User’s Manual Body Camera DrivePro Body 52 TS32GDPB52A (Version 1.
Table of Contents 1. Introduction.....................................................................................................................................3 2. System Requirements.................................................................................................................. 4 3. Getting Started...............................................................................................................................5 3-1 Function Buttons......................................
1. Introduction Transcend’s DrivePro Body 52 is an easy-to-operate wearable video camera that is tailor-made for police officers, security guards and other professionals to capture real time videos and photos of events. The Wi-Fi network allows live streaming to your smartphone and modifying the function setting using the DrivePro Body App.
2. System Requirements System requirements for connecting the DrivePro Body 52 to a computer and for using the DrivePro Body Toolbox: A desktop or a laptop with a working USB port Windows® 7 Windows® 8 Windows® 8.
3. Getting Started 3-1 Function Buttons Warning Indicator Buzzer Power Button Snapshot / Wi-Fi Button Built-in Microphone Recording / Wi-Fi Indicator Reset Button 3.
3-2 Charging the DrivePro Body 52 Before use, please ensure that the battery is fully charged. Charge the DrivePro Body 52 via the bundled USB 2.0 to 3.5mm DC power cable. A flashing orange LED light of the warning indicator is visible while charging; the orange LED light will turn off when fully charged. To charge the DrivePro Body 52, you can either: 1. Connect the 3.5mm DC power cable to a wall outlet with the included adapter. 2. Connect the 3.5mm jack of the camera and the USB to a computer.
LED Status Definition Flashing Recording Flashing Recording with Wi-Fi on Solid Backup mode / Settings 4. Recording Videos To start recording, long press the button; you will hear 1 beep, and the red LED light of the recording indicator will flash during recording. To activate Wi-Fi, long press the button while recording, and the LED light will flash from red to blue. To stop recording, long press the button again; you will hear 1 beep. The red LED light will then turn off.
5. Taking Photos To take photos while recording, quickly press the button, you will hear 1 beep. 6. Using the DrivePro Body 52 App Developed for iOS and Android devices, the free DrivePro Body App allows you to wirelessly adjust the settings of the camera and to live-stream video on your smartphone. 6-1 Downloading and Installing the App 1. Search and download DrivePro Body on your App Store or Google Play. 2. Download and install the DrivePro App.
Note: 1. To change the default SSID and password, go to Settings in the DrivePro App. 2. The camera stops recording when you go to Data or Settings, and will resume recording when you tap Liveview. 6-3 Playing Videos and Browsing Photos 1. Tap Data. 2. To play the videos recorded, tap VIDEO and select the desired file. 3. To browse the photos taken, tap PHOTO and select the desired file. 6-4 Settings In the Settings menu, you can adjust the settings of video, device, Wi-Fi and System.
12345678). Version: Tap to upgrade the firmware to the latest version. WARNING: NEVER remove the power cord or the microSD memory card while the firmware is being upgraded. 1. The DrivePro 520 will shut down and the red LED light will flash while the firmware is being upgraded. After the upgrade is complete, the DrivePro will restart automatically. 2. If the DrivePro cannot be turned on due to firmware upgrade failure, please contact Transcend customer service for technical support. 7.
Clean the DrivePro Body 52 surface with a soft cloth slightly moistened with water, then wipe the surface with a dry cloth. Do not use any of the following as they may damage the finish or the casing: Chemical products such as thinner, benzine, alcohol, disposable cloths, insect repellent, sunscreen orinsecticide, etc. Do not touch the camera with any of the above on your hand. Do not leave the camera in contact with rubber or vinyl for a long time.
9. IPX4 Water Resistant The camera body of the DrivePro Body 52 is IPX4 water resistant (not waterproof), offering protection against splashing water from any direction. However, it is not protected against pressurized water such as from a shower or tap. WARNING: DrivePro Body 52 is not water resistant when connected to the power cable. Failure caused from incorrect use is not covered by the limited warranty. Do not use the DrivePro Body 52 in water as it is not waterproof.
Velcro Note: Clip & Velcro holders Quick Start Guide Warranty Card
11. Specifications Connect Interface USB 2.0 Storage Capacity Built-in MLC-based microSD, 32GB internal storage Dimensions Weight 88.4 mm (L) × 52.2 mm (W)× 19.4 mm (H) 3.48” (L) x 2.06” (W) x 0.76” (H) 88g 3.1 oz Battery Li-Polymer 1530mAh Power Supply Input: AC100V-240V, 50-60Hz, 0.4A Max Output: DC5V 2A Recording Life Up to 3.5 hours* Operating Temperature -20°C (-4°F) ~ 65°C (149°F) -20°C (-4°F) ~ 45°C(113°F)* Video Format H.
again. Make sure that both ends of the USB cables are properly connected as shown in the User’s Manual. 2. Is your DrivePro Body 52 connected to the Mac keyboard? If yes, try to plug it in an available USB port on your Mac Desktop directly. 3. Is the computer’s USB ports enabled? If not, refer to the user’s manual of your computer (or motherboard) to enable them. None of the DrivePro Body 52 buttons are responding.
13. Recycling and Environmental Protection Recycling the Product (WEEE): Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When you see the crossed-out wheel bin symbol attached to a product, it means that the product is covered by the European Directive 2002/96/EC: Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products.
14. Two-year Limited Warranty This product is covered by a Two-year Limited Warranty. Should your product fail under normal use within two years from the original purchase date, Transcend will provide warranty service pursuant to the terms of the Transcend Warranty Policy. Proof of the original purchase date is required for warranty service. Transcend will inspect the product and in its sole discretion repair or replace it with a refurbished product or functional equivalent.
15. GNU General Public License (GPL) Disclosure Firmware incorporated into this product and/or software used for this product may include third party copyrighted software licensed under the GPL (hereinafter referred to as “GPL Software”).
for any purpose other than in connection with the Product or in a manner inconsistent with the design or documentations of the Licensed Software; (b) license, distribute, lease, rent, lend, transfer, assign or otherwise dispose of the Licensed Software or use the Licensed Software in any commercial hosted or service bureau environment; (c) reverse engineer, decompile, disassemble or attempt to discover the source code for or any trade secrets related to the Licensed Software, except and only to the extent t
8. Limitation of Liability. IN ANY CASE, TRANSCEND 'S LIABILITY ARISING OUT OF OR IN CONNECTION WITH THIS AGREEMENT WILL BE LIMITED TO THE TOTAL AMOUNT ACTUALLY AND ORIGINALLY PAID AT RETAIL BY CUSTOMER FOR THE PRODUCT. The foregoing Disclaimer and Limitation of Liability will apply to the maximum extent permitted by applicable law. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the exclusions and limitations set forth above may not apply. 9.
17. Federal Communications Commission (FCC) Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation. This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.