RF-BTR-319 Bluetooth Audio Receiver With A2DP, Qualcomm® aptX® HD, aptX® supported and With NFCTM Fast paring and connection. Feature ◎ aptX HD, aptX codec support ◎ NFC Quick link support ◎ SBC codec support ◎ A2DP Bluetooth profile supported ® ® ◎ 33 feet(10M) effective range ◎ TOSLINK digital audio output ◎ Audio RL audio output ◎ 8 devices ID storable What’s in the box Main unit AC/DC adaptor 3.5mm male male audio cable Setup your RF-BTR319 1 3.
Analogue connection 1. Connect one 3.5mm end of the include audio to headphone jacket on the RF-BTR319 2. Connect the other end to an audio input on your home stereo system (3.5mm or 3.5mm + 3.5mmm2 RCA). Consult your stereo user’s manual for more information on how to accomplish this. Digital connection 1. Connect one TOSLINK cable end to optical jacket on the RF-BTR319 (recommended) 2. Connect the other end to one TOSLINK input of your home stereo system.
Step 2 : Turn on the NFC function Back to setting page Check NFC function Turn on NFC function Step3: Fast Connection using NFC TAP the Smartphone to on The NFC logo on RF-BTR319 *The message will pop up Please choose YES *Some device will pop up Some will not” Pairing First 3 Connection, if connected you can play music now
Step4: Disconnected you device and RF-BTR319 If you wan to disconnect, you need to tap the Smartphone to RF-BTR319 again. Then the connection between RF-BTR319 and your device will off. Pairing your RF-BTR319 for no NFC device iPad/iPhone/iPod touch 1. Go to Bluetooth manager of your iPad/iPhone/iPod touch by the following steps 1 .From your iPad/iPhone/iPod touch home page, tap “setting” 2. Inside Settings tap on “Bluetooth” 4 3.
4.Your iPod/iPhone/iPad will auto searching available device. You will see “Music Receiver” then Tap on it. 5. Your iPod/iPhone/iPad connected to RF-BTR319 Now. And You can play music from your iPod/iPhone/iPad. 7. Your iPod/iPhone/iPad will disconnect. 5 6.
Android Phone/Tablet(ver 9.0 as Example with aptX HD support) 1. Go to Bluetooth manager of your smart phone by the following step 1. From your smart phone 2. Inside the setting, turn on home page, tap on “setting” The Bluetooth 4. Searched Bluetooth Devices will show up, please tap on “RF-BTR319” 5. Once paired, the blue LED light on the RF-BTR319 will flash once.
Note: Some devices, such as iPhone, will connect immediately after pairing so the LED will ON. Other devices, such as notebook, may ask you if you wish to connect and LED will go off after pairing until a connection is established. Although the RF-BTR319 can only play music from one device at a time, it is capable of being paired to up to 8 devices. You can play the music now. Just play music on your device as you normally would and the sound will come out from your stereo system.
Indication of LED Indication meaning Description Flash once 1 sec per 5 secs Power on /Pairing Waiting for connection Permanent Lighted connected Device and main unit are connected Troubleshooting You can solve your problems from this section No music out from my stereo speaker ◎ Make sure the RF-BTR319 is powered.
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
IC Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference,and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.