7.2 Selecting a Network Available broadcasting networks with an adequate signal strength will display their SSIDs (Service Set IDentifiers) in this screen. A closed lock icon next to the SSID indicates a secure network. An open lock indicates a non-secure, “open” network. Select your network and press “Connect”. The signal strength is indicated in bars. The more bars, the better the signal strength.
7.3 Enter Network Key/Password 1A)If the network is unsecured (with an “open” padlock), the following message will be displayed. 1B)If the network is secured (with a “closed” padlock), the following message will be displayed. 3) The control will connect to the wireless network. 4) When the control has successfully joined the wireless network, the name of the network will be displayed with a green dot to the left and a signal strength indicator to the right.
7.4 Advanced Networking Information Enter the Advanced Network Setup Menu. Advanced networking will be required in the following two instances: 1. When connecting to a non-broadcast network 2. When configuring a static IP address IMPORTANT: The Advanced Network screens are intended for individuals with networking familiarity. You or your network administrator will need to provide the required information.
7.5 Network Security When the network’s SSID is not broadcast (hidden), manual configuration in this screen is required. 1) The “Network Security” button in this Advanced Network Settings menu will be highlighted by default. 2) Press the “Enter SSID Name” button. 3) Enter the SSID Name using the on-screen keypad. 4) Select a network security type.* 5) Press “Enter Network Key” button. 6) Enter the Network Key using the on-screen keypad. *NOTE: WEP-Shared is not supported.
7.6 Host Settings This screen is used to manage how the control obtains network addresses and is needed when DHCP (Dynamic Host Configuration Protocol) has been turned off or is not available on the router. Otherwise, you may use DHCP to automatically obtain this information. This manual configuration is required if a static IP address is desired. NOTE: No additional configuration may be required in a non-broadcast network where IP addresses are assigned by DHCP.
7.7 Network Properties The Network Properties screen displays the control’s current network information. 7.8 Disconnecting from a Network Once a network has been joined, the control will reconnect to it after signal or power interruptions. When connected, a green dot will be shown. To disconnect from this network, enter the “Connect to a Network” menu and select “Disconnect”. NOTE: When joining a different network, the current router must be disconnected in this menu before a new one may be selected.
.9 Zoned Environments 1) In a zoned environment, the “Zones” button will appear in place of the “System” button (see picture at right). 3) In zoned environments, the main screen display will change to indicate the presence of multiple zones. (Notice the new zone button—labeled “Upstairs”—at right.) Arrow buttons navigate between zone views. 2) The Zone Menu is shown at right. 4) The Zone Overview menu shows a quick view of each zone’s current condition.
5) System wide settings for all zones can be seen at a glance in the System Status screen. 7) Each zone’s schedule can be viewed by cycling through the zones using the arrows in the top left corner. 6) A schedule for one zone can be copied to another. 8) System and Zone Names may be set in the Zone Names screen. The “Rename System” and “Rename Zone” buttons allow entering custom names from a keypad. Pre-configured names are also available.
8 Wireless Registration Registration is required for Weather, Software Updates and linking two or more controls together. Registration ensures that your control is using the most up-to-date software and will also let you take advantage of exciting new features in the future. You will be notifed via email when there is a software upgrade available. For complete privacy information see our Privacy Policy at americanstandardair.com.
9) Enter the 5-digit verification code. NOTE: This will only need to be done one time. 9 Nexia™ Home Intelligence Enrollment The control can be managed remotely via an internet connected computer and most smart cell phones via Nexia™ Home Intelligence. Visit www.nexiahome.com to learn more. 1) Visit www.nexiahome.com to sign on and add your new control to your account or click on “Ready to setup a Nexia™ Home Intelligence system? Get started here!” to set up a new Nexia™ account.
10 Software Upgrades Your control is built with the future in mind and has the ability to upgrade its operating system. Software upgrades ensure your control has the most up-to-date software optimizing its operation and providing exciting new features as they become available. Requirements • • • You must have a currently active internet connection. You must already have registered your control (see previous section). You must have an SD card with adequate memory available.
11 Troubleshooting Slow response or unexpected operation: Reboot your control at the following location. “No System Found” displays on the screen: If this message stays on your screen, press the “Reboot” button shown at right. No response to any button presses: Remove and re-install the control as shown below. The boot up process may take several minutes. Remove Control Re-Install Control Remove control from its sub-base by grasping at edges and gently pulling the control straight towards you.
System Alerts 1) When your system indicates an issue with communication or operation, an alert will display on the screen. Click the “Dealer Contact Info” to retrieve your dealer’s phone numbers and website information. 2) Press “Close” to dismiss the alert. The error message can be recalled by pressing the Alert icon which will remain in the menu bar.
12 Networking Diagnostics Networking Diagnostics allows the user to view information about the: 1) Wireless Connection (connection to the local router), 2) Internet Connection (connection to the Internet), 3) Server Access (the 950’s ability to call out and connect to the Registration and Data Logging Server) and 4) Nexia Access (the 950’s ability to call out and connect to the Nexia server). The 950 automatically performs these four test each time the Network Diagnostics screen is entered.
Base Limited Warranty Subject to the terms and conditions of this limited warranty, Trane U.S., Inc. (“Company’) extends a limited warranty against manufacturing defects for the product(s) identified in Tables 1, 1A, 1B attached hereto (“Products’) that are installed in a residential/ multi-family application (personal, family or household purposes) under normal use and maintenance in the United States and Canada. This limited warranty applies to Products manufactured on or after August 1, 2011.
EXCLUSIONS: The following are not covered by this limited warranty: • Labor costs including, but not limited to, costs for diagnostic calls or the removal and reinstallation of Products and/or Product parts. • Shipping and freight expenses required to ship Product replacement parts.
Table 1A: Warranty Time Periods for Controls, Zoning Products, Humidifiers, Energy Recovery Ventilators, and Air Cleaners COVERAGE TERMS FOR RESIDENTIAL APPLICATIONS: Pursuant to the Trane U.S., Inc. (“Company”) limited warranty terms and conditions, the following Products are covered for the base time periods as stated below (“Base Limited Warranty period”). If registered, the Base Limited Warranty Periods for certain products will be extended as stated below (“Registered Limited Warranty Period”).
FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
6200 Troup Highway Tyler, TX 75707 © 2015 American Standard Heating & Air Conditioning 01/15 12-5052-05 The manufacturer has a policy of continuous product and product data improvement and it reserves the right to change design and specifications without notice.