tint across the top of the windshield that might interfere

with reading the tag. If your windshield has this metallic tint, install the tag at least 2 inches (5.1 cm) below

the tinted area. Nonmetallic tint does not aect tag performance.

Metal Sun Visors: Some vehicles have an exterior-mounted sun visor that might interfere with reading the

tag. If your vehicle has this visor, mount the tag at least 2 inches (5.1 cm) below the visor.

Summary of content (6 pages)

PAGE 1
JED Installation Instructions 16-6200-012 Rev X2 1/20 TransCore’s JED is an IAG radio frequency identification (RFID) tag with integrated technology for easy user configuration. The JED can be configured with a 3-position switch, allowing users to manually select from 3 options. It is also available in a non-switchable case. A multi-color LED can be included in the case configuration when visual feedback is desired.
PAGE 2
Installation Instructions Tag Installation and Removal Procedures The JED tag is designed for mounting to a vehicle’s interior windshield surface. It may be equipped with 3M™ Dual Lock™, hook-and-loop, or suction cups. Required Supplies • JED • Commercial glass cleaner and paper towels Installing the Tag Choose the location for your tag (Figure 1). The tag should be mounted approximately 1 inch (2.54 cm) below the rear view mirror post.
PAGE 3
JED Tag 2. Hold the tag so that the printed text or image is right side up and facing toward you ( Figure 3). Press the tag against the windshield and hold for 10 seconds. Note: When installing the tag using the mounting strips for the first time, leave the tag in place for at least 24 hours to allow the adhesive to cure. Figure 3 Correct Tag Orientation TA0444-002 Suction cups 1. Hold the tag so that the printed text or image is right side up and facing toward you (Figure 3). 2.
PAGE 4
Installation Instructions NO UNAUTHORIZED MODIFICATIONS STATEMENT CAUTION: THIS EQUIPMENT MAY NOT BE MODIFIED, ALTERED, OR CHANGED IN ANY WAY WITHOUT PERMISSION. UNAUTHORIZED MODIFICATION MAY VOID THE EQUIPMENT AUTHORIZATION FROM THE FCC AND WILL VOID THE WARRANTY. AUCUNE MODIFICATION NON AUTORISÉE MISE EN GARDE : IL EST INTERDIT DE MODIFIER, D’ALTÉRER OU D’APPORTER DES CHANGEMENTS À CET APPAREIL DE QUELQUE MANIÈRE QUE CE SOIT SANS AUTORISATION.
PAGE 5
PAGE 6
For more information: Sales Support 800.923.4824 Technical Support 505.856.8007 transcore.com Trusted Transportation Solutions © 2020 TransCore LP. All rights reserved. TRANSCORE is a registered trademark and is used under license. All other trademarks listed are the property of their respective owners. Contents subject to change. Printed in the U.S.A.