Installation Instructions

ManualsBrandsTransCore ManualsElectronicsMobile mounted LMS Tag

Trusted Transportation Solutions

16-0116-001 Rev X3 11/18

P2 Tag

TransCore’s P2 Tag allows independent data functions within the same tag.

The switchable design allows the driver to select between three dierent

accounts by simply toggling a switch.

General Installation Information

Metallized Windshields: Some vehicle windshields contain a metallic treatment that could prevent an interior

windshield-mounted tag from working correctly. If you have a vehicle with a metallized windshield, you may need

to install an exterior tag on your vehicle instead of the interior windshield-mounted tag. Contact your local tag

customer service center for more information.

Metal-Free Zone: Some vehicles with metallized windshields have a metal-free zone, usually located near the

rear view mirror. If your windshield has this zone, center the tag in that area and follow the installation instructions

listed in these pages.

Tinted Windshield: Some vehicles have a metallic tint across the top of the windshield that might interfere with

reading the tag. If your windshield has this metallic tint, install the tag at least 2 inches (5.1 cm) below the tinted

area. Nonmetallic tint does not aect tag performance.

Metal Sun Visors: Some vehicles have an exterior-mounted sun visor that might interfere with reading the tag. If

your vehicle has this visor, mount the tag at least 2 inches (5.1 cm) below the visor.

Summary of content (6 pages)

PAGE 1
P2 Tag Installation Instructions 16-0116-001 Rev X3 11/18 TransCore’s P2 Tag allows independent data functions within the same tag. The switchable design allows the driver to select between three different accounts by simply toggling a switch. General Installation Information Metallized Windshields: Some vehicle windshields contain a metallic treatment that could prevent an interior windshield-mounted tag from working correctly.
PAGE 2
Installation Instructions Required Supplies • P2 Tag • Commercial glass cleaner and paper towels Tag Installation and Removal Procedures The P2 Tag is designed for mounting to a vehicle’s interior windshield surface. It may be equipped with 3M™ Dual Lock™, hook-and-loop, or double-sided tape strips; or suction cups. To install the tag Choose the location for your tag (Figure 1). The tag should be mounted approximately 1 inch (2.54 cm) below the rear view mirror post.
PAGE 3
P2 Tag TA0445 Figure 2 – Peel backing off of the Dual Lock, hook-and-loop, or double-sided tape strips to expose adhesive 2. Hold the tag so that the printed text or image is right side up and facing toward you (Figure 3). Press the tag against the windshield and hold for 10 seconds. Note: When installing the tag using the Dual Lock, hook-and-loop, or double-sided tape strips for the first time, leave the tag in place for at least 24 hours to allow the adhesive to cure.
PAGE 4
Installation Instructions Selecting Nomination Mode or Account Type The P2 Tag uses a three-position switch to change from one account type to another. Each tag can be programmed with three accounts. For example, your tag may be programmed for “Single Occupancy Vehicle,” “High Occupancy Vehicle”, “Private Account,” or “Business Account”, depending on the desired application. The tag will have designations for the 3 account types printed directly on the case or on labels which have been applied to the case.
PAGE 5
P2 Tag NO UNAUTHORIZED MODIFICATIONS STATEMENT CAUTION: THIS EQUIPMENT MAY NOT BE MODIFIED, ALTERED, OR CHANGED IN ANY WAY WITHOUT PERMISSION. UNAUTHORIZED MODIFICATION MAY VOID THE EQUIPMENT AUTHORIZATION FROM THE FCC AND WILL VOID THE WARRANTY. AUCUNE MODIFICATION NON AUTORISÉE MISE EN GARDE : IL EST INTERDIT DE MODIFIER, D’ALTÉRER OU D’APPORTER DES CHANGEMENTS À CET APPAREIL DE QUELQUE MANIÈRE QUE CE SOIT SANS AUTORISATION.
PAGE 6
For more information: Sales Support 800.923.4824 Technical Support 505.856.8007 transcore.com Trusted Transportation Solutions © 2018 TransCore LP. All rights reserved. TRANSCORE is a registered trademark and is used under license. All other trademarks listed are the property of their respective owners. Contents subject to change. Printed in the U.S.A.