Access Management Keypad Installation Guide Please call ZTR IIoT Technical Support With any questions: 1-888-320-8332
Access Management Keypad Installation Guide This page was left blank intentionally. Title: Author: Access Management Keypad Installation Guide Christopher R. Boltë PN: VER: xxxxxx Page: 2 of 14 2.
Access Management Keypad Installation Guide ZTR Control Systems – K1 (Keypad) Device Regulatory and Compliance Statements – FCC/ISED ISED Regulatory Statements IC: 22769-112015 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference.
Access Management Keypad Installation Guide OWNERSHIP AND CONFIDENTIALITY The Software, Software Materials and Printed Documents constitute proprietary property of ZTR Control Systems (ZTR) and include trade secrets and confidential information of ZTR. Customer acknowledges that it acquires only the right to use the Software and Software Materials as permitted hereunder and does not acquire any ownership, right or title in or to the Software, the Software Materials or any Third Party Software.
Access Management Keypad Installation Guide Contents 1. Introduction .............................................................................................................................................. 6 2. Installation Requirements ........................................................................................................................ 6 3. Supplies .....................................................................................................................................
Access Management Keypad Installation Guide 1. Introduction ** PLEASE READ THESE INSTALLATION INSTRUCTIONS THROUGH FIRST TO BECOME FAMILIAR WITH THE INSTALLATION, WIRING AND TESTING PROCEDURES. THIS WILL SAVE INSTALLATION TIME AND BETTER PREPARE YOU FOR TESTING ** This manual includes instructions for installation of the ZTR Access Management Keypad. The following instructions and any accompanying documentation, drawings and specifications are the property of ZTR CONTROL SYSTEMS.
Access Management Keypad Installation Guide b. What is Not Included in the Kit: The following are supplies that are not provided in this kit which you will need to use during the installation of the Access Control Keypad: Cable Tie’s 2 x #8 Hex Machine screws Length to be determined based on mounting surface thickness + ½ in. 2 x #8 Nylon lock nuts 3/8 in. Dia. Split Loom, 3 feet **Please be sure to meet your company’s Standard Safety Protocols for Installations** 4.
Access Management Keypad Installation Guide Label on back side Figure 1: Keypad Serial Number Label 5. Keypad Mounting Refer to Figure 2, 3 and 4 below to understand how the keypad should be mounted on the surface selected in section 3. Take the following steps to complete the keypad mounting. 1 In. Dia. Hole 1 In. Figure 2: Front View of Keypad Mounted Figure 3: Rear View of Keypad Mounted a.
Access Management Keypad Installation Guide b. Mark a center point about 1 inch up from the bottom mounting hole as the landmark for where to drill the 1 in. dia. hole that the keypad harness must pass through (Figure 3) c. Wrap the 3/8 in. dia. split loom around the keypad harness and slide it up into the notch at the back of the keypad (Figure 4, 5) d. With all holes drilled and split loom in place, slide the keypad’s harness through the 1 in. dia.
Access Management Keypad Installation Guide Notch for Split Loom Figure 5: Keypad Notch and Channel f. With the keypad secured, rout the 3 foot keypad harness so it can be connected to the M7 patch cable g. Connect the keypad harness and patch cable h. Insert the Access Control harness** between the M7 and the main machine harness it is connected to i.
Access Management Keypad Installation Guide Title: Author: Access Management Keypad Installation Guide Christopher R. Boltë PN: VER: xxxxxx Page: 11 of 14 2.
Access Management Keypad Installation Guide Appendix A: Access Management Keypad LED’s The diagram below illustrates the 3 LED’s, their respective color’s and designation. Yellow LED = Power Condition Keypad Awake Keypad Asleep LED ON OFF Green LED = Access Status Condition Assessing Credentials Access Granted LED Blinking ON Red LED = Diagnostics Condition Error Normal Operation LED ON OFF Title: Author: Access Management Keypad Installation Guide Christopher R.
Access Management Keypad Installation Guide Appendix B: Label Revision History This section will illustrate any changes to the product label as a result of a revision/update. Revision: 1 Title: Author: Date: (MM/DD/YYYY) 01/29/2019 Access Management Keypad Installation Guide Christopher R. Boltë Author: C. Moulton PN: VER: Reason: Initial release xxxxxx Page: 13 of 14 2.
Access Management Keypad Installation Guide Appendix C: Installation Guide Revision History This section will detail any changes to the content of this document as a result of a revision/update. Revision: 1.0 2.0 2.1 2.2 2.3 2.4 Title: Author: Date: (MM/DD/YYYY) 01/29/2019 04/17/2019 04/22/2019 04/24/2019 05/09/2019 05/14/2019 Access Management Keypad Installation Guide Christopher R. Boltë Author: C. Boltë C. Boltë C. Boltë Pierre Wheeler C. Boltë C.