User Manual

ManualsBrandsTrango Systems ManualsElectronicsSpread Spectrum Transmitter

MODEL M5800SB-AP-60

5.8 GHz Digital Spread-Spectrum Wireless Internet Access Point

Installation and Operating Instructions for the

SunStream5800™ Broadband Access Solution

Access Point Manual

Information contained in this manual is for the use of SunStream Wireless’ Beta Test Users and

Customers. The information contained in this document is subject to change with or without

notice. Please contact your Beta Program coordinator for updates and/or amendments to this

and/or any other supplied documents. No warranties to performance are expressed or implied

while Beta trials are underway.

SUNSTREAM WIRELESS, A DIVISION OF TRANGO SYSTEMS, INC.

Summary of content (10 pages)

PAGE 1
MODEL M5800SB-AP-60 5.8 GHz Digital Spread-Spectrum Wireless Internet Access Point Installation and Operating Instructions for the SunStream5800™ Broadband Access Solution Access Point Manual Information contained in this manual is for the use of SunStream Wireless’ Beta Test Users and Customers. The information contained in this document is subject to change with or without notice. Please contact your Beta Program coordinator for updates and/or amendments to this and/or any other supplied documents.
PAGE 2
Page 1 of 9 Access Point Manual QUICK SETUP GUIDE 1 Read through these instructions fully before doing anything! 2 Using the instructions provided, configure the radio settings before installing outdoors. 3 Mount the optional mounting arm to an earth-grounded mast measuring approximately 1.5 to 2.5 inches in diameter. The mast must be securely mounted to the mast. 4 Attach the radio to the dish antenna mounting arm using the supplied “V” brackets and nuts.
PAGE 3
Page 2 of 9 Access Point Manual Thank you for choosing SunStream Wireless to fulfill your wireless Internet access needs. Unpack your system carefully.
PAGE 4
Access Point Manual Page 3 of 9 IMPORTANT NOTE: Intentional or unintentional changes or modifications must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. To comply with FCC RF exposure requirements, the following antenna installation and device operating configurations must be satisfied.
PAGE 5
Access Point Manual Page 4 of 9 One (1) length of CAT5 cable, not to exceed 50 meters, to carry Ethernet traffic. This cable will be connected one on end to the Junction Box and the other end to a Network Interface Card (NIC); i.e., router and/or PC (depending on wiring). Appropriate hardware tools such as adjustable wrench, Ethernet crimping tool, wire-cutter/stripper, Philips screwdriver and/or ladder.
PAGE 6
Page 5 of 9 Access Point Manual FIGURE 1 An Access Point radio properly attached. There is a single CAT5 cable that provides power and data to the Access Point. The Access Point is mounted to a pole using an optional pole mount bracket. Symbol Description A Mounting Hole B LED ON = Access Point OK C ODU Port – connects to AP (RJ45 Port w.
PAGE 7
Access Point Manual Page 6 of 9 FIGURE 3 A bottom view of an Access Point showing power/data cable feed and access door. The access door can be removed during installation for access to the internal serial port. Link status can be checked with the access door attached; LEDs will show TX and RX packet activity will show as well as RSSI through the opening in the access door. SunStream Wireless, a division of Trango Systems, Inc.
PAGE 8
Page 7 of 9 Access Point Manual Installation: Typically, the service provider will program the radio and professionally install the entire system. However, if you are installing the system yourself, below is a stepby-step installation procedure to guide you. FIRST STEP: RADIO SET-UP PRIOR TO INSTALLATION Before installing the hardware, you must set up the radio operating parameters and load the initial subscriber unit information into the database. The following steps will guide you through this process.
PAGE 9
Access Point Manual Page 8 of 9 19) Before any communications with subscriber units will occur, subscribers must be loaded into the unit’s database. Log into the unit again using the AP wizard program and select “Wizard Tree” from the “PG-SYSINFO” page. 20) Select “Add Entry” under the “SU Database Management” heading, then click “Run”. 21) Enter the appropriate information for the subscriber. 22) Select “Write SU Database to Flash Memory” to save the changes.
PAGE 10
Access Point Manual Page 9 of 9 THIRD STEP: CONNECTION VERIFICATION After the alignment is completed, an Ethernet cable can be connected to the “NET” port of the Junction Box and then to a switched hub or PC network card. NOTE: A crossover cable will be required if connecting to a PC NIC. CAUTION DO NOT APPLY POWER TO THE RADIO UNTIL THE ANTENNA IS SECURELY ATTACHED. M5800SB-AP-EXT Inputs and Outputs 1. POWER INPUT The unit accepts a 10.