MODEL M5800SB-SU-EXT 5.8 GHz Digital Spread Spectrum Wireless Internet Subscriber Unit Installation and Operating Instructions SUNSTREAM WIRELESS, A DIVISION OF TRANGO SYSTEMS, INC.
1•Setup transceiver per instructions herein before installing outdoors. 2•Mount the dish antenna to a wall or earth grounded mast 1.5 to 2.5 inches in diameter. 3• Install transceiver to dish antenna mounting arm. The pole must be securely mounted so that it does not move, and may be from 1.5” to 3” in diameter. WARNING USE EXTREME CARE WHEN INSTALLING ANTENNAS NEAR POWER LINES. 4• Slide heatshrink over antenna cables.
Thank you for choosing Sunstream Wireless to fulfill your wireless internet access needs. Unpack your system carefully. If any items are missing, notify your sales representative. If an item appears to be damaged from shipment, replace it in its packing material and notify the shipper.
Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty.
System Description: The M5800SB-SU-EXT is a broadband wireless internet access system designed for sending and receiving Ethernet based data traffic where conventional wiring is impractical or when higher connection speeds are required. The system utilizes robust spread spectrum technology to reduce susceptibility to interference. The typical subscriber installation consists of an M5800SB-SU-EXT transceiver mounted outdoors with a dish antenna and a junction box mounted indoors.
• FIGURE 1 • Figure 1 shows installation of the dish and transceiver. • FIGURE 2 • Figure 1 shows installation of the junction box and power adapter. 5 Copyright © 1999 Sunstream Wireless, LLC All rights reserved.
Installation: Typically the service provider will program the transceiver and professionally install the entire system. If you are installing the system yourself, below you will find a step by step guide. TRANSCEIVER SETUP PRIOR TO INSTALLATION Before installing the hardware you must set up the transceiver to allow communication with the base station. Your service provider should provide a .cfg file to you that contains all the required information. 1) Obtain the M5800S-SU Series Wizard program, .
1) Keep the transmission path as open as possible. Objects such as walls and metallic objects near the transmission path reflect signals and may reduce the transmission distance. 2) Do not add additional lengths of cable to connect the to the antenna as significant losses in signal and reduced transmission range will occur. 3) Mount the transceiver on the dish mounting pole as shown in Figure 1. 4) Connect the antenna cables, paying attention to the polarization shown on the feed.
M5800SB-SU-EXT Inputs and Outputs 1. POWER INPUT Accepts a 10.5-24 Vdc power source such as the standard 20 Vdc adapter (supplied with Sunstream part number ODU-PKIT-1). 2. ETHERNET DATA INTERFACE Use a shielded cat 5 cable to connect the junction box to the transceiver unit. It is ok to us UTP for the indoor connection to the switch or PC. 4. LED INDICATORS These LEDs indicate when a data packet is transmitted(red) or received (green).
Modulation: 1 MBPS DBPSK for header, 11 MBPS CCK spread spectrum for payload Data Input Section Buffer size: Data Rate (User): Format: Ethernet packet size: 128K Bytes Up to 9.5 MBPS Sustained throughput 10/100 BaseT IEEE 802.3 Ethernet compliant Up to 1760 byte long packets Power Input Voltage: Current Cons.: Input voltage range at unit is 10.5 VDC to 24 VDC max Power is supplied on Ethernet cable using junction box provided with up to 150 foot STP cable.
Mechanical and Environmental General Material: Size: Weight: Mounting: Powdercoated Aluminum base with polycarbonate radome 12.5”x5”x8” including mounting studs 4 lb Grey steel pole mount provided Connectors/Indicators RF Output: Direct connect to antenna per Part 15C, 15.203. FCC Compliance: The transceiver shall comply with the following: FCC Part 15.247 FCC Part 15.