User's Manual

ManualsBrandsTrans Electric ManualsElectronicsPortable Bluetooth Wireless Transmitter & Receiver

Pairing your wireless adapter (RX mode)

1 Add LED behaviors so amend as below:Press and hold the MFB button for three seconds to enter to pairing mode. And Red and Blue LED blinks alternatively.

2 Turn on Bluetooth on your smartphone and set it to pairing mode.

3 When your adapter and device is connected, the blue LED blinks once every ve second. Then music can be played.

PACKAGE CONTENTS

• Wireless adapter

• USB to USB-C cable

• 3.5 mm audio cable

• Soft pouch

• Quick Setup Guide

FEATURES

• Receives or transmits Bluetooth signals to add connectivity to many devices,

including listening through two headphones simultaneously

• LEVEL mode optimizes audio performance

• Two ports let you charge the device using a USB-C or Lightning cable (not

included)

• Up to 16 hours (transmitter mode) or up to 13 hours (receiver mode) of battery

life keeps your device working longer.

OVERVIEW

Front Back

CHARGING YOUR ADAPTER

• Plug the included USB to USB-C cable or a Lightning cable (not included) into

your wall charger. Plug the other end of the cable into the USB-C or Lightning

port on your adapter.

Notes:

• Do not use the USB-C and Lightning ports

on your adapter at the same time.

• You can use a USB-C to USB-C cable (not

included) to charge your adapter if the

power draw is less than 100W.

• When the battery is charging, the red LED

lights solid.

• When the battery is fully charged, the red

TRANSMITTER MODE

In transmitter mode, you can connect your adapter to a media source, and play the audio on your earbuds or headset via Bluetooth.

Setting up your wireless adapter (TX mode)

1 Switch to “TX” mode.

2 Connect one end of the included audio cable to the 3.5 mm jack on your adapter.

3 Connect the other end to an audio output on your media source.

• Press 1.5 second to turn on the adapter. The adapter will connect back to last paired devices.

• When turn on rst time, Red and Blue LED blinks. When connected, the Blue LED blinks once every ve seconds.

1 Put your Bluetooth headphone or Bluetooth music receiver in pairing mode. Consult the documentation for those devices for more information.

2 Add LED behaviors so amend as below: Press and hold the MFB button for three seconds to enter to pairing mode. And Red and Blue LED blinks alternatively.

Connect to the second headset or music receiver

1 Put your second Bluetooth headphones or music receiver into pairing mode. Consult the documentation for those devices for more information.

2 Press the MFB button twice to pair with a second device. The blue LED blinks quickly for two minutes while pairing.

evices simultaneously.

RECEIVER MODE

In receiver mode, your adapter can receive audio from your Bluetooth device and send the signal to be played on stereo speakers.

Setting up your wireless adapter (RX mode)

1 Switch to “RX” mode.

2 Connect one end of the included audio cable to the 3.5 mm jack on your adapter.

3 Connect the other end to an audio input on your home stereo system. See your stereo’s user manual for more information on connections.

Before using your new product, read these instructions to prevent any damage.

QUICK SETUP GUIDE

Bluetooth Wireless

Transmitter &

Receiver

Flat size (W×H): 15.75 × 10.63 in. (400 × 270 mm)

Final folded size: 3.15 × 3.5 in. (80 × 90 mm)

correct mode.

• If you want to clear all saved devices, press and hold the MFB button for seven

seconds while the adapter is o. The Red LED blinks slowly 5 times to indicate

devices cleared then enter into pairing mode.

TROUBLESHOOTING

No power.

• Make sure that your adapter power cable is connected to your adapter and a power

outlet.

• Make sure that your adapter is turned on.

No sound or low volume

TX mode:

• Shorten the distance between your devices and adapter.

• Make sure that all connections are secure.

• Turn up the volume on your media source.

• Make sure that your earbuds or headset has a Bluetooth connection with your

adapter.

RX mode:

• Shorten the distance between your devices and adapter.

• Make sure that all connections are secure.

• Turn up the volume on your media source.

• Make sure that your media source has a Bluetooth connection with your adapter.

Cannot establish a Bluetooth connection.

• Shorten the distance between your adapter and your Bluetooth device.

• Make sure that you have selected Insignia NS-HPBTAA23 on your Bluetooth

device.

• Make sure that your adapter is not paired to another Bluetooth device.

• Make sure that your adapter and Bluetooth device are both in pairing mode.

• Make sure that your Bluetooth device is not connected to any other device.

My adapter does not appear on my Bluetooth device.

• Shorten the distance between your adapter and your Bluetooth device.

• Put your adapter into pairing mode, then refresh your list of Bluetooth devices. For

more information, see the documentation that came with your Bluetooth device.

SAFETY WARNINGS

• The adapter requires full connection and both hands to install.

• The adapter has Lithium – Polymer batteries. Please do not open the unit to

prevent unwanted short circuit happening.

• Do not use the adapter near water (for example, a bath tub, wash bowl, kitchen

sink, laundry tub, wet basement, swimming pool, or other areas located near

water).

• Clean with a dry cloth.

•

the adapter before cleaning.

• Install the adapter far away from heat sources.

• Use only the attached accessories.

•

the adapter when unused for long time.

SPECIFICATIONS

Dimensions (H×W×D): 2.05 × 1.54 × 0.6 in. (5.2 × 3.9 × 1.53 cm)

Weight: .049 lbs. (0.022 kg)

Charging input: 5V/0.2A USB-C or Lightning

Audio input/output: 3.5 mm

Bluetooth range: 66 ft. (20 m)

Note: Range may vary on your other Bluetooth devices.

Bluetooth version: BT 5.3

Codec compatibility: SBC

LEGAL NOTICES

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution

authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

RSS-Gen Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Ce dispositif contient des émetteurs exonérés de permis(s)/récepteurs)s qui sont conformes aux RSS (s) exemptés

de licence du Canada. L’opération est soumise aux deux conditions suivantes :

1. Cet appareil peut ne pas causer d’interférences.

2. Ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent provoquer un

fonctionnement indésirable de l’appareil.

RSS-102 Statement

This equipment complies with Innovation, Science and Economic Development Canada’s radiation exposu

re limits

set forth for an uncontrolled environment.

Cet équipement est conforme aux limites d’exposition aux rayonnements de Développement économique Canada

pour l’innovation, les sciences et le développement économique établies dans un environnement incontrôlé.

Visit www.insigniaproducts.com for details.

CONTACT INSIGNIA:

For customer service, call 1-877-467-4289 (U.S. and Canada)

www.insigniaproducts.com

Distributed by Best Buy Purchasing, LLC

USB-C

charging port

Lightning

charging port

LED

Mode switch

Level switch

3.5 mm stereo

MFB button

USB-A to USB-C cable

(included)

Lightning cable

(not included)

Optimize volume and sound quality (TX mode)

• When you connect your earbuds with your adapter and the audio is too low, too loud, or overdrive clipping distortion,

you can slide the level switch to optimize the volume.

Understanding LED indicators (TX mode)

INDICATOR

Red and blue LEDs blink alternatively for 1 second

Blue and red LEDS blink alternatively for 1 second

Red and blue blinking

Blue LED blinks once every 5 seconds

DESCRIPTION

Adapter is turned on

Searching for Bluetooth device

One Bluetooth device is connected

INDICATOR

Blue LED blinks twice every 5 seconds

Red LED blinks slowly 5 times

Blue LED blinks quickly

Blue LED blinks slowly

DESCRIPTION

Two Bluetooth devices are connected

Saved devices cleared

Searching for second Bluetooth device

Disconnected from Bluetooth device

V1 ENGLISH 22-0396

(Long cable not included)

TX mode

3.5 mm audio cable

(included)

Media source

*For the best performance, do not place behind your TV

Headset

2nd paired

Earbuds

1st paired

Note: Due to Bluetooth limitations, expect

delays between video and audio signals.

RX mode

RESET YOUR WIRELESS ADAPTER

USING YOUR WIRELESS ADAPTER (RX MODE)

• Press 1.5 second to turn on the adapter. The adapter will connect back to last paired devices.

• When turn on rst time, Red and Blue LED blinks. When connected, the Blue LED blinks once every ve seconds.

• Click MFB button 1 time to play or pause music.

• Double click MFB button to play next track.

• Click MFB button three times to play previous track.

Note: this function is valid when your Smartphone supports AVRCP.

General Pairing Notes:

• Some devices, such as an iPhone, connect immediately after pairing so the blue LED on the Bluetooth audio adapter

. Other devices,

such as notebook computers, may ask you if you wish to connect. In this instance, the

until a connection is established.

• Your Bluetooth audio adapter saves pairing information for up to two devices in each mode.

• When you turn on your Bluetooth audio adapter, it automatically connects to the last connected device if that device is in ra

• The auto-connect feature may not work with some Bluetooth devices. If this occurs, use your Bluetooth device settings menu to manually select Insignia

NS-HPBTAA23 from the list of found Bluetooth devices.

Understanding LED indicators (RX mode)

INDICATOR

Red and blue LEDs blink alternatively for 1 second

Blue and red LEDS blink alternatively for 1 second

Red and blue blinking

Blue LED blinks once every 5 seconds

Blue LED blinks slowly

DESCRIPTION

Adapter is turned on

Searching for Bluetooth device

Bluetooth device is connected

Disconnected from Bluetooth device

Home theater receiver

Car Audio system

Marine Audio system